Table of Contents
Advertisement
S
S
S
UPER
TORAGE
YSTEM 6028R-E1CR12N User's Manual
1-2
Serverboard Features
The 6028R-E1CR12N is built around the X10DRi-T4+, a dual processor serverboard
based on the Intel C612 chipset. Below are the main features of the X10DRi-T4+.
(See Figure 1-1 for a block diagram of the chipset.)
Processors
The X10DRi-T4+ supports single or dual Intel® Xeon E5-2600 (v3/v4) Series pro-
cessors. Please refer to the serverboard description pages on our web site for a
complete listing of supported processors (www.supermicro.com).
Memory
The X10DRi-T4+ has 24 DIMM slots that can support up to 3 TB of ECC LRDIMM
(Load Reduced DIMMs) or 1.5 TB of ECC RDIMM (Registered DIMMs) DDR4-
2400/2133/1866/1600 memory. See Chapter 5 for details.
Main Storage Controller
An LSI 3108 controller card is included in the system to support up to 240 SATA
3.0/SAS 3.0 hard drives. (RAID 0, 1, 5, 6, 10, 50 and 60 supported). The SATA/
SAS drives are hot-swappable units.
Serial ATA
A SATA controller is also integrated into the chipset to provide 10 SATA 3.0 (6/Gbps)
ports (I-SATA0-5 supported by Intel PCH and S-SATA0-3 supported by Intel SCU),
which are RAID 0, 1 and 10 supported. The SATA drives are hot-swappable units.
RAID 5 supported with Windows OS only).
Note: The operating system you use must have RAID support to enable the hot-
swap capability and RAID function of the SATA drives.
PCI Expansion Slots
The X10DRi-T4+ has three PCI-Express 3.0 x8 slots (CPU2 Slot1/Slot2/Slot6), two
PCI-Express 3.0 x16 slots (CPU1 Slot3/ CPU2 Slot5) and one PCI-Express 2.0 x4
in x8 slot (CPU2 Slot4).
Rear I/O Ports
The I/O ports include one COM port, a VGA port, four USB (two USB 3.0 and two
USB 2.0), four 10G (TLAN) Ethernet ports and a dedicated IPMI LAN port.
1-2
1-3
Server Chassis Features
The SC826BE1C-R920LP is an 2U form factor chassis designed to be used in a
storage configuration. The following is a general outline of the main features of the
SC826BE1C-R920LP chassis.
System Power
The SC826BE1C-R920LP features a redundant, hot-plug 920W power supply com-
posed of two separate power modules. This power redundancy feature allows you
to replace a failed power supply without shutting down the system.
Hard Drive Subsystem
The SC826BE1C-R920LP chassis was designed to support 12 hot-swap SAS/
SATA hard drives. An optional, internal fixed drive mounting bracket (MCP-220-
82611-0N) may be added to support two 2.5" SATA drives.
Front Control Panel
The control panel on the SC826BE1C-R920LP provides you with system monitor-
ing and control. LEDs indicate system power, HDD activity, network activity, system
overheat and power supply failure. A main power button and a system reset button
are also included.
Cooling System
The SC826BE1C-R920LP chassis includes three 8-cm hot-plug system cooling fans
located in the middle section of the chassis. An air shroud channels the airflow from
the system fans to efficiently cool the processor area of the system. Each power
supply module also includes a cooling fan.
Chapter 1: Introduction
1-3
Advertisement
Table of Contents
