Page 1 sales@artisantg.com artisantg.com (217) 352-9330 | Visit our website - Click HERE...
Page 2 MPS 200/800 Administrator Guide !" Join up to 40/160 video and 32/48 audio sites in one or more conferences !" 19” rack-mountable chassis with LCD in front and CompactPCI backplane !" Wide range of network and protocol support: SIP, IP, ISDN and V.35 !"...
Page 3 Conference status, the Change tab ......64 MPS 200 with 2 Media Processing Boards....20 The Gateway ..............65 MPS 200 with ISDN and V.35 Network Cards ....21 Gateway Features ............65 MPS 800 with 8 Media Processing Cards ..... 22 Gateway Capacity ............
Page 4 Configuration using XML ..........110 MPS 800–Inserting additional network interface cards ..155 Certificate Management ..........111 MPS 200–Inserting additional network interface cards ..156 About the Quality of Service (QoS) feature ....... 157 Gateway configuration About video features ............158 Gateway Functionality and Dialling Rules ......
Page 5 Chapter 1 Introduction Thank you for choosing TANDBERG! In this chapter... The TANDBERG MPS enables sites on IP, ISDN What’s new in version J4.5 and High Speed Serial to participate in meet- Disclaimer ings with each other and offers superior quality...
Page 6 See the MPS API guide for a complete overview of the MPS or via Telnet, SSH or Serial Port at /var/log/messages while logged in as root. API commands. The TANDBERG MPS API Guide is found at the TANDBERG web site. Go to: http://www.tandberg.com/docs...
Page 7 License Agreement All rights reserved. This document contains information that is proprietary to TANDBERG. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, electronically, mechanically, by photocopy- ing, or otherwise, without the prior written permission of TAND- BERG.
Page 8 Amended / Expanded Copyright notices for third- All or some portions of this file are derived from ;=56?@6"ABC":,-.(DD)1($/-"E8;FD,.(1-(*"-$4&%)'(" party software on the TANDBERG MPS systems are material licensed to the University of California 5. Products derived from this software may not be...
Page 9 MPS 200/800 Administrator Guide Contents Introduction Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Third Party Software, Licenses and Copyright, cont... This library is free for commercial and non-com- IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,...
Page 10 MPS 200/800 Administrator Guide Contents Introduction Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Third Party Software, Licenses and Copyright, cont... 8)'&"L 8)'&"N 8)'&"O Redistribution and use in source and binary forms,...
Page 11 MPS 200/800 Administrator Guide Contents Introduction Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Third Party Software, Licenses and Copyright, cont... This code is based on code written by Patrick Powell...
Page 12 MPS 200/800 Administrator Guide Contents Introduction Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Third Party Software, Licenses and Copyright, cont... !" Lafayette, Indiana 47907. All rights reserved. README file under the THANKS section.
Page 13 MPS 200/800 Administrator Guide Contents Introduction Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Third Party Software, Licenses and Copyright, cont... !" Redistributions of source code must retain the The above copyright notice and this permission...
Page 14 MPS 200/800 Administrator Guide Contents Introduction Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Safety Instructions For your protection please read these safety Lightning Servicing Product Approvals instructions completely before you connect...
Page 15 European RoHS Digital User Guides Directive (2002/95/EC) and the European WEEE TANDBERG’s environmental objectives are to: TANDBERG is pleased to announce that we have Directive (2002/96/EC). !" Develop products that reduce energy replaced the printed versions of our user guides...
Page 16 MPS 200/800 Administrator Guide Contents Introduction Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us China RoHS Table D14033.10—APRIL 2009...
Page 17 Up to 160 video sites and 48 telephony calls The TANDBERG MPS 200 can support up to ces > Distributed MCUs for details. and up to 20 Gateway calls on the MPS 200. with the MPS 800 and up to 40 video sites !"...
Page 18 !" 1 X LAN / Ethernet (RJ-45) 10/100 Mbit on able. MPS 200, there is support for up to 2 Media Pro- the front. See the Appendices section for further details of !" On the front of the chassis is a Liquid Crystal cessing Boards.
Page 19 MPS 200 with 2 Media Processing Boards tion using LCD. You will also find pictures of MPS 200 with ISDN and V.35 Network Cards the MPS 800 and MPS 200 with a description of the interfaces. MPS 800 with 8 Media Processing Cards The Quick Setup will help you get your MPS MPS 800 with ISDN and V.35 Network Cards...
Page 20 !" This product complies with directives: LVD 73/23/EC and EMC 5. Cables: 89/366/EEC. The TANDBERG MPS comes with 4 screws and 4 nuts for mount- Power cable a. !" ing in standard 19” racks. The chassis is equipped with brackets.
Page 21 Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us System overview MPS 200 with 2 Media Processing Boards Use Arrow keys to navigate in the menu Display Enter/OK key Brackets for Rack Mounting Screw holes for...
Page 22 Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us System overview, cont... MPS 200 with ISDN and V.35 Network Cards LEDs for Bracket for Rack V.35 E1/T1 E1/T1 Mounting (in front) RS232 Line 1-8...
Page 23 MPS 200/800 Administrator Guide Contents Introduction Getting started Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us System overview, cont... MPS 800 with 8 Media Processing Cards LEDs for Use Arrow keys to Display...
