Related Manuals for SHOWTEC Performer Pendant 75 Q6
Summary of Contents for SHOWTEC Performer Pendant 75 Q6
- Page 1 USER MANUAL ENGLISH Performer Pendant 75 Q6 Product code: 33149 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
- Page 2 Performer Pendant 75 Q6 Preface Thank you for purchasing this Showtec product. The purpose of this user manual is to provide instructions for the correct and safe use of this product. Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
-
Page 3: Table Of Contents
Performer Pendant 75 Q6 Table of contents Introduction ................................4 Before Using the Product ..........................4 Intended Use ............................... 4 Product Lifespan ..............................4 LEDs Lifespan ............................... 4 Text Conventions ..............................4 Symbols and Signal Words ..........................5 Symbols on the Information Label ........................5 Safety .................................. - Page 4 Performer Pendant 75 Q6 Instructions for Transportation ........................31 Storage ................................31 10. Disposal ................................32 11. Approval ................................32 Product code: 33149...
-
Page 5: Introduction
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer. Your shipment includes: ● Showtec Performer Pendant 75 Q6 ● 1 x safety cable ● Power cable with open-end power cable (1,25 m) ●... -
Page 6: Symbols And Signal Words
Performer Pendant 75 Q6 Symbols and Signal Words Safety notes and warnings are indicated throughout the user manual by safety signs. Always follow the instructions provided in this user manual. Indicates an imminently hazardous situation which, if not avoided, will result in DANGER death or serious injury. -
Page 7: Safety
Performer Pendant 75 Q6 Safety Important Read and follow the instructions in this user manual before installing, operating or servicing this product. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual. Warnings and Safety Instructions... - Page 8 Performer Pendant 75 Q6 WARNING Risk of burns due to hot surface The surface and the inner parts of the device can become very hot during operation. ● Do not touch the device during operation. ● Allow the device to cool down for at least 15 minutes before handling.
-
Page 9: Requirements For The User
Performer Pendant 75 Q6 ● If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it on immediately. Let the device reach room temperature before switching it on, otherwise it may be damaged by the formed condensation. -
Page 10: Description Of The Device
Performer Pendant 75 Q6 Description of the Device The Showtec Performer Pendant 75 Q6 is a 70 watt RGBALC LED Fresnel. It is a fixed installation lamp (House Light) that works perfectly with show light to create an optimal atmosphere. Its 6-colour LED engine (red, green, blue, amber, lime, cyan) has 48 preset colours and provides highly accurate colour temperatures. -
Page 11: Back View
Performer Pendant 75 Q6 Back View Fig. 03 05) Fuse T3,15 A, 250 V 06) Safety eye 07) Phoenix connectors IN / OUT 08) Link button (Red + Green LED ) 09) 5-pin DMX signal connector OUT 10) Powercable 100–240 V AC, 50/60 Hz... -
Page 12: Product Specifications
Performer Pendant 75 Q6 Product Specifications Model: Performer Pendant 75 Q6 Electrical: Input voltage: 100–240 V AC, 50/60 Hz Power consumption: 70 W Fuse: F3,15A, 250 V Physical: Dimensions: 332 x 192 x 115 mm (L x W x H) -
Page 13: Dimensions
Performer Pendant 75 Q6 Dimensions Fig. 04 Fig. 05 Fig. 06 Fig. 07 Fig. 08 Product code: 33149... -
Page 14: Optional Accessories
Performer Pendant 75 Q6 3.5. Optional Accessories You have to additionally purchase the following accessory: 50409 (RDM Touch DMX Tester: for setting the DMX modes) Installation Safety Instructions for Installation WARNING Incorrect installation can cause serious injuries and damage of property. -
Page 15: Rigging
Performer Pendant 75 Q6 Rigging The device can be mounted to a truss or other rigging structure in any orientation, as shown in Fig. 09. Make sure that all loads are within the pre-determined limits of the supporting structure. CAUTION Restrict the access under the work area during rigging and/or derigging. -
Page 16: Angle Adjustment
Performer Pendant 75 Q6 Angle Adjustment You can adjust the angle of the device with the 2 adjustment screws (03). 01) Turn the adjustment screws (03) counterclockwise to release them. 02) Tilt the device at the desired angle (see Fig. 10). -
Page 17: Connecting To Power Supply
Performer Pendant 75 Q6 Connecting to Power Supply DANGER Electric shock caused by short-circuit The device is supplied with a power cord without a plug. The device is suitable for direct connection to the mains supply. Connection of the device to the mains supply must be carried out only by skilled or instructed persons. -
