Related Manuals for FabiaTech Low Power FB2413
Summary of Contents for FabiaTech Low Power FB2413
- Page 1 FabiaTech Corporation IPC Solution Website: http://www.fabiatech.com Email: support@fabiatech.com PC104 CPU Board Low Power Series FB2413 User’s Manual FEB 2019 Version: 1.0 Part Number: FB2413...
- Page 2 FabiaTech shall not be reliable for technical or editorial errors or omissions, which may occur in this document. FabiaTech shall not be reliable for any indirect, special, incidental or consequential damages resulting from the furnishing, performance, or use of this document.
-
Page 3: Table Of Contents
Table of Contents FB2413 User’s Manual ......................i Chapter 1 Introducing the FB2413 System................1 Overview..........................1 Layout............................2 Specifications..........................4 Packing List ..........................5 Chapter 2 Hardware Installation ....................6 Before Installation ........................6 Hardware Features.........................7 J7: Power Connector (4-pin 2.5mm JST)............8 J6: Reset Header ....................8 ... - Page 4 Chipset Setup ....................26 IDE Configuration....................32 Serial Port Configuration ..................35 USB Configuration .....................37 Power Manager Configuration ..............39 PCIPnP Setup.........................40 Boot Setup ..........................42 Boot Setting Configuration ................43 Boot Device .......................46 Boot USB Device....................47 Boot Network Drivers ..................47 ...
-
Page 6: Chapter 1 Introducing The Fb2413 System
FabiaTech Corporation Chapter 1 Introducing the FB2413 System Overview The FB2413 is a Vortex86DX3 Low power processor, all in one PC/104 CPU board. This user’s manual provides information on the physical features, installation, and BIOS setup. Built to unleash the total potential of the Vortex86DX3 Processor, the FB2413 is a single board computer capable of handling today’s demanding requirements. -
Page 7: Layout
FabiaTech Corporation Layout LED1 CN10 CN11 BUS1... - Page 8 FabiaTech Corporation...
-
Page 9: Specifications
FabiaTech Corporation Specifications Vortex86DX3 (1GHz/L1:64K, L2:512K cache) Low Power CPU. Onboard 512MB DDR3 RAM. (1GB maximum) One Realtek 8111H 10M/100/1000 Base-TX Ethernet port. Build-in VGA Controller support VGA port. Three RS-232 ports and 1 RS232/RS422/RS485 port. Four USB (V2.0) ports and one SATA interface Compact Flash socket for 3.3V Compact Flash and Micro Drives. -
Page 10: Packing List
FabiaTech Corporation Packing List Upon receiving the package, verify the following things. If any of the mentioned happens, contact us for immediate service. • Unpack and inspect the FB2413 package for possible damage that may occur during the delivery process. -
Page 11: Chapter 2 Hardware Installation
FabiaTech Corporation Chapter 2 Hardware Installation This chapter introduces the system connectors & jumper settings, and guides you to apply them for field application. Before Installation Before you install the system, make sure you follow the below descriptions. 1. Before removing the board from its anti-static bag, wear an anti-static strap to prevent the generation of Electricity Static Discharge (ESD). -
Page 12: Hardware Features
FabiaTech Corporation Hardware Features The following list is for the setup of the connectors and jumpers of the FB2413. Item Description 12-pin header for FB4760 RJ45-Lan adapter CN4, CN3, CN2 10-pin 2.0mm RS-232 Serial 2, 3, 4 port connector (JST) 10-pin 2.0mm RS-232/RS422/RS485 Serial 1 port connector (JST) -