Page 24 MPS 200/800 Administrator Guide Contents Introduction Getting started Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us System overview, cont... MPS 800 with ISDN and V.35 Network Cards 2 V.35 Serial Interface Cards 2 PRI E1/T1 ISDN Net-...
Page 25 Connect to Two Separate IP Networks Do not use a hub! If you want to connect the TANDBERG MPS to two separate Use a switch/router and not a hub IP networks you must use the second ‘Enet2’ interface on...
Page 26 Contact us Starting up the system MPS200 Front Side MPS200 Back Side Preparations Liquid Crystal Before starting the TANDBERG MPS make sure Display the following has been done: System Controller Board must be 1. installed in the first slot in the chassis.
Page 27 MPS 200/800 Administrator Guide Contents Introduction Getting started Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us The LCD interface LCD - Liquid Crystal Display Example of the LCD menu structure on a MPS having 1 System Controller Board and 2 Media Processing Boards:...
Page 28 Appendices Contact us System Controller Board Initial Configuration Parameter Configuration " Before using the TANDBERG MPS it requires !" Press any key to open the main menu. Arrow SC IP Config Arrow buttons to select a line and set the buttons to select some basic configuration.
Page 29 - Configuration of the Media : Defines the static IP address of After configuring the IP-address of the System Controller Board(s) and Media Processing Processing Board (MPS 200 having 1-2 boards the Media Processing Board: Example Controller Board (and restart the MPS), you Board(s).
Page 30 Gateway option is installed. SSH and Telnet The TANDBERG MPS can also be controlled via SSH or Telnet by using a comprehensive set of API commands. This enables the TANDBERG MPS to be controlled by a different user...
Page 31 If applicable, set the IP Address Interface 2 As a minimum you must configure Interface 1. If your TANDBERG MPS is connected to two different IP networks, you must configure both Interface 1 and Interface 2. For further information, go to: System Configu- ration >...
Page 32 MPS 200/800 Administrator Guide Contents Introduction Getting started Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Quick setup, cont... 5'/-&=7&>4?=?&:#*;2<1!'(#* Configuration of the MPS using Web Interface Open a web browser and type in the IP address to access the web interface.
Page 33 MPS 200/800 Administrator Guide Contents Introduction Getting started Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Quick setup, cont... 5'/-&?7&9@8&:#*;2<1!'(#* Configuration of the MPS using Web Interface Open a web browser and type in the IP address to access the web interface.
Page 34 MPS to know which conference number to dial into. !" ISDN Number. The ISDN number must be a valid PRI number of the TANDBERG MPS at hand. !" E.164 Alias. The H.323 E.164 numeric alias for each conference.
Page 35 Manage an active conference Stay up-to-date Conference Status, Add Participants, Examples, We recommend you visit the TANDBERG web Edit Conference Configuration, Dial-In Configura- site regularly for an updated version of this tion, The Basic tab, The Advanced tab, The Termi- guide.
Page 36 32. !" Video Calls 0 of 40: indicate that 0 video calls are connected to the TANDBERG MPS. The total number of supported video calls in this configuration is maximum 40. !"...
Page 37 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us MCU Conference Overview Filter Conference Overview Create a Conference Password For privacy, a conference !" Active If selected all the active confer- can be password protected.
Page 38 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Create a conference on the MCU Overview Select the tab and Create a new conference [Create] 1. ...
Page 39 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Create conference :#*0/1/*)/&:#*;2<1!'(#* Name The conference name will be shown on the Conference Over- view page and on the Conference Status page.
Page 40 Conference Over- and return to the All calls in this conference will be associated with this billing code. This will view page. allow management tools, such as the TANDBERG Management Suite, to use the code for billing purposes. D14033.10—APRIL 2009...
Page 41 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Create conference, cont... Video, Conference Layout Voice Switched 2 Split 3 Split 4 Split 4 + 3 Split...
Page 42 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Create conference, cont... Video settings CP Autoswitching The CP Autoswitching enables you to swap non speaking sites with the least active sites in the picture.
Page 43 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Create conference, cont... Video settings Dual Video Stream The MCU supports DuoVideo , H.239 and BFCP. Set to On to enable a Dual Video Stream protocol for this conference.
Page 44 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Create conference, cont... Video settings Participant Identifier Auto: Set to Auto to let the System Name of a participant to be displayed the number of seconds set in Participant Identifier Timeout.
Page 45 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Create conference, cont... Video settings Optimal Voice Switch Set to On to enable Optimal video format in Voice Switch mode, if the connected endpoints allows this.
Page 46 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Create conference, cont... Audio settings Voice Switch Timeout Defines the number of seconds between 1 and 10, a partici- pant must speak before it gets the speaker indication and is shown as the speaker to the other endpoints.
Page 47 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Create conference, cont... Security settings Password To ensure only authorized participants are able to join this con- ference you can set a password.
Page 48 Security settings Encryption When set to On all participants in the conference must support DES or AES encryption (available on all TANDBERG endpoints using software version B4.0 or later). Participants not supporting encryption will be shown the ‘Encryption Required’ screen for 60 seconds before they are disconnected from the conference.
Page 49 Advanced Video Option ports for this conference. Values: 0 - 40 for MPS 200 and 0 - 160 for MPS 800. Telephone Participant Limit Defines the maximum number of Telephone Participants al- lowed in the conference.
