Advertisement

Quick Links

EK-Pro
CPU Water Block LGA 1700
LGA 1700 NI + POM-C
| LGA 1700 AL + POM-C
USER GUIDE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Pro LGA 1700 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for EK Pro LGA 1700

  • Page 1 EK-Pro CPU Water Block LGA 1700 LGA 1700 NI + POM-C | LGA 1700 AL + POM-C USER GUIDE...
  • Page 2 This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products nor their installation.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS GENERAL INFORMATION ON WATER BLOCK COMPATIBILITY BOX CONTENTS TECHNICAL SPECIFICATIONS AND PRODUCT PARTS INSTALLING THE WATER BLOCK CLEANING THE CPU THERMAL COMPOUND APLICATION INSTALLING THE WATER BLOCK ASSEMBLY INSTALLING THE FITTINGS TESTING THE LOOP SUPPORT AND SERVICE SOCIAL MEDIA - 3 -...
  • Page 4: General Information On Water Block Compatibility

    CPU sockets: - Intel® Socket LGA 1700 BOX CONTENTS Mounting Mechanism IDENT: 106878 Thermal Grizzly Hydronaut (1g) Allen Key 2.5 mm (1 pc) EK-Pro CPU Water Block LGA 1700 EK-Pro CPU WB LGA 1700 - backplate - 4 -...
  • Page 5: Technical Specifications And Product Parts

    TECHNICAL SPECIFICATIONS AND PRODUCT PARTS The following items are enclosed with each EK-Pro LGA 1700 water block, depending on the version: EK-Pro LGA 1700 CPU water block 3831109903919 Ni + POM-C: Position Description Quantity 106336 EK MOUNTING PLATE 106343 TOP ACETAL...
  • Page 6: Installing The Water Block

    INSTALLING THE WATER BLOCK STEP 1 CLEANING THE CPU Non-abrasive Wipe the CPU’s contact surface (by using non–abrasive cloth or Cloth Q-tip). STEP 2 STEP 2 THERMAL COMPOUND APLICATION Applying thermal compound: on a clean IHS, apply a line of thermal compound and spread it over the whole CPU heat spreader (IHS) with a credit card or equivalent.
  • Page 7: Installing The Water Block Assembly

    STEP 3 INSTALLING THE WATER BLOCK ASSEMBLY Before proceeding with the installation, it is mandatory to remove the protective foil from the backside of the water block. The CPU should be attached to the processor carrier before you start this step. The carrier typically comes with the server system or motherboard.
  • Page 8: Installing The Fittings

    INSTALLING THE FITTINGS Carefully identify the direction of the flow in your circuit. For the non- rack version, EK recommends the use of EK-HFB 10 mm barb fittings and EK-Tube ZMT 10/16 mm Matte Black tubing. With EK-Pro CPU non-rack water blocks, it is mandatory to use the port in the center of the water block as the inlet port.
  • Page 9: Testing The Loop

    TESTING THE LOOP To ensure the installation of EK components was successful, we recommend you perform a 24-hour leak test. When your loop is complete and filled with coolant, connect the pump to a PSU outside your system. Do not connect power to any of the other components.
  • Page 10: Support And Service

    SPECIFICATIONS AND PRODUCT PARTS” where you can find the EAN number of each part you might need. Include the EAN number with quantity in your request. Mounting Mechanism EAN can be found under “BOX CONTENTS”. Thermal pads are readily available in the EK shop. SOCIAL MEDIA EKWaterBlocks @EKWaterBlocks...

This manual is also suitable for:

Pro lga 1700 ni + pom-cPro lga 1700 al + pom-c

Table of Contents