Related Manuals for SHOWTEC Performer Pendant Q6 V3
Summary of Contents for SHOWTEC Performer Pendant Q6 V3
- Page 1 USER MANUAL ENGLISH Performer Pendant Q6 Product code: 33150 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
- Page 2 Performer Pendant Q6 Preface Thank you for purchasing this Showtec product. The purpose of this user manual is to provide instructions for the correct and safe use of this product. Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
-
Page 3: Table Of Contents
Performer Pendant Q6 Table of contents Introduction ................................4 Before Using the Product ..........................4 Intended Use ............................... 4 Product Lifespan ..............................4 LEDs Lifespan ............................... 4 Text Conventions ..............................4 Symbols and Signal Words ..........................5 Symbols on the Information Label ........................5 Safety .................................. - Page 4 Performer Pendant Q6 Key (Display Lock) ..........................30 Disp Time ..............................30 Wireless Reset ............................30 Signal ..............................31 Information ..............................31 Fixture Hours ............................31 Version ..............................31 RDM ...............................31 Correlated Color Temperature Control (CCT) ..................32 Preset Color .............................33 DMX Channels ..............................34 8 Channels, 13 Channels, 20 Channels ....................34 7 Channels ..............................36 8 Channels ..............................37 Supported RDM PIDs (Parameter IDs) ......................39...
-
Page 5: Introduction
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer. Your shipment includes: ● Showtec Performer Pendant Q6 with a bare- end power cable (2,4 m) ● 2 x aluminum spacer ●... -
Page 6: Symbols And Signal Words
Performer Pendant Q6 ● References: References to chapters and parts of the device are in bold lettering, for example: “Refer to 2. Safety”, “turn the adjustment screw (02)” ● 0–255: Defines a range of values ● Notes: Note: (in bold lettering) is followed by useful information or tips Symbols and Signal Words Safety notes and warnings are indicated throughout the user manual by safety signs. -
Page 7: Safety
Performer Pendant Q6 Safety Important Read and follow the instructions in this user manual before installing, operating or servicing this product. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual. Warnings and Safety Instructions DANGER Danger for children For adult use only. - Page 8 Performer Pendant Q6 WARNING Risk of burns due to hot surface The surface and the inner parts of the device can become very hot during operation. ● Do not touch the device during operation. ● Allow the device to cool down for at least 15 minutes before handling. WARNING Risk of epileptic shock Strobe lighting can trigger seizures in photosensitive epilepsy.
-
Page 9: Requirements For The User
Performer Pendant Q6 ● If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it on immediately. Let the device reach room temperature before switching it on, otherwise it may be damaged by the formed condensation. ●... -
Page 10: Description Of The Device
Performer Pendant Q6 Description of the Device The Performer Pendant Q6 is a true house light and is equipped with the same LED engine as the Performer Fresnel series and, therefore, can set your auditorium in the same colors as your stage. It has a CCT channel enabling you to set the white light between 1800–8000 K, still ensuring a high CRI. -
Page 11: Back View
Performer Pendant Q6 Back View Fig. 03 Control panel: OLED display and control buttons Safety eye 5-pin DMX connector IN 5-pin DMX connector OUT Fuse T3,15AL/250 V Bare-end power cable (2,4 m) DMX terminal connectors IN/OUT Product code: 33150... -
Page 12: Product Specifications
Performer Pendant Q6 Product Specifications Model: Performer Pendant Q6 Electrical: Input voltage: 100–240 V AC, 50/60 Hz Power consumption: 155 W Max. power: 155 W Power factor: Fuse: T3,15AL/250 V Physical: Dimensions: 430 x 247 x 348 mm (LxWxH) Weight: 8,8 kg Optics: Light source:... -
Page 13: Optional Accessories
Performer Pendant Q6 Optional Accessories The Performer Pendant Q6 is delivered without accessories. You can additionally purchase the following accessories: Product code: 91300 (PCE Rubber Connector Male) Product code: 33155 (50° Lens set for Performer Pendant) Product code: 33156 (18° Lens set for Performer Pendant) Dimensions Fig. -
Page 14: Installation
Performer Pendant Q6 Installation Safety Instructions for Installation WARNING Incorrect installation can cause serious injuries and damage of property. If trussing systems are used, installation must be carried out only by instructed or skilled persons. Follow all applicable European, national and local safety regulations concerning rigging and trussing. Personal Protective Equipment During installation and rigging wear personal protective equipment in compliance with the national and site-specific regulations. -
