Related Manuals for FLASHFORGE 3D PRINTER Artemis EN-A01
Summary of Contents for FLASHFORGE 3D PRINTER Artemis EN-A01
- Page 1 Artemis EN-A01 USER GUIDE This guide is only applicable to FLASHFORGE Artemis 3D printer...
-
Page 3: Table Of Contents
Content Notes Legal Statement Equipment Parameters Unpacking Chapter 1 Equipment Introduction 1.1 - Product Introduction 1.2 - Kit Contents Chapter 2 Preparation for Printing 2.1 - Assemble filament 2.2 - Build Plate 2.3 - Power On 2.4 - Leveling Build Plate 2.5 - Loading Filament 2.6 - Software Installation Chapter 3 First Print... -
Page 4: Notes
Notes Do not make any modifications to the printer. To avoid personal injury or property damage please ensure your operation followed by the Manual. Dress properly. Do not wear loose clothing or jewelry. Keeping your hair, clothing and gloves away from moving parts. Do not directly touch the nozzle and build plate to avoid high-temperature burn. -
Page 5: Equipment Parameters
Equipment Parameters Model Artemis Print volume 190*195*200mm Forming technology Extruder quantity Layer thickness 0.1mm-0.4mm Nozzle diameter Standard 0.4mm Print precision ±0.2mm Filament φ1.75mm PLA / PETG / TPU File format stl / obj / amf /3mf / fpp / bmp /png / jpg / jpeg Connectivity Internal memory printing / USB stick printing /W i-Fi connection printing Slicing software... -
Page 6: Unpacking
Unpacking Open the box, take out the user manual and the USB flash disk. Remove the foam. Lift the printer and put it on the desk, then take Artemis out of the plastic bag. Remove the top foam, there should be a power cable included. Take out the foam under nozzle. -
Page 7: Chapter 1 Equipment Introduction
Chapter 1 Equipment Introduction 1.1 Product Introduction Y-axis Guide Rail X-axis Guide Rail Z-axis Guide Rail Limit position assembly Glass platform Clip Leveling Nut Touch Screen USB Stick Input Power Voltage Switch LED Light Nozzle Turbofan Baffle Power Switch Power Input Spool installation port Filament detect sensor... -
Page 8: Kit Contents
1.2 Kit Contents EN-A01 Artemis USER GUIDE This guide is only applicable to FLASHFORGE Artemis 3D printer 3D Printer Power Cable Filament User Guide Material Rack Nozzle USB Flash Disk Remove Tool Needle Grease Flexible Spring Sheet Wrenches and Screwdrivers Glue... -
Page 9: Chapter 2 Preparation For Printing
Chapter 2 Preparation for Printing 2.1 Assemble filament Install the material rack on the back of printer. Press the handle Insert the filament into the intake, pull out the PTFE tube from extruder; Then press the handle to push filament into filament feeding roller. -
Page 10: Build Plate
2.2 Build Plate Artemis is installed with the glass platform by default, while users can also use the flexible removable platform. Glass platform: The bottom is flatter, but the removal of the model requires a scraper; If the glass platform is used when the ambient temperature is low, it is recommended to apply glue on it before printing to increase the adhesion. -
Page 11: Leveling Build Plate
2.4 Leveling Build Plate Click [settings]-[Language] to switch the language. How to use the nuts Build plate goes up Build plate goes down Rotate the nuts clockwise Rotate the nuts Anticlockwise Raise the build plate to reduce the distance Lower the build plate to increase the distance between the nozzle and build plate. - Page 12 Lightly pull the A4 paper and feel the friction. If the friction is too big to move, tap [↓] to increasethe distance between nozzle and build plate; if the friction is too small, tap [↑] to reduce the distance between nozzle and build plate. It is better that pull the paper to feel the significant frictional resistance until the slight scratches appear without damage.
-
Page 13: Loading Filament
2.5 Loading Filament Please ensure that the filament has been loaded in an appropriate Note approach. Tap [Control] - [Load]. It starts to load the filament when the targeted temperature reached. Do not stop loading when the nozzle extrudes the filament. It is suggested that extrude the filament evenly then tap [OK] to back to the homepage. -
Page 14: Chapter 3 First Print
Chapter 3 First Print Suggestions Ensure that the build plate has been leveled before printing. Please clean extruder before printing (Load the filament for a while to extrude all the melted filament you printed last time out of the extruder). Do not leave the printer unattended during operation. -
Page 15: Unloading Filament
3.2 Unloading Filament Please follow steps below if you need to unload filament in daily use. Tap [Control] - [Unload]. When the filament unload out of the filament feeding port, the unload operation is finished. After unload completed then load again, it is filament replacement. Note 3.3 Wi-Fi Connection... -
Page 16: Connect Printer By Wi-Fi
Tap [Settings] - [Wi-Fi], open the WIFI function. Choose the Internet and save the password. 3.4 Connect Printer by Wi-Fi 1. After the Wi-Fi connected successfully, tap [Info] and check the IP Address. 2. Open the FlashPrint 5, click [Print] - [Connect Machine], input the IP address and click the connect. -
Page 17: Firmware Upgrade
3.5 Firmware Upgrade Method 1: Get the firmware files: Connect with aftersales and send email to supports@flashforge-usa.com Copy the firmware into the blank USB flash disk. Plug in the USB flash disk into the USB port of printer and reboot the printer, waiting for the upgrade process finished. -
Page 18: Printing Notice
3.6 Printing Notice The adhesion of glass build plate may decrease after long time using. Please apply proper amount of glue to keep and improve the adhesion. Warping issues may occur when print ABS filament in cold environment, you may use glue to enhance the adhesion. -
Page 19: Chapter 4 Faq
Chapter 4 FAQ Q： What if the files are garbled and cannot be read? A： 1. The format of files after slicing is not compatible; 2. Repair the model before slicing. Q： What if the model warps or is unable to stick to the build plate? A：... - Page 20 Q： What if the axis cannot be moved? A： Check the wire of the electric motor. Q： What if the files on the USB flash disk cannot be identified? A： 1. Clean and wipe the USB flash disk; 2. Format the USB flash disk; 3.
-
Page 21: Chapter 5 Support And Service
Chapter 5 Support and Service Flashforge team is on standby and ready to help you with any challenges you may have with your 3D printer. If the issues or questions are not covered in this User Guide, you can seek for solutions on our official website or contact us via telephone. There are solutions and instructions to common issues that can be found in our knowledge base. - Page 24 Follow us FlashForge USA Address: 17747 Railroad Street, City of Industry, CA 91748 supports@flashforge-usa.com...