FLASHFORGE 3D PRINTER Focus 8.9 Quick Start Manual
  1. Manuals
  2. Brands
  3. FLASHFORGE 3D PRINTER Manuals
  4. 3D Printers
  5. Focus 8.9
  6. Quick start manual

FLASHFORGE 3D PRINTER Focus 8.9 Quick Start Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
EN/CN-A02
Quick Start Guide
WARNING
This guide is only applicable to Flashforge Focus 8.9 3D printer
1. Please put on gloves while using photopolymer resin
to avoid direct contact with hands.
2. To ensure the printing quality, please don't open the
light shield unless it's necessary.
3. Unused photopolymer resin needs to be stored in a
dark, dry , and cool place.
4. Please clean the finished model with anhydrous alcohol.
5. Please ensure that the platform is installed correctly
and no items before operating to avoid damaging the
LCD screen.
Focus 8.9

Advertisement

Table of Contents
loading

Related Manuals for FLASHFORGE 3D PRINTER Focus 8.9

Summary of Contents for FLASHFORGE 3D PRINTER Focus 8.9

  • Page 1 4. Please clean the finished model with anhydrous alcohol. 5. Please ensure that the platform is installed correctly and no items before operating to avoid damaging the LCD screen. This guide is only applicable to Flashforge Focus 8.9 3D printer...
  • Page 2 Foreword Note Each 3D printer has undergone a printing test before leaving the factory. If there are residual consumables in the feed resin tank or slight scratches on the printing platform, it is normal and will not affect the use. Dear customer: Thank you for choosing and using the products of Flashforge Technology.
  • Page 3 Electrical Requirements Be sure to ground the device; do not modify the plug of the device. (Ungrounded/ incorrectly grounded/modified plugs will inevitably increase the risk of leakage) Do not expose the device to humidity and hot sun. (Wet environment will increase the risk of leakage/exposure will accelerate the aging of plastic parts) Do not abuse the power cord, and be sure to use the power cord provided by Flashforge.
  • Page 4 Getting To Know Your 3D Printer 1. Light Shield 2. Platform Tighten Knob 3. Z-axis 4. Leveller 5. Build Plate 7. Box Tighten Knob 8. LCD 6. Resin Box 9. Touched Screen 10. Ethernet 11. USB Stick Port 12. Power Slot 13.

  • Page 5: Accessory Box

    Accessory Box 3D Printer Power Cable Resin Box Quick Start Guide After-sales card Metal Scraper Plastic Scraper Build plate set Rubber Gloves USB Stick Wrench Set Filter Paper Wrench Set: Stamping wrench, Screw driver, Screws Build Plate set：Build plate, Leveller, Handle Resin Box Set：Resin Box, FEP Film, Film fixed frame, Box Tighten Knob...
  • Page 6 Leveling Open the paper box and take out the 3D printer on the desk. Remove all protective foam and plug in the power cable. 1. Install the build plate on the plate holder. 2. Tighten the platform tighten knob. 3. To loose the screws on both sides of 4.
  • Page 7 5. Connect the power adapter and power cable. Plug the output end of the power adapter into the power input port on the back of the printer and turn on the switch. Print Tool System Move Residue WLAN Stop Stop 6.
  • Page 8 lock the Press screws 8. Press the top of the build plate with one hand to let four corners of build plate to touch the LCD screen evenly. Pre-tighten the screws on both sides of the platform and then lock them separately during the process. Twitch paper and feel the resistance.

  • Page 9: First Printing

    First Printing 1. Make sure the LCD screen, build plate and 2. Tighten the knobs to fix the box. resin box is clear enough. Install the resin box on the LCD screen. 3. After confirm the installation of resin box 4.

  • Page 10: Post-Processing

    File list Model-01 Model-02 Model-03 Print Tool System Model-04 Dental Model 0 h 52 min 0.05 mm 5. Click the [Print] to enter the model list. Click the model file to star the printing. Note Do not open the top cover during printing to avoid eyes hurt. Post-processing Dental Model Print Completed...
  • Page 11 3. Remove the model via the metal scraper and clean the model in the cleaning box with anhydrous alcohol to wash off the excess resin. 4. After cleaning, dry the model via a dust-free cloth or an air gun. It would be better to solidify the model again via curing box.
  • Page 12 Replace the FEP film in the resin box Please refer to the following steps when install or replace the FEP film. 1. Loose the screws at the bottom of the 2. Align the FEP film with the screw holes resin box to remove the film fixing frame and clamp it between the two fixing and remove the overused FEP film.

  • Page 13: Software Operation

    Software Operation FlashDental FlashDental.exe Load 1. Install and run the FlashDental.exe program. 2. Click Load, select the model file. Print Set Position I want to: Preview Print When Slice Done 0.00mm Material Type: Dental Model Resin 0.00mm Save As New Remove Operation: 0.00mm...

  • Page 14: Maintenance

    Load the model files 1. Copy the ‘.svgx’ file to the USB stick on the computer. It would be better to remove USB stick from computer after ‘Safely Remove USB stick ’ note to avoid file damage. File list Model-01 Model-02 Model-03 Print...
  • Page 15 Follow us Zhejiang Flashforge 3D Technology Co., Ltd. Address: No.518 XianYuan Road, Jinhua City,Zhejiang Province, China Service Hotline: +86 579 82273989 support@flashforge.com...
  • Page 16 FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This manual is also suitable for:

Cn-a02

Table of Contents