Page 15: Rigging
Performer Pendant Q6 Rigging The device can be positioned on a flat surface or mounted to a truss or other rigging structure in any orientation. Make sure that all loads are within the pre-determined limits of the supporting structure. CAUTION Restrict the access under the work area during rigging and/or derigging. -
Page 16: Angle Adjustment
Performer Pendant Q6 Angle Adjustment You can adjust the angle of the device with the 2 adjustment screws (03). 01) Turn the adjustment screws (03) counterclockwise to release them. 02) Tilt the device to the desired angle (see Fig. 08). 03) Turn the adjustment screws (03) clockwise to tighten them. -
Page 17: Aluminum Spacers
Performer Pendant Q6 Aluminum Spacers It is possible to use the Performer without the mounting bracket. For aesthetic reasons, the mounting bracket mounting holes can be concealed by means of the included aluminum spacers. Turn the adjustment screws (03) counterclockwise until you remove them. Use a screwdriver to remove the 4 mounting screws. -
Page 18: Lens Replacement
Performer Pendant Q6 Lens Replacement It is possible to replace the lens when it is cracked or when you want to use one of the available optional lenses (18° or 50°). Loosen and remove the 4 mounting screws Remove the ring. Remove the old (or cracked) lens. -
Page 19: Connecting To Power Supply
Performer Pendant Q6 Connecting to Power Supply DANGER Electric shock caused by short-circuit The device accepts AC mains power at 100–240 V and 50/60 Hz. Do not supply power at any other voltage or frequency to the device. This device falls under IEC protection class I. Make sure that the device is always electrically connected to the ground (earth). -
Page 20: Dmx Connection
Performer Pendant Q6 DMX Connection DMX-512 Protocol You need a DMX serial data link to run light shows of one or more devices using a DMX-512 controller or to run synchronized shows of two or more devices set in a master/slave operating mode. The Performer Pendant Q6 has 5-pin DMX signal IN and OUT connectors. -
Page 21: Master/Slave Setup
Performer Pendant Q6 Master/Slave Setup The Performer Pendant Q6 supports master/slave control mode. To connect multiple devices in master/slave setup, follow the steps below: 01) Connect the first device’s DMX OUT connector to the second device’s DMX IN connector. 02) Repeat step 1 to connect all devices as shown in Fig. 13. 03) Connect a DMX terminator (120 Ω... -
Page 22: Dmx Addressing
Performer Pendant Q6 DMX Addressing In a setup with multiple devices, make sure that you set the DMX starting address of each device correctly. The Performer Pendant Q6 has 5 personalities: 7 channels, 8 channels, 8 channels, 13 channels and 20 channels. If you want to connect multiple devices on one data link and use them in 20-channel mode, for example, follow the steps below: 01) Set the starting address of the 1... -
Page 23: Operation
Performer Pendant Q6 Operation Safety Instructions for Operation Attention This device must be used only for the purposes it is designed for. This device is intended for professional use as a theater spot. It is suitable only for indoor installation. This device is not suitable for households and for general lighting. -
Page 24: Control Panel
Use the ENTER button to open the desired menu, to confirm your choice or to set the currently selected value. Start-up Upon start-up the display will show a splash screen with the logo of Showtec followed by the start screen. The start screen provides information about the currently active control mode and the temperature: Note: If no button is pressed, after 20 seconds of inactivity the display will return to the start screen and after 5 more seconds it will turn off. -
Page 25: Menu Overview
Performer Pendant Q6 Menu Overview Product code: 33150... - Page 26 Performer Pendant Q6 Product code: 33150...
-
Page 27: Main Menu Options
Performer Pendant Q6 Main Menu Options The main menu has the following options: Press the UP/DOWN buttons to navigate through the main menu. 04) Press the ENTER button to open the submenus. Note: Some of the submenus require a password. The default password is pressing the UP/DOWN buttons in the following order: UP, DOWN, UP, DOWN, ENTER. -
Page 28: Personality (Dmx Channel Modes)
Performer Pendant Q6 Personality (DMX Channel Modes) In this menu you can set the DMX channel mode (personality). 01) Press the UP/DOWN buttons to select the desired DMX channel mode. There are 4 options available: SSP: 8 channels HSIC: 7 channels TOUR: 13 channels CMY:... -
Page 29: Edit
Performer Pendant Q6 Edit In this menu you can edit the custom programs thus creating your own custom show. Press the UP/DOWN buttons to choose the custom program you want to edit (PROGRAM01–02). Press the ENTER button to confirm the selection. Each custom program has 10 scenes, which can be edited: Press the UP/DOWN buttons to select the desired scene. -