Page 13: J7: Power Connector (4-Pin 2.5Mm Jst)
FabiaTech Corporation J7: Power Connector (4-pin 2.5mm JST) LED1 Signal VCC (+5V) CN10 Ground Ground VDD (+12V) CN11 Note: FB2413 needs +5V only, +12V is not necessary. BUS1 Note: Be careful with the pin orientation when installing power connector. A wrong connection can easily destroy your FB2413 board. -
Page 14: Cn1: Rj45 Lan /Adapter Connector With Led Indicators
FabiaTech Corporation CN1: RJ45 LAN /Adapter Connector with LED indicators FB4760 is a RJ45 connector with 2 LEDs for LAN. The left side LED (orange) indicates data which is being accessed and the right side LED (green) indicates on-line status. -
Page 15: Cn7: Keyboard/Mouse Connector
FabiaTech Corporation CN7: Keyboard/Mouse Connector CN7 is a 6-pin 2.0mm JST connector, use the included KB/MS adapter cables you can attach standard PS/2 type keyboard and mouse. LED1 CN10 Signal Mouse Data CN11 Keyboard Data Ground Mouse Clock Keyboard Clock... -
Page 16: J3 & J5: Usb Connector
FabiaTech Corporation J3 & J5: USB Connector Use the USB adapter cable, you can attach up to 4 USB devices. J3 & J5 LED1 Description Description CN10 USBV0 Case Ground USBD0- USBG1 USBD0+ USBD1+ CN11 USBG0 USBD1- Case Ground USBV1 BUS1 LED1 &... -
Page 17: Cn5, Cn4, Cn3 & Cn2: Serial Port Connectors
FabiaTech Corporation CN5, CN4, CN3 & CN2: Serial Port Connectors CN5 (Serial Port1), CN4 (Serial Port2), CN3 (Serial Port3) & CN2 (Serial Port4) are 10-pin 2.0mm IDC connectors. The included serial port adapter cables are used to transfer 10-pin 2.0mm JST into standard DB-9 connector. The following tables show the signal connections of these connectors and the included adapter cable for CN2 to CN5. -
Page 18: Cf1: Compact Flash Socket
FabiaTech Corporation CF1: Compact Flash Socket The Compact Flash socket CF1 (on the solder side) and supports 3.3V Compact Flash and Micro Drives. J CN9: Serial ATA hard Disk Connector This CN9 connector is for SATA hard disk Use the SATA cables to SATA hard disk drives. -
Page 19: Cn6 & Jp1: Battery And Clear Cmos Data
FabiaTech Corporation CN6 & JP1: Battery and Clear CMOS Data The CN6 is used to connect an external battery pack if Lithium battery is empty; please replace the battery with a new one. You can use JP1 to clear CMOS data. -
Page 20: Bus1: Pc/104 Bus Connectors
FabiaTech Corporation BUS1: PC/104 Bus Connectors LED1 BUS1 – BUS A & B CN10 BUS1 – BUS C & D CN11 BUS1 PC/104 A & B Pin Signal Signal Signal Signal -IOCHK SA14 Ground -DACK1 SA13 RSTDRV DRQ1 SA12 -Refresh... - Page 21 FabiaTech Corporation...
-
Page 22: Chapter 3 Installing Vga & Lcd Display
FabiaTech Corporation Chapter 3 Installing VGA & LCD Display y LVDS LCD FLAT PANEL DISPLAY LVDS LCD FLAT PANEL DISPLAY Using the BIOS setting for different types of LVDS LCD module, then set your system Using the BIOS setting for different types of LVDS LCD module, then set your system... -
Page 23: Cn8: Analogy Vga Display Connector
FabiaTech Corporation CN8: Analogy VGA Display Connector The FB2413 supports a VGA colored monitor and a LVDS LCD. It can be connected to create a compact video solution for the industrial environment. The following table and figure illustrate the pin definition of CN8 and D-sub 15-pin on... -
Page 24: Cn10 & Cn11: Lvds Lcd Connector And Power Connector (Optional)
Ground LVDS_CK+ LVDS_CK- Ground LDP0_AUX+ 15 LTDP0_AUX- Ground Ground Ground Ground Ground 27 LVDS_+3.3V 28 LVDS_+3.3V 29 LVDS_+3.3V 30 LVDS_+3.3V NOTE: If any trouble occurs when connecting FB2413 with LCD panels, you could contact technical support division of FabiaTech Corporation. - Page 25 FabiaTech Corporation...