Page 50 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Create conference, cont... Network settings Network Bandwidth Management If a conference participant is experiencing poor network quality it will send Fast Update Requests (FUR) to the...
Page 51 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Manage an active conference Frequently used numbers can be stored in the Phone Book or a management system, e.g. TAND- BERG Management Suite (TMS).
Page 52 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Overview MCU Conference Status The Conference Status page shows information about a confer- ence and lets you control the conference.
Page 53 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Overview MCU, cont... Conference Status The Conference Status page shows information about a confer- ence and lets you control the conference.
Page 54 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Overview MCU, cont... Add Participants The Conference Status page shows information about a confer- ence and lets you control the conference.
Page 55 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Overview MCU, cont... Add Participants The Conference Status page shows information about a confer- ence and lets you control the conference.
Page 56 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Overview MCU, cont... Add Participants The Conference Status page shows information about a confer- ence and lets you control the conference.
Page 57 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Add Participants - Examples Example with H.323/IP (H.323 ID): Example with H.323/IP (IP Address): Example with ISDN: Example with G.703 Leased Line:...
Page 58 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Overview MCU, cont... CD('&:#*0/1/*)/&:#*;2<1!'(#*& The Conference Status page shows information about a confer- ence and lets you control the conference.
Page 59 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Overview MCU, cont... B(!",8*&:#*;2<1!'(#*& The Conference Status page shows information about a confer- ence and lets you control the conference.
Page 60 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Overview MCU, cont... Conference status, the Basic tab The Conference Status page shows information about a confer- ence and lets you control the conference.
Page 61 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Overview MCU, cont... Conference status, the Basic tab The Conference Status page shows information about a confer- ence and lets you control the conference.
Page 62 To assign the floor to a participant, press the button. To mute the loadspeaker of a participant, press the To add a participant to the TANDBERG MPS Phone Mute Loudspeaker Phone Book The participant is then transmitting video to all the other partici-...
Page 63 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Overview MCU, cont... Conference status, the Advanced tab The Conference Status page shows information about a confer- ence and lets you control the conference.
Page 64 By simply dialling from one TANDBERG MPS to other TANDBERG MPSs one will achieve a distributed setup. Master/Slave The TANDBERG MPS dialling out will be defined as the Master MCU. All other MCUs will be defined as Slave MCUs. Read about cascaded MCUs in the Distributed MCUs chapter in the Appendices section.
Page 65 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Overview MCU, cont... Conference status, the Change tab The Conference Status page shows information about a confer- ence and lets you control the conference.
Page 66 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us The Gateway Gateway Features Gateway Capacity Far End Camera Control using H.224 (H.281) Far End Camera Control using H.224 (H.281) al- Each Media Board can support up to 7680 kbps of total bandwidth.
Page 67 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Gateway Usage Information The Usage pane for Gateway calls shows each active call through the Gateway (Load, ISDN channels and number of calls).
Page 68 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Gateway Calls Overview Actions When a call is active, the Administrator or Operator can disconnect the call, or transfer the call from one IP endpoint to another.
Page 69 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Disconnect a Gateway call Actions - When a call is active the Administrator or Operator can Disconnect...
Page 70 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Transfer a Gateway call Actions - When a call is active the Administrator or Operator can Disconnect...
Page 71 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us The Phone book Phonebook Select the Number of Entries There is support for: !" Up to 250 local entries in the phone book.
Page 72 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us The Phone book, cont... My Contacts, Add New Entry Name Enter the name of the phone book entry.
Page 73 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us The Phone book, cont... My Contacts, Edit New Entry Name Enter the name of the phone book entry.
Page 74 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us The Phone book, cont... Add Group Entry Group Entry The Group entries are useful for recurring meetings where the same participants meet each time.
Page 75 G.703 Board Status Serial V.35 Board Status Media Board IP Status Stay up-to-date H.323 Status We recommend you visit the TANDBERG web SIP Status site regularly for an updated version of this guide. Go to: http://www.tandberg.com/docs System Information D14033.10—APRIL 2009...
Page 76 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System status System configuration Gateway configuration MCU configuration Appendices Contact us H.320 Board Status H.320 Status The H.320 Status shows the system clock port, rate, state and type.
Page 77 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System status System configuration Gateway configuration MCU configuration Appendices Contact us ISDN PRI Board Status ISDN PRI Board Status If a PRI cable is disconnected or malfunctioning, or basic configuration is erroneous, !"...
Page 78 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System status System configuration Gateway configuration MCU configuration Appendices Contact us G.703 Board Status G.703 Board Status This page gives status information about avail- able channels and which calls are connected and recently disconnected.
Page 79 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System status System configuration Gateway configuration MCU configuration Appendices Contact us Serial V.35 Board Status Serial V.35 Board Status Clock rate: Displays the current clock rate for each individual Serial port.
Page 80 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System status System configuration Gateway configuration MCU configuration Appendices Contact us Media Board IP Status Media Board IP Status Red alarm indicates the Ethernet interface on the Media Board is down.
Page 81 MCU configuration Appendices Contact us H.323 Status IP Address Shows the IP address of the TANDBERG MPS con- figured for Network #1. H.323 Gatekeeper Status Shows status and IP address of the Gatekeeper for Network#1, which the TANDBERG MPS is registered !"...
