Chamberlain 8010 Manual
Chamberlain 8010 Manual

Chamberlain 8010 Manual

Chain/cable drive dc garage door opener
Hide thumbs Also See for 8010:

Advertisement

Quick Links

Chain/Cable Drive DC
Garage Door Opener
Model 8010
FOR RESIDENTIAL USE ONLY
INSTALL ON 7 OR 8 FOOT
SECTIONAL DOORS ONLY
Register your garage door opener to receive
updates and offers from LiftMaster
Take a photo of the camera icon including
the points ( ).
Send it in by texting the photo to 71403
(US) or visit
www.liftmaster.com/register (Global)
■ Please read this manual and the enclosed safety materials carefully!
■ Fasten the manual near the garage door after installation.
■ The door WILL NOT CLOSE unless the Protector System
properly aligned.
■ Periodic checks of the garage door opener are required to ensure safe operation.
■ The model number label is located on the back panel of your garage door opener.
■ This garage door opener is compatible with Security+ 2.0
■ WARNING: To reduce the risk of injury to persons - Use this opener ONLY with a
7 or 8 foot sectional door.
®
is connected and
®
accessories.
Write down the following information
for future reference:
Model Number:
Serial Number:
Date of Purchase:
CONTENTS
Preparation .............................. 1-5
Assembly ................................. 6-7
Installation ..............................8-23
Adjustments .......................... 24-26
Operation.............................. 27-30
Maintenance .............................. 31
Troubleshooting .......................... 32
Warranty .................................. 33
Repair Parts .............................. 34
Contact Information ..................... 35
LiftMaster.com
LiftMaster
300 Windsor Drive
Oak Brook, IL 60523

Advertisement

Table of Contents
loading

Summary of Contents for Chamberlain 8010

  • Page 1: Table Of Contents

    CONTENTS Chain/Cable Drive DC Preparation ......1-5 Assembly ......... 6-7 Garage Door Opener Installation ......8-23 Model 8010 Adjustments ......24-26 Operation......27-30 FOR RESIDENTIAL USE ONLY Maintenance ......31 INSTALL ON 7 OR 8 FOOT SECTIONAL DOORS ONLY Troubleshooting ......32 Warranty ........
  • Page 2: Preparation

    Preparation Safety Symbol and Signal Word Review Check the Door This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual.
  • Page 3 Preparation Additional Items You May Need: Tools Needed Survey your garage area to see if you will need any of the following items: (2) 2X4 PIECES OFWOOD May be used to fasten the header bracket to the structural supports. Also used to position the garage door opener during installation and for testing the safety reversing sensors.
  • Page 4 Preparation Carton Inventory Accessories will vary depending on the garage door opener model purchased. Depending on your specific model, other accessories may be included with your garage door opener. The instructions for these accessories will be attached to the accessory and are not included in this manual. The images throughout this manual are for reference and your product may look different.
  • Page 5 Preparation Hardware 041A8068 ASSEMBLY INSTALLATION DOOR CONTROL Lag Screw 5/16"-9x1-5/8" (2) Wing Nut 1/4"-20 (2) Ring Fastener (3) Self-Threading Screw 1/4"-20x1-3/4" (2) Screw 6ABx1" (2) Clevis Pin 5/16"x1-1/2" Clevis Pin 1/4"x1-1/4" Clevis Pin 5/16"x1" Drywall Anchors (2) Insulated Staples Carriage Bolt Lock Nut 1/4"-20 (4) Self-Threading Screw Hex Bolt 1/4"-20x3/4"...
  • Page 6: Assembly

    Assembly 1 Attach the Rail to the Garage Door Opener Sprocket To avoid SERIOUS damage to garage door opener, use ONLY the 1/4"-20x1-3/4" self-threading screws provided. Outer Trolley To avoid installation difficulties, do not run the garage door opener until instructed to do so. 1.
  • Page 7 Assembly 2 Tighten the Chain Trolley Outer Lock Threaded Washer 1. Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley. Shaft To Tighten Outer Nut 2. To tighten the chain, turn the outer nut in the direction shown. 3.
  • Page 8: Installation