Page 18: Power Linking Of Multiple Devices
Do not link more devices on one power link than the maximum recommended number. Maximum recommended number of devices: ● at 100–120 V: 12 devices Performer Pendant 75 Q6 ● at 200–240 V: 25 devices Performer Pendant 75 Q6 Product code: 33149... -
Page 19: Setup
You need a DMX serial data link to run light shows of one or more devices using a DMX-512 controller or to run synchronized shows of two or more devices set in a master/slave operating mode. The Performer Pendant 75 Q6 has 5-pin DMX signal IN and OUT connectors. The pin assignment is as follows: ●... -
Page 20: Dmx Linking
Performer Pendant 75 Q6 Fig. 12 DMX Linking To connect multiple devices on one DMX data link, follow the steps below: Use a 5-pin DMX cable to connect the DMX OUT connector of the lighting controller to the DMX IN connector of the first device. -
Page 21: Dmx Addressing
DMX Addressing In a setup with multiple devices, make sure that you set the DMX starting address of each device correctly. The Performer Pendant 75 Q6 has 5 personalities: 7 channels, 8 channels, 8 channels, 13 channels and 20 channels. -
Page 22: Operation
Control Modes The Performer Pendant 75 Q6 can only be operated with a special RDM controller (example 50409). The Performer Pendant 75 Q6 supports the following control modes: ●... -
Page 23: Dmx Channels
Performer Pendant 75 Q6 DMX Channels HSIC (7 CH) 7 CH Function Value Setting (HSIC) Intensity 000–255 From low to high intensity (0–100 %) 000–255 From low to high intensity (0–100 %) Hue Fine 000–255 From low to high intensity (0–100 %) Saturation 000–255... -
Page 24: Ssp (8 Ch), Tour (13 Ch), Tr16 (20 Ch)
Performer Pendant 75 Q6 SSP (8 CH), TOUR (13 CH), TR16 (20 CH) 8 CH 13 CH 20 CH Function Value Setting (SSP) (TOUR) (TR16) Master Dimmer 000–255 From low to high intensity (0–100 %) Dimmer Fine 000–255 From low to high intensity (0–100 %) 000–255... - Page 25 Performer Pendant 75 Q6 8 CH 13 CH 20 CH Function Value Setting (SSP) (TOUR) (TR16) 191–195 Color 37 Light Pink 196–200 Color 38 Pretty'n Pink L794 201–205 Color 39 Follies Pink L328 206–210 Color 40 Magical Magenta L795 211–215...
-
Page 26: Cmy (8 Ch)
Performer Pendant 75 Q6 8 CH 13 CH 20 CH Function Value Setting (SSP) (TOUR) (TR16) 011–100 Reserved 101–110 Dimmer Off 111–120 Dimmer Mode 4 121–150 Reserved 151–160 1200 Hz 161–170 2400 Hz 171–180 4000 Hz 181–190 6000 Hz 191–200 25000 Hz 201–210... - Page 27 Performer Pendant 75 Q6 8 CH Function Value Setting (CMY) 166–170 Color 32 Daylight Blue L165 171–175 Color 33 Pale Lavender L136 176–180 Color 34 Surprise Pink L194 181–185 Color 35 Pale Violet L142 186–190 Color 36 Perfect Lavender L700 191–195...
-
Page 28: Rdm Information
Performer Pendant 75 Q6 RDM Information This device supports RDM. Refer to 6.4.2. Supported RDM PIDs for the Device for more information. RDM Details ● Responder ID: 29B4:0A1XXXXX ● Manufacturer's ID: Showtec (Highlite International B.V.) ● Manufacturer Label: Showtec ●... -
Page 29: Supported Rdm Pids For The Device
Performer Pendant 75 Q6 Supported RDM PIDs for the Device Parameter ID Value Required DISC_UNIQUE_BRANCH 0x0001 DISC_MUTE 0x0002 DISC_UN_MUTE 0x0003 COMMS_STATUS 0x0015 STATUS_MESSAGES 0x0030 STATUS_ID_DESCRIPTION 0x0031 CLEAR_STATUS_ID 0x0032 SUPPORTED_PARAMETERS 0x0050 DEVICE_INFO 0x0060 DEVICE_MODEL_DESCRIPTION 0x0080 MANUFACTURER_LABEL 0x0081 DEVICE_LABEL 0x0082 FACTORY_DEFAULTS 0x0090... -
Page 30: Troubleshooting
Performer Pendant 75 Q6 Troubleshooting This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts. Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage. -
Page 31: Maintenance
Performer Pendant 75 Q6 Maintenance Safety Instructions for Maintenance DANGER Electric shock caused by dangerous voltage inside Disconnect power supply before servicing or cleaning. Preventive Maintenance Attention Before each use, examine the device visually for any defects. Make sure that: ●... -
Page 32: Corrective Maintenance
Performer Pendant 75 Q6 Corrective Maintenance The device does not contain user-serviceable parts. Do not open the device and do not modify the device. Refer repairs and servicing to instructed or skilled persons. Contact your Highlite International dealer for more information. - Page 33 Performer Pendant 75 Q6 Disposal Correct disposal of this product Waste Electrical and Electronic Equipment This symbol on the product, its packaging or documents indicates that the product shall not be treated as household waste. Dispose of this product by handing it to the respective collection point for recycling of electrical and electronic equipment.
- Page 34 Performer Pendant 75 Q6 Product code: 33149...
- Page 35 Performer Pendant 75 Q6 Product code: 33149...
- Page 36 ©2022 Showtec...