Subscribe to Our Youtube Channel
Related Manuals for Westermo Lynx DSS L108
Summary of Contents for Westermo Lynx DSS L108
- Page 1 User Guide 6643-2220 Lynx DSS L108 / L208-F2G-S2 WeOS Industrial Ethernet 8-port Device Server Switch www.westermo.com...
-
Page 2: Software Tools
Under no circumstances shall Westermo be responsible for any loss of data or income or any special, incidental, and consequential or indirect damages howsoever caused. -
Page 3: Maintenance
Maintenance No maintenance is required, as long as the unit is used as intended within the specified conditions. Agency approvals and standards compliance Type Approval / Compliance EN 61000-6-1, Immunity residential environments EN 61000-6-2, Immunity industrial environments EN 61000-6-3, Emission residential environments EN 61000-6-4, Emission industrial environments EN 55022 +A1, Emission IT equipment EN 55024 +A1 + A2, Immunity IT equipment... -
Page 4: Declaration Of Conformity
Declaration of Conformity Westermo Teleindustri AB Declaration of conformity The manufacturer Westermo Teleindustri AB SE-640 40 Stora Sundby, Sweden Herewith declares that the product(s) Type of product Model Ethernet device server switch Lynx DSS L*08-F2G-S2* is in conformity with the following EC directive(s). -
Page 5: Product Description
Product description Status Active Ports 6 x RJ-45, 10/100BaseT. 4 x SFP, 100/1000 Mbit/s. 2 x RJ-45, RS-232/422/485. Description Managed Device Server Switch with routing functionality Warranty period 5 years Approvals Marine DNV Standard for Certification no. 2.4 EMC (Electromagnetic Compatibility) EN 61000-6-1 Immunity residential environments EN 61000-6-2... - Page 6 EN 61000-4-9, 300 A/m pulsed magnetic field EN 61000-4-3, 20 V/m @ (80 – 2700) MHz radiated RF immunity 1 kHz sine, 80% AM EN 61000-4-6, Power port: 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz conducted RF immunity Ethernet: 10 V, 80% AM, 1 kHz;...
- Page 7 Mechanical IEC 60068-2-6, IEC 60068-2-6,(sine), operating vibration 3 – 13.2 Hz: 1mm 13.2 – 100 Hz: 0.7 g 5.5 – 30 Hz: 1.5 g 30 – 50 Hz: 0.42 mm 50 – 500 Hz: 4.2 g IEC 60068-2-64 (random), operating 5 –...
- Page 8 Interface specifications, 100/1000SFP Optical/Electrical specification IEEE std 802.3. 2005 Edition Data rate 100 Mbit/s or 1000 Mbit/s transceivers supported Duplex Full or Auto, depending on transceiver Transmission range Depending on tranceiver Connection SFP slot holding fibre transceiver or copper transceiver Number of ports 1 or 2 Interface specifications, RS-232...
-
Page 9: Sfp Transceivers
Data rate 115.2 kbit/s Data format 8 data bits, no parity, 1 stop bit, no flow control Circuit type SELV Connection 2.5 mm jack, use only Westermo cable 1211-2027 Accessories Description Art no Westermo console cable 1211-2027 RJ45 to terminal block... -
Page 10: Location Of Interface Ports And Led's
Location of interface ports and LED’s LED Indicators (for details see page 14) Power connection (for details see page 7 and 13) Position Direction Description No. 1 VBUS No. 2 In/Out D– No. 3 In/Out No. 4 Shield In/Out Connected to protective earth SFP transceivers (for details see page 9) Ethernet connection TX (4 ports) Position... - Page 11 RS-422/485 (for more details see below) Position Signal Direction Description RS-422 RS-485 (4-wire) (2-wire) No. 1 T+/R+ Out/In RS-422: Transmit RS-485: Transmit/Receive No. 2 T– T–/R– Out/In RS-422: Transmit RS-485: Transmit/Receive No. 3 R– – RS-422: Receive No. 4 – –...
-
Page 12: Connection To Console Port
The following steps needs to be taken 1. Connect the serial diagnostic cable to the console port (use only Westermo cable 1211-2027). 2. Connect cable to your computer (USB port, if drivers are needed they can be downloaded from our Web page). -
Page 13: Power Connection
Power connection 4-position Product marking Direction Description No. 1 +DC1 Input Supply voltage input DC1 No. 2 +DC2 Input Supply voltage input DC2 No. 3 -COM Input Common No. 4 -COM Input Common LynxDSS supports redundant power connection. The positive inputs are +DC1 and +DC2, the negative input for both supplies are –COM. -
Page 14: Led Indicators
LED indicators Status Description Unit has no power. GREEN All OK, no alarm condition. Alarm condition, or until unit has started up. (Alarm conditions are configurable, see ''WeOS Management Guide''). BLINK Location indicator ("Here I am!"). Activated when connected to IPConfig Tool, or upon request from Web or CLI. - Page 15 Mounting This unit should be mounted on 35 mm DIN-rail, which is horizontally mounted inside an apparatus cabinet or similar. It is recommended that the DIN-rail is connected to ground. Snap on mounting, see figure. Mounting Lynx with integrated DIN-clip: Removal Removing Lynx with integrated DIN-clip: Press down the support at the back of the unit using a screwdriver.
-
Page 16: Getting Started
• IPConfig tool This is a custom Westermo tool used for discovery of attached Westermo units. Note! Version of IP Config tool must be 10.4.0 or higher. • Web Configuration of the unit using the web browser. -
Page 17: Referring Documents
Referring documents Type Description Document number Management Guide Westermo OS management guide 6101-3201 Factory default on Lynx DSS It is possible to set the unit to factory default settings by using two straight standard Ethernet RJ-45 cables. 1. Power off the switch and disconnect all Ethernet cables (copper and fibre). -
Page 20: Sales Units
Other Offices infos@westermo.fr sales@westermo.com.sg www.westermo.fr www.westermo.com Germany Sweden info@westermo.de info.sverige@westermo.se www.westermo.de www.westermo.se For complete contact information, please visit our website at www.westermo.com/contact or scan the QR code REV.G 6643-2220 2015-01 Westermo Teleindustri AB, Sweden – A Beijer Electronics Group Company...
Need help?
Do you have a question about the Lynx DSS L108 and is the answer not in the manual?
Questions and answers