    Installation IMPORTANT INSTALLATION INSTRUCTIONS To reduce the risk of SEVERE INJURY or DEATH: 1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS. 9. Install wall-mounted garage door control: 2. Install garage door opener ONLY on properly balanced and lubricated garage door. An within sight of the garage door.
  • Page 9 Installation 1 Determine the Header Bracket Location OPTIONAL Unfinished CEILING Ceiling MOUNT FOR HEADER Header Wall BRACKET To prevent possible SERIOUS INJURY or DEATH: Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, Vertical Centerline of Garage Door otherwise garage door might NOT reverse when required.
  • Page 10 Installation 2 Install the Header Bracket OPTION B CEILING INSTALLATION 1. Extend the vertical centerline onto the ceiling as shown. You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the 2.
  • Page 11 Installation 3 Attach the Rail to the Header Bracket 4 Position the Garage Door Opener 1. Align the rail with the header bracket. Insert the clevis pin through the holes in the header bracket and rail. Secure with the ring fastener. NOTE: Use the packing material as a protective base for the garage door opener.
  • Page 12 Installation 5 Hang the Garage Door Opener 1. On finished ceilings, use the #14-10x1-1/2" lag screws to attach a support bracket (not provided) to the structural supports before installing the garage door opener. 2. Make sure the garage door opener is aligned with the header bracket. Measure the distance from each side of the garage door opener to the support bracket.
  • Page 13 Installation 6 Install the Light Bulb 7 Attach the Emergency Release Rope and Handle To prevent possible OVERHEATING of the endpanel or light socket: To prevent possible SERIOUS INJURY or DEATH from a falling garage door: Use ONLY A19 incandescent (60W maximum) or compact fluorescent (23W maximum) light If possible, use emergency release handle to disengage trolley ONLY when garage door is bulbs.
  • Page 14 Installation 8 Install the Door Bracket Metal, insulated or light weight factory reinforced doors: Drill 3/16" fastening holes. Secure the door bracket using the self-threading screws. (Figure 3) Wood Doors: Use top and bottom or side to side door bracket holes. Drill 5/16” holes through the door and secure bracket with 5/16"-18 x 2"...
  • Page 15 Installation 9 Connect the Door Arm to the Trolley CORRECT INCORRECT IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm. Straight Straight Door 1. Close the door. Disconnect the trolley by pulling the emergency release handle. Curved Door Arm Curved...
  • Page 16 Installation 10 Install the Door Control 1. Strip 1/4" (6 mm) of insulation from one end of the wire and separate the wires. 2. Connect one wire to each of the two screws on the back of the door control. The wires can be connected to either screw.
  • Page 17 Installation 11 Wire the door control to the garage door opener 12 Attach the warning labels HARDWARE 1. Attach the entrapment warning label on the wall near the door control with tacks or staples. 2. Attach the manual release/safety reverse test label in a visible location on the inside of the Insulated Staple garage door.
  • Page 18 Installation ® 13 Install the Protector System HARDWARE Carriage Bolt Wing Nut 1/4"-20 x 1/2" 1/4"-20 Be sure power is NOT connected to the garage door opener BEFORE installing the safety The safety reversing sensors can be attached to the door track, the wall, or the floor. The sensors should reversing sensor.
  • Page 19 Installation ® 13 Install the Protector System (continued) OPTION C FLOOR INSTALLATION Use an extension bracket (not provided) or wood block to raise the sensor bracket if needed. OPTION B WALL INSTALLATION 1. Carefully measure the position of both sensor brackets so they will be the same distance from If additional clearance is needed an extension bracket (not provided) or wood blocks can be used.
  • Page 20 Installation 14 Wire the Safety Reversing Sensors Staple If your garage already has wires installed for the safety reversing sensors, see page 21. HARDWARE Insulated Staple (Not Shown) 7/16" (11 mm) OPTION A INSTALLATION WITHOUT PRE-WIRING 1. Run the wire from both sensors to the garage door opener. Attach the wire to the wall and ceiling with the staples.
  • Page 21 Installation OPTION B PRE-WIRED INSTALLATION Pre-installed 1. Cut the end of the safety reversing sensor wire, making sure there is enough wire to reach the Safety reversing wires 7/16" sensor wires pre-installed wires from the wall. (11 mm) 2. Separate the safety reversing sensor wires and strip 7/16 inch (11 mm) of insulation from each end.
  • Page 22 Installation 15 Connect Power OPTION B PERMANENT WIRING If permanent wiring is required by your local code, refer to the following procedure. To make a permanent connection through the 7/8 inch hole in the top of the motor unit (according to local code): 1.
  • Page 23 Installation 16 Aligning the Safety Reversing Sensors IF THE AMBER LED ON THE SENDING SENSOR IS NOT GLOWING: 1. Make sure there is power to the garage door opener. The door will not close if the sensors have not been installed and aligned correctly. 2.
  • Page 24: Adjustments