Page 82 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System status System configuration Gateway configuration MCU configuration Appendices Contact us SIP Status Mode - Shows if the SIP service is enabled or not. Server Status Show status towards the configured SIP server i.e. whether or not the MPS can find a server.
Page 83 Appendices Contact us System Information System Unit !" Product Type - Shows the TANDBERG product type !" Product ID - Shows the TANDBERG product id !" Up Time in Seconds - Shows the uptime since last boot in seconds !"...
Page 84 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System status System configuration Gateway configuration MCU configuration Appendices Contact us System Information , cont... MCU Resources !" Conference - Shows the total number of conferences available on the MPS !"...
Page 85 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System status System configuration Gateway configuration MCU configuration Appendices Contact us System Information , cont... Total !" Conference - Shows the total number of conference used on the MPS !"...
Page 86 H.320 Board Configuration the MPS. PRI Board Configuration G.703 Board Configuration Stay up-to-date IP Configuration We recommend you visit the TANDBERG web Media Board Configuration site regularly for an updated version of this Serial V.35 Board Configuration guide. Go to: http://www.tandberg.com/docs H.323 Configuration...
Page 87 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us >4?=E&F#!1D&:#*;2<1!'(#* Network Type must correspond with configurations set in the PRI Board Configuration if you have a PRI card or the G.703 Board Configuration...
Page 88 The TANDBERG MPS will not send <Sending Com- plete> (Default: Off). Send Number The TANDBERG MPS will send its own number to the far end. This is only useful when each conference have specified a Dial In number (Default: On).
Page 89 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us 9@8&F#!1D&:#*;2<1!'(#* , cont... PRI Board Configuration, Slot 1–n Network Type must correspond with configurations set in the...
Page 90 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us 9@8&F#!1D&:#*;2<1!'(#* , cont... PRI Board Configuration, Slot 1–n Network Type must correspond with configurations set in the...
Page 91 (default) If set to on, the PRI interface (IF #) is enabled. If set to off, the PRI interface (IF #) is disabled. Max Channels Indicates the maximum number of B-channels the TANDBERG MPS is allowed to use for each of the PRI-interfaces. !"...
Page 92 Specifies where the TANDBERG MPS will start searching for available B-channels for each PRI-line for an outgoing call. High: If set to High, the TANDBERG MPS will start to search for available B-channels at the highest numbered B-channel (De- fault: High)
Page 93 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us 9@8&F#!1D&:#*;2<1!'(#* , cont... PRI Board Configuration, PRI Interface 1–n - continued: PRI Board Configuration Network Type...
Page 94 If set to Off, the E1 CRC4 is disabled. If your network equipment does not support this feature, turn it Off. T1 Cable Length Specifies the cable length between the TANDBERG MPS and the CSU for each of the PRI lines (only valid for T1 networks). Possible values are: !"...
Page 95 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us G4HE?&F#!1D&:#*;2<1!'(#* PRI Board Configuration Ensure that Network Type is set to G.703 for the connected ISDN cards in the PRI Network Configuration G.703 Board...
Page 96 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us G4HE?&F#!1D&:#*;2<1!'(#* , cont... PRI Board Configuration Ensure that Network Type is set to G.703 for the connected...
Page 97 100Full: The MCU will connect to the LAN using 100 Mbps/ Full Duplex. If forcing the TANDBERG MPS to anything other than Save - Press the Save button to save changes. Auto then the Ethernet switch must also be forced to Restart - For the settings to take effect the unit must be restarted after pressing the Save button.
Page 98 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us 89&:#*;2<1!'(#* , cont... DNS Interface 1 and 2 - continued: IP Configuration DNS Server defines the network addresses for DNS servers, interface 1 and 2.
Page 99 The MCU will connect to the LAN using 100 Mbps/ Full Duplex. Save - Press the Save button to save changes. If forcing the TANDBERG MPS to anything other than Auto then the Ethernet switch must also be forced to match. NOTE:...
Page 100 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us 5/1(!"&J4?K&F#!1D&:#*;2<1!'(#* Slot (1 to n) Select Slot to configure the Serial V.35 Board(s). The picture shows that Serial V.35 Boards installed on Slot 2.
Page 101 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us 5/1(!"&J4?K&F#!1D&:#*;2<1!'(#* , cont... Slot (1 to n) Select Slot to configure the Serial V.35 Board(s). The picture shows that Serial V.35 Boards installed on Slot 2.
Page 102 Net 2 When dialling directly in to a conference from H.323, this requires the use of H.323 numbers. To achieve this the TANDBERG MPS must be registered to a Gatekeeper. Gatekeeper: Set Gatekeeper to Gatekeeper to enable the MPS to register to a Gatekeeper.
Page 103 - Press the Save button to save changes. System Contact Used to identify the system contact via SNMP tools such as TANDBERG Management Suite or HPOpenView. SNMP Host IP Address (1-3) Identifies the IP-address of the SNMP manager. System Location !"...
Page 104 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us 589&:#*;2<1!'(#* SIP Mode NOTE: The DNS must be configured on the IP configuration page when using SIP Set the SIP mode to On to enable the system for incom- ing and outgoing SIP calls.
Page 105 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us M#5&NM<!"('.&#0&5/1O()/P&:#*;2<1!'(#* QoS Configuration (network 1-2) The network must support Quality of Service (QoS) for these settings to work. You can configure the Quality of Service mode differently for Network #1 and Network #2.