-
Page 26: Chapter 4 Bios Setup
FabiaTech Corporation Chapter 4 BIOS Setup This chapter describes the BIOS setup. Overview BIOS are a program located on a Flash memory chip on a circuit board. It is used to initialize and set up the I/O peripherals and interface cards of the system, which includes time, date, hard disk drive, the ISA bus and connected devices such as the video display, diskette drive, and the keyboard. -
Page 27: Bios Functions
FabiaTech Corporation BIOS Functions On the menu, you can perform the following functions 1. Main 2. Advanced CHIPSET Configuration IDE Configuration Serial Port Configuration USB Configuration Power Management Configuration Shadow RAM Configuration Patcher ROM Setting 3. PCIPnP 4. Boot Boot Settings Configuration... -
Page 28: Keyboard Convention
FabiaTech Corporation Save Changes and Exit: Exit system setup after saving the changes.F10 key can be used for this operation. Discard Changes and Exit: Exit system setup without saving any changes. ESC key can be used for this operation. Discard Changes: Discard changes down so far any of the set questions. -
Page 29: Main Setup
FabiaTech Corporation Main Setup This section describes basic system hardware configuration, system clock setup and BIOS version information. If the CPU board is already installed in a working system, you will not need to select this option anymore. System Memory... -
Page 30: Advanced Setup
FabiaTech Corporation Advanced Setup Select the Advanced tab from the setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as IDE Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the <Arrow>... -
Page 31: Chipset Setup
FabiaTech Corporation Chipset Setup This section describes the configuration of the board’s chipset features. • NorthBridge Configuration • SouthBridge Configuration... - Page 32 FabiaTech Corporation Northbridge Configuration CPU Configuration You can use this screen to select options for the CPU information. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option.
- Page 33 FabiaTech Corporation VGA Configuration (LCD Panel Function is Optional) This field item is for FB2413x, when using the LCD the field specifies the selections of display for different TFT LCD display type. LCD Panel Index When use the LCD the field specifies which select display resolution for different TFT LCD display type.
- Page 34 FabiaTech Corporation Southbridge Configuration You can use this screen to select options for the South Bridge Configuration. South Bridge is a chipset on the motherboard that controls the ISA functions, and Watch Dog function. ISA Configuration...
- Page 35 FabiaTech Corporation ISA Clock This field sets the polling clock speed of ISA Bus (PC/104). Available Options: 8.3MHz and 16.6 MHz Default setting: 8.3MHz NOTE:1. PCICLK means the PCI BUS inputs clock (33Mhz). 2. User is recommended to use setting at 8.3MHz.
- Page 36 FabiaTech Corporation Watchdog Configuration Watchdog 1 Function This field specifies the Enabled or Disabled of the Watchdog Function. Available Options: Disabled and Enabled Default setting: Disabled Watchdog 1 Signal Select This field is the Select IRQ, NMI or Reset signal trigger of onboard watchdog.
-
Page 37: Ide Configuration
FabiaTech Corporation IDE Configuration You can use this screen to select options for the IDE Configuration Settings. Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change the value of the selected option. A description of the selected item appears on the right side of the screen. - Page 38 FabiaTech Corporation reconfigure your hard drive type. If you use older hard disk drives, which do not support this feature, then you must configure the hard disk drive in the standard method as described above by the <USER> option. PIO MODE PIO means Programmed Input/Output.
- Page 39 FabiaTech Corporation OnBoard IDE Operate Mode This item specifies the Native Mode ONLY for Windows(R) XP and 2000. Available Options: Legacy, and Native mode Default setting: Native mode Not Program PIO Mode If the bios cannot detect the CF or IDE, this will allow you to indicate the CF or IDE card to Primary Channel or Secondary Channel.
-
Page 40: Serial Port Configuration
FabiaTech Corporation Serial Port Configuration This section describes the function of Super I/O settings. SB Serial Port 1 These fields select the I/O port address for each Serial port. Available Options: Disabled, 3F8H, 2F8H, 3E8H, 2E8H, 360, 260, 368, 268, 3E0, and 2E0H. - Page 41 FabiaTech Corporation SB Serial Port 2 These fields select the I/O port address for each Serial port. Available Options: Disabled, 3F8H, 2F8H, 3E8H, 2E8H, 360, 260, 368, 268, 3E0, and 2E0H. Default setting: 2F8 Serial Port 2 IRQ This field is the Serial port 2 Interrupt.
-
Page 42: Usb Configuration
FabiaTech Corporation USB Configuration You can use this screen to select options for the USB Configuration. USB Support Select Enable, if a USB device is installed to the system. If Disabled are selected, the system will not be able to use a USB device. - Page 43 FabiaTech Corporation USB 2.0 Controller Mode This field is configures the USB 2.0 controllers in High speed (480Mbps) or Full speed (12Mbps). Available Options: HiSpeed and FullSpeed Default setting: Hispeed BIOS ECHI Hand-Off This is a workaround for OS without ECHI Hand-Off support. The ECHI ownership change should claim by ECHI driver