    Adjustments Introduction PROGRAMMING BUTTONS The programming buttons are located on the back panel of the garage door opener and are used to program the travel. While programming, the UP and DOWN buttons can be used to move the door as needed.
  • Page 25 Adjustments 1 Program the Travel PROGRAMMING BUTTONS UP Button Adjustment Without a properly installed safety reversal system, persons (particularly small children) could be Button SERIOUSLY INJURED or KILLED by a closing garage door. Incorrect adjustment of garage door travel limits will interfere with proper operation of safety DOWN Button reversal system.
  • Page 26 Adjustments ® 2 Test the Safety Reversal System 3 Test the Protector System Without a properly installed safety reversal system, persons (particularly small children) could be Without a properly installed safety reversing sensor, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. SERIOUSLY INJURED or KILLED by a closing garage door.
  • Page 27: Operation

    Operation IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of SEVERE INJURY or DEATH: 1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS. 9. After ANY adjustments are made, the safety reversal system MUST be tested. 2. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or 10.
  • Page 28 Operation Features LIGHTS The garage door opener light bulbs will turn on when the opener is initially plugged in; power is Your garage door opener is equipped with features to provide you with greater control over your restored after interruption, or when the garage door opener is activated. The lights will turn off garage door operation.
  • Page 29 Operation Using Your Garage Door Opener Remote Control The garage door opener can be activated through a wall-mounted door control, remote control, or Your remote control has been programmed at the factory to operate with your garage door wireless keyless entry. opener.
  • Page 30 Operation To Erase the Memory To Open the Door Manually ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES 1. Press and hold the LEARN button on garage door opener until the learn LED goes out (approximately 6 seconds). All remote control and keyless entry codes are now erased. To prevent possible SERIOUS INJURY or DEATH from a falling garage door: Reprogram any accessory you wish to use.
  • Page 31: Maintenance

    Maintenance Maintenance Schedule The Remote Control Battery EVERY MONTH Manually operate door. If it is unbalanced or binding, call a trained door systems technician. Check to be sure door opens and closes fully. Adjust if necessary, see page 25. Test the safety reversal system. Adjust if necessary, see page 26. To prevent possible SERIOUS INJURY or DEATH: EVERY YEAR NEVER allow small children near batteries.
  • Page 32: Troubleshooting

    Troubleshooting Diagnostic Chart Your garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage door opener flash the diagnostic codes. NOTE: For troubleshooting questions, please visit LiftMaster.com. DIAGNOSTIC CODE SYMPTOM SOLUTION Up Arrow Down Arrow Flash(es) Flash(es) The garage door opener will not close and the light...
  • Page 33: Warranty

    Warranty ® LIFTMASTER LIMITED WARRANTY ® LiftMaster (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally installed, that it is free from defects in materials and/or workmanship for a specific period of time as defined below (the “Warranty Period”).
  • Page 34: Repair Parts

    Repair Parts Installation Parts Garage Door Opener Parts Description Part # Description Part # Header Bracket 041A5047-2 Logic board 047DCT Door Bracket 041A5047-1 Light lens 041D0166 Trolley 41C5141-1 Cover 041D0671 ® The Protector System 41A5034 Door control 883LM Safety reversing sensors with 2 conductor white and white/black wire attached: Sending Sensor (1), Receiving Sensor (1) Safety Sensor Brackets (2) 041A5266-1...
  • Page 35: Contact Information

    Contact Information STOP! This garage door opener WILL NOT work until the safety reversing sensors are properly installed and aligned. For installation and service information please: See your installing dealer Visit LiftMaster.com Call 1-800-528-9131 Before calling, please have the model number of the garage door opener. If you are calling about a troubleshooting issue, it is recommended that you have access to your garage door opener while calling.
  • Page 36 © 2017, LiftMaster 114A4977 All Rights Reserved...

Table of Contents