Page 106 Appendices Contact us I(%)/""!*/#<%&:#*;2<1!'(#* Configuration - System name To change the System Name of the TANDBERG MPS, enter the new system name in the <System Name> field. Services The IP services can be independently disabled to prevent access to the TANDBERG MPS.
Page 107 Appendices Contact us Software Upgrade Software Upgrade New software to the TANDBERG MPS can be installed via the Software Upgrade web page. The Software Upgrade page shows the current software ver- sion, the hardware serial number and the installed options and the option keys.
Page 108 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us Q!*2<!2/R&5/'&Q!*2<!2/&!*D&Q!*2<!2/&;"/% Set Language The Set Language allows you to view and change the lan- guage in the web interface and dialogs.
Page 109 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us Language, Files.., Dialog pictures File Management The File Management allows viewing and changing pictures, sounds and symbols, which are shown to the participants when connecting to, and during a conference on the MPS.
Page 110 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us Language, Files.., Dialog Sounds and Symbols File Management The File Management allows viewing and changing pictures, sounds and symbols, which are shown to the participants when connecting to, and during a conference on the MPS.
Page 111 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us :#*;2<1!'(#*&<%(*2&SIQ XML Document The XML Uploading page, allows administrators to upload multiple configuration changes to the MPS instead of manu- Example: Text is copied from the command.xml file and pasted into the XML Document editor field.
Page 112 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration !"#$%&'()*+ ',-./$0)* MCU configuration Appendices Contact us :/1'(;)!'/&I!*!2/3/*' Manage Certificates Allows an administrator to upload X.509 certificates for use with HTTPS. These certificates can be created from any...
Page 113 The Gateway Configuration section contains In this chapter... information about how to configure and use the Gateway Functionality and Dialling Rules Gateway on the TANDBERG MPS. Reading this section makes you familiarize yourself with the Gateway Configuration configuration menu and functions important for...
Page 114 3. The user of a video conferencing system Example with IVR + TCS-4: sions for the MPS 800. For MPS 200 the maximum have a common number range, see enters the extension (H.323 E.164 Alias) Trunk Groups in the PRI Board Configu- is 20 sessions.
Page 115 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration 1/$%2/"'()*+ ',-./$0)* MCU configuration Appendices Contact us G!'/$!.&:#*;2<1!'(#* Dialling Rules Add new Dialling Rule Configure the new Dialling Rule from the row on 1. ...
Page 116 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration 1/$%2/"'()*+ ',-./$0)* MCU configuration Appendices Contact us G!'/$!.&:#*;2<1!'(#*R cont... Examples of dialling rules with ISDN Gateway Example with DID Example with IVR-TCS4 Example with DID:...
Page 117 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration 1/$%2/"'()*+ ',-./$0)* MCU configuration Appendices Contact us G!'/$!.&:#*;2<1!'(#*R cont... Examples of dialling rules with V.35 Gateway V.35 Ports Example with DID: Example with DID (V.35 to H.323) Example with DID: To address the V.35 ports in a dialling rule, the...
Page 118 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration 1/$%2/"'()*+ ',-./$0)* MCU configuration Appendices Contact us G!'/$!.&:#*;2<1!'(#*R cont... Examples of dialling rules with G.703 Gateway G.703 Ports: Example with DID: Example with DID: Example with DID: To address the G.703 ports in a dialling rule...
Page 119 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration 1/$%2/"'()*+ ',-./$0)* MCU configuration Appendices Contact us G!'/$!.&:#*;2<1!'(#*R cont... Gateway Settings Interoperability Experience has shown that some features - even though they are standardized - might cause interoperability problems with legacy video conferencing products.
Page 120 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration 1/$%2/"'()*+ ',-./$0)* MCU configuration Appendices Contact us G!'/$!.&:#*;2<1!'(#*R cont... Gateway Settings Interoperability Experience has shown that some features - even though they are standardized - might cause interoperability problems with legacy video conferencing products.
Page 121 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration 1/$%2/"'()*+ ',-./$0)* MCU configuration Appendices Contact us G!'/$!.&:#*;2<1!'(#*R cont... Gateway Settings Interoperability Experience has shown that some features - even though they are standardized - might cause interoperability problems with legacy video conferencing products.
Page 122 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration 1/$%2/"'()*+ ',-./$0)* MCU configuration Appendices Contact us G!'/$!.&:#*;2<1!'(#*R cont... Gateway Settings Interoperability Experience has shown that some features - even though they are standardized - might cause interoperability problems with legacy video conferencing products.
Page 123 The MCU Configuration section contains In this chapter... information about how to configure and use MCU Configuration the MCU on the TANDBERG MPS. Reading this section makes you familiarize yourself with the The Dial-In Numbers menu overview configuration menu and functions important for...
Page 124 The TANDBERG MPS 800 (200) supports up to 40 Personal Conferences (10) simultaneous conferences. The Personal Conferences enables...
Page 125 ISDN: The ISDN Single Dial In Number must be a valid PRI number of the TANDBERG MPS at hand. The IP address for Single Dial In Number must be a valid IP address on the TANDBERG MPS System Controller Card.
Page 126 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration 345'()*+ ',-./$0)* Appendices Contact us I:Y&:#*;2<1!'(#*R cont... The AdHoc Conferences menu Single Dial In Number allows the MPS to set up multiple conferences, in an Ad Hoc manner.