Page 30: Settings
Performer Pendant Q6 Settings In this menu you can adjust the device’s settings. This menu requires the password. The default password is pressing the UP/DOWN buttons in the following order: UP, DOWN, UP, DOWN. Enter the password to access the menu. Press the ENTER button to confirm the password. -
Page 31: Pwm Rate
Performer Pendant Q6 PWM Rate In this submenu you can set the PWM (Pulse Width Modulation) frequency. Select PWM RATE and press the ENTER button to open the submenu. Press the UP/DOWN buttons to choose the desired PWM frequency. The available options are: 1200 Hz, 2400 Hz, 4000 Hz, 6000 Hz, and 25000 Hz. -
Page 32: Signal
Performer Pendant Q6 Signal In this submenu you can set the signal preferences when wireless DMX is enabled. Press the UP/DOWN buttons to scroll through the following 2 options: Press the ENTER button to confirm your choice. The available options are: ●... -
Page 33: Correlated Color Temperature Control (Cct)
Performer Pendant Q6 Correlated Color Temperature Control (CCT) In this menu you can calibrate the color temperature. This menu requires the password. The default password is pressing the UP/DOWN buttons in the following order: UP, DOWN, UP, DOWN. Enter the password to access the menu. Press the ENTER button to confirm the password. -
Page 34: Preset Color
Performer Pendant Q6 Preset Color In this menu you can choose a preset color mix. Press the UP/DOWN buttons to select one of the 48 presets: Product code: 33150... -
Page 35: Dmx Channels
Performer Pendant Q6 DMX Channels SSP (8 CH), TOUR (13 CH), TR16 (20 CH) 8 CH 13 CH 20 CH Function Value Setting (SSP) (TOUR) (TR16) Master Dimmer 000–255 From low to high intensity (0–100 %) Dimmer Fine 000–255 From low to high intensity (0–100 %) 000–255 From low to high intensity (0–100 %) Red Fine... - Page 36 Performer Pendant Q6 8 CH 13 CH 20 CH Function Value Setting (SSP) (TOUR) (TR16) 186–190 Color 36 191–195 Color 37 196–200 Color 38 201–205 Color 39 206–210 Color 40 211–215 Color 41 216–220 Color 42 221–225 Color 43 226–230 Color 44 231–235 Color 45...
-
Page 37: Channels
Performer Pendant Q6 8 CH 13 CH 20 CH Function Value Setting (SSP) (TOUR) (TR16) 000–010 No Function 011–100 Reserved 101–110 Dimmer Off 111–120 Dimmer Mode 4 121–150 Reserved 151–160 1200 Hz Control Mode 161–170 2400 Hz 171–180 4000 Hz 181–190 6000 Hz 191–200... -
Page 38: Channels
Performer Pendant Q6 7 CH Function Value Setting (HSIC) 000–010 No Function 011–100 Reserved 101–110 Dimmer Off 111–120 Dimmer Mode 4 121–150 Reserved 151–160 1200 Hz Control Mode 161–170 2400 Hz 171–180 4000 Hz 181–190 6000 Hz 191–200 25000 Hz 201–210 All Reset 211–255... - Page 39 Performer Pendant Q6 8 CH Function Value Setting (CMY) 161–165 Color 31 166–170 Color 32 171–175 Color 33 176–180 Color 34 181–185 Color 35 186–190 Color 36 191–195 Color 37 196–200 Color 38 201–205 Color 39 206–210 Color 40 211–215 Color 41 216–220 Color 42...
-
Page 40: Supported Rdm Pids (Parameter Ids)
Performer Pendant Q6 Supported RDM PIDs (Parameter IDs) Parameter ID Discovery command SET command GET command DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE DEVICE_INFO SUPPORTED_PARAMETERS SOFTWARE_VERSION_LABEL DMX_START_ADDRESS IDENTIFY_DEVICE DEVICE_MODEL_DESCRIPTION MANUFACTURER_LABEL DEVICE_LABEL SENSOR_DEFINITION SENSOR_VALUE DEVICE_RESET DMX_PERSONALITY DMX_PERSONALITY_DESCRIPTION STATUS_MESSAGES STATUS_ID_DESCRIPTION Product code: 33150... -
Page 41: Troubleshooting
Performer Pendant Q6 Troubleshooting This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts. Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage. -
Page 42: Maintenance
Performer Pendant Q6 Maintenance Safety Instructions for Maintenance DANGER Electric shock caused by dangerous voltage inside Disconnect power supply before servicing or cleaning. WARNING Risk of burns due to hot surface Allow the device to cool down for at least 15 minutes before servicing or cleaning. Preventive Maintenance Attention Before each use, examine the device visually for any defects. -
Page 43: Basic Cleaning Instructions
Performer Pendant Q6 Basic Cleaning Instructions The external lens of the device must be cleaned periodically in order to optimize the light output. The cleaning schedule depends on the conditions at the site where the device is installed. When smoke or fog machines are used at the site, the device will need more frequent cleaning. -
Page 44: Deinstallation, Transportation And Storage
Performer Pendant Q6 Deinstallation, Transportation and Storage Instructions for Deinstallation WARNING Incorrect deinstallation can cause serious injuries and damage of property. ● Let the device cool down before dismounting. ● Disconnect power supply before deinstallation. ● Always observe the national and site-specific regulations during deinstallation and derigging of the device. - Page 45 Performer Pendant Q6 Product code: 33150...
- Page 46 Performer Pendant Q6 Product code: 33150...
- Page 47 Performer Pendant Q6 Product code: 33150...
- Page 48 ©2021 Showtec...