Page 127 The prefix will be registered on the connected Gatekeeper. conference. each conference. each conference. (DID - Dial In Direct) The TANDBERG MPS must be registered to The TANDBERG MPS must be The TANDBERG MPS must be a Gatekeeper. registered to a Gatekeeper.
Page 128 (beta) is removed from the web interface. Works with conference. each conference. each conference. F7.x and TANDBERG GW MultiWay (beta) only. The setting is still available from the API using the command: The TANDBERG MPS must be registered to The TANDBERG MPS must be...
Page 129 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration 345'()*+ ',-./$0)* Appendices Contact us I:Y&:#*;2<1!'(#*R cont... The Personal Conferences menu Personal Conferences allows you to specify one or more conferences with: !"...
Page 130 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration 345'()*+ ',-./$0)* Appendices Contact us I:Y&:#*;2<1!'(#*R cont... The Personal Conferences menu Personal Conferences allows you to specify one or more conferences with: !"...
Page 131 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration 345'()*+ ',-./$0)* Appendices Contact us I:Y&:#*;2<1!'(#*R cont... The Direct AdHoc Conferences menu Direct Ad Hoc conference is an alternative to Personal Conferences and the traditional Ad Hoc conferences.
Page 132 WX/&L/'$#1+&91#;"/%&3/*< Network Profiles Network Profiles enables the user to specify a protocol and a service prefix for TANDBERG MPS dialling. Name Enter the name of the new Network Profile in the Name field. Call Prefix Enter the Call Prefix of the new Network Profile.
Page 133 The Conference Templates are found in the MCU Configuration tab. The predefined settings will be used as default settings when creating new conferences based on this specific template. TANDBERG MPS enables the setup of 10 different conference templates. The conference template contains the same settings as de- scribed in the Overview >...
Page 134 The Conference Templates are found in the MCU Configuration tab. The predefined settings will be used as default settings when creating new conferences based on this specific template. TANDBERG MPS enables the setup of 10 different conference templates. The conference template contains the same settings as de- scribed in the Overview >...
Page 135 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration 345'()*+ ',-./$0)* Appendices Contact us MCU Conference Template, cont... Conference Layouts Voice Switched 2 Split 3 Split 4 Split 2 Split Top-Bottom...
Page 136 The Conference Templates are found in the MCU Configuration tab. The predefined settings will be used as default settings when creating new conferences based on this specific template. TANDBERG MPS enables the setup of 10 different conference templates. The conference template contains the same settings as de- scribed in the Overview >...
Page 137 The Conference Templates are found in the MCU Configuration tab. The predefined settings will be used as default settings when creating new conferences based on this specific template. TANDBERG MPS enables the setup of 10 different conference templates. The conference template contains the same settings as de- scribed in the Overview >...
Page 138 The Conference Templates are found in the MCU Configuration tab. The predefined settings will be used as default settings when creating new conferences based on this specific template. TANDBERG MPS enables the setup of 10 different conference templates. The conference template contains the same settings as de- scribed in the Overview >...
Page 139 The Conference Templates are found in the MCU Configuration tab. The predefined settings will be used as default settings when creating new conferences based on this specific template. TANDBERG MPS enables the setup of 10 different conference templates. The conference template contains the same settings as de- scribed in the Overview >...
Page 140 The Conference Templates are found in the MCU Configuration tab. The predefined settings will be used as default settings when creating new conferences based on this specific template. TANDBERG MPS enables the setup of 10 different conference templates. The conference template contains the same settings as de- scribed in the Overview >...
Page 141 The Conference Templates are found in the MCU Configuration tab. The predefined settings will be used as default settings when creating new conferences based on this specific template. TANDBERG MPS enables the setup of 10 different conference templates. The conference template contains the same settings as de- scribed in the Overview >...
Page 142 Overview > MCU > Create Conference section. Encryption When set to On all participants in the conference must support DES or AES encryption (available on all TANDBERG endpoints using software version B4.0 or later). Participants not supporting encryption will be shown the ‘Encryption Required’...
Page 143 Advanced Video Option ports for this conference. Values: 0 - 40 for MPS 200 and 0 - 160 for MPS 800. Telephone Participant Limit Defines the maximum number of Telephone Participants allowed in the conference.
Page 144 The predefined settings will be used as default settings when creating encoder in the MCU to make it refresh the picture. This can be observed as a short flash in the picture. new conferences based on this specific template. TANDBERG MPS enables the setup of 10 different conference templates.
Page 145 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration 345'()*+ ',-./$0)* Appendices Contact us I:Y&:#*;2<1!'(#* File Management File Management The File Management allows viewing and changing pictures, sounds and symbols, which are shown to the participants when connecting to, and during a conference on the MCU.
Page 146 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration 345'()*+ ',-./$0)* Appendices Contact us I:Y&:#*;2<1!'(#*R cont... File Management File Management The File Management allows viewing and changing pictures, sounds and symbols, which are shown to the participants when connecting to, and during a conference on the MCU.
Page 147 MPS 200–Inserting network interface cards You will also find the technical specification About the Quality of Service (QoS) feature on the MPS 800 and MPS 200 along with About video features other information you may need to better un- About other features derstand how to utilize the TANDBERG MPS.
Page 148 Enet1 Interface Cards. The 2 x LAN interfaces will also give the TANDBERG MPS support for two Gate- The Enet2 interface is only in use if (not in use) keepers, one on each network.
Page 149 (LEDs) for power status. The backplane TANDBERG MPS 800 has support for up to 8 Media Processing Boards. of the chassis is provided with advanced TANDBERG MPS 200 has support for up to 2 Media Processing Boards. CompactPCI technology for high speed Advanced Video Option communication between the boards.
Page 150 The E1/T1 Card is equipped with rack-mountable chassis that can host up to PRI ports for ISDN interface: !" The MPS 200 supports up to 2 E1/T1 Network Interface Cards. 8 Media Processing Boards and 4 Network !" 8 x E1/T1 PRI ports (RJ-45) !"...
Page 151 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us E1/T1 Network Interface Card (IIC-8), cont... LED’s for the E1/T1 PRI Interface Card (IIC-8) Channel Service Unit (CSU)
Page 152 PRI number (which normally should be the MCUs main number). !" The TANDBERG MPS supports simultaneous dial in to the same confer- ence on ISDN. * “0” will still send NSF in the Q931 setup, which may cause calls to fail. Set to mode “off” if not needed.
Page 153 A Media Processing Board must be in front of each V.35 Serial Interface Cards. !" Interface Card. See the TANDBERG MPS 800 V.35 interface Green Power/Restart - The LEDs indicates the power sta- cards on how the V.35 Interface Cards are installed in the rear tus.
Page 154 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us V.35 Serial Interface Card (SIC-32), cont... Cable Description V.35 Pinout Table Plug A V.35 Pinout Table Plug B...
Page 155 They are installed at the back of the chassis. 8 Media Processing Boards and 4 Network If the MPS has more than 3 Media Processing Boards the TANDBERG Interface Cards. MPS is shipped with 3 hot-swappable power units.
Page 156 Appendices Contact us MPS 800–Inserting additional network interface cards TANDBERG MPS 800 The TANDBERG MPS 800 has a 9U-19” rack- mountable chassis. !" There is support for up to 4 Network Interface Cards in the software version J3 and above.
Page 157 Appendices Appendices Contact us MPS 200–Inserting additional network interface cards TANDBERG MPS 200 The TANDBERG MPS 200 has 3U-19” rack-mount- able chassis. PRI E1/T1 ISDN Interface Card !" There is support for up to 2 Network Interface 2 x PRI E1/T1 ISDN Network Interface Cards in the software version J3 and above.
Page 158 Differential Services (DiffServ) type of connection that should be chosen for the Differential services is another method of QoS offered by TANDBERG IP traffic. Helps a router select a routing path that utilizes 6 bits of the Type of Services Byte. Differential services is when multiple paths are available.
Page 159 Automatic Continuous Presence Layout Switching (CP) layout switching !" The TANDBERG MPS will transmit the same format as the one received if all the sites No of video sites in conference Picture Mode used !" are capable of receiving it.
Page 160 If H.239 or BFCP is not supported by a H.320 compression in both CIF and SIF resolutions. to be seen at the same time, in much the same site, the TANDBERG MPS uses High Speed Data H.263+ Custom Video Formats (Digital !"...
Page 161 Thus, by incorporating smart video TANDBERG has implemented asymmetrical en- nation at the same time. Lip sync problems are TANDBERG MPS can handle any value of latency algorithms, the codec sends no more video data coders and decoders.
Page 162 Inband Changing of Video and Audio Algorithms Transcoding and Ratematching Intelligent Packet Loss Recovery (IPLR TANDBERG MPS is able to change its video and audio algorithms Audio: IPLR is an ITU standard based packet loss compensation for ‘on the fly’ during a conference. This is valuable when switching H.323 that improves received video into the TANDBERG MPS.
Page 163 MPSs one will achieve a distributed setup. !" Conference Layout disabled on Slave MCU In this case the TANDBERG MPS dialling out will be defined as !" Assign Floor from Master MCU the master MCU and all other MCUs as slaves.
Page 164 TANDBERG MPS has been restarted in the meantime. Packet loss: Packet loss is displayed in the conference overview of the TANDBERG MPS, see MCU Conference Overview. The number shown is the average of audio- and video- packets that are lost dur- ing the last 2 seconds.
Page 165 Encryption Mode 2. Exchange of keys according to the common secret key and the !" If Encryption Mode is set to Auto, the TANDBERG MPS accepts selected encryption algorithm. both AES and DES encryption. 3. Start the encryption.
Page 166 Both ends of the one go, instead of manually setting each entry MS Internet Explorer 5.0 or later), the user The TANDBERG MPS can be managed in many client/server connection are authenticated via the web interface. may perform all forms of meeting set-up and...
Page 167 Both ends of the client/server Information about the intruder’s IP-address and web-interface or with API commands): and the TANDBERG MPS (the MCU web server) connection are authenticated using a digital the service used (Web, Telnet and FTP) will be !"...
Page 168 Media Processing System DESCRIPTION: Media Processing System The test reports and certificates issued by the approval agen- cies show that the TANDBERG MPS complies with the following This product complies with Commission Directives: This product complies with Commission Directives: standards.
Page 169 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us SIP - Current RFC’s and Drafts Supported !" The following current RFC’s and drafts are supported: RFC 4568 SDP:Security Descriptions for Media Streams !"...
Page 170 Server (LCS) to work properly with the MPS. SIP (Session Initiated Protocol) Software version J3 and above for the TANDBERG MPS has support for the Session Initiated Protocol (SIP). The first version of support will be compatible with the Microsoft Live Communications Server (LCS) 2005, SP1.
Page 171 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us :#*;2<1(*2&Q:5&!*D&I95&0#1&589 R cont... Configuring Microsoft Office Live Communications Server (LCS) 2005, SP1 This section will illustrate how to setup the Live Communi- cation Server (LCS) to work properly with the MPS.
Page 172 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us :#*;2<1(*2&Q:5&!*D&I95&0#1&589 R cont... Configuring Microsoft Office Live Communications Server (LCS) 2005, SP1 This section will illustrate how to setup the Live Communi- cation Server (LCS) to work properly with the MPS.
Page 173 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us :#*;2<1(*2&Q:5&!*D&I95&0#1&589 R cont... SIP Configuring on the MPS This section will illustrate how to setup the MPS for SIP. The Microsoft Live Communication Server (LCS) should be configured prior to the MPS unit.
Page 174 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us :#*;2<1(*2&Q:5&!*D&I95&0#1&589 R cont... DNS Server Configuration on the MPS The LCS SIP operation requires the MPS to have a valid DNS (Domain Name System) server configured.
Page 175 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us :#*;2<1(*2&Q:5&!*D&I95&0#1&589 R cont... Verify the Configuration Once the MPS has restarted, the Overview page of the MPS should show...
Page 176 This section will illustrate how to setup the Office Com- munication Server (OCS) to work properly with the MPS SIP (Session Initiated Protocol) Software version J3 and above for the TANDBERG MPS has support for the Session Initiated Protocol (SIP). Todays version of support is compatible with the Micro- soft Office Communications Server (OCS) 2007.
Page 177 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us :#*;2<1(*2&Z:5&!*D&I95&0#1&589 R cont... Configuring Microsoft Office Communications Server (OCS) 2007 This section will illustrate how to setup the Office Com-...
Page 178 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us :#*;2<1(*2&Z:5&!*D&I95&0#1&589 R cont... Configuring Microsoft Office Communications Server (OCS) 2007 This section will illustrate how to setup the Office Com-...
Page 179 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us :#*;2<1(*2&Z:5&!*D&I95&0#1&589 R cont... Configuring the MPS The Microsoft Office Communication Server (OCS) should be config- ured prior to the MPS unit.
Page 180 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us :#*;2<1(*2&Z:5&!*D&I95&0#1&589 R cont... DNS Server Configuration The OCS SIP operation requires the MPS to have a valid DNS (Domain Name System) server configured.
Page 181 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Appendices Contact us :#*;2<1(*2&Z:5&!*D&I95&0#1&589 R cont... Verify the Configuration Once the MPS has restarted, the Overview page of the MPS should show...
Page 182 Advanced scheduling (Multiple MCUs) with TMS Self-view optional 6?S8B=?X@"@>88BCX6S ISDN (H.320) video endpoints up to 2 Mbps Scheduling using the TANDBERG Scheduler, Microsoft Lecture mode @65>C=X["A62X>C6@ Outlook® or IBM Lotus Notes® Embedded site naming with Unicode support V.35 (H.320) video endpoints up to 2 Mbps Network authentication (H.235)
Page 183 H.221, H.231, H.241, H.242, H.243, H.245, H.320, TANDBERG and Expressway are registered trademarks or trademarks of TANDBERG in the U.S. and other H.239, H.323, BONDING (ISO 13871), Q.931, SIP, H261, H263+, H264, G711, G.722, G.722.1, G728, countries.
Page 184 Bandwidths from 56 kbps–2 Mbps in the same confer- :5>"5B?A6C6?56"@5#6S>;=?E Advanced scheduling (Multiple MCUs) with TMS Self-view optional ence Scheduling using the TANDBERG Scheduler, Microsoft Lecture mode 6?S8B=?X@"@>88BCX6S Outlook® or IBM Lotus Notes® Embedded site naming with Unicode support ISDN (H.320) video endpoints up to 2 Mbps @65>C=X["A62X>C6@...
Page 185 TANDBERG and Expressway are registered trademarks H.221, H.231, H.241, H.242, H.243, H.245, H.320, H.239, H.323, BONDING (ISO 13871), Q.931, SIP, or trademarks of TANDBERG in the U.S. and other H261, H263+, H264, G711, G.722, G.722.1, G728, countries. MPEG4 AAC-LD All other trademarks are property of their respective owners.
Page 186 MPS 200/800 Administrator Guide Contents Introduction Getting started Using the MPS System status System configuration Gateway configuration MCU configuration Appendices Contact us Contact us EUROPEAN HEADQUARTERS Philip Pedersens vei 20, 1366 Lysaker, Norway Telephone: +47 67 125 125 Fax: +47 67 125 234 Video: +47 67 126 126 E-mail: tandberg@tandberg.com...

This manual is also suitable for:

Mps 800

TANDBERG MPS 200 Administrator's Manual

Quick Links

Related Manuals for TANDBERG MPS 200

Summary of Contents for TANDBERG MPS 200

This manual is also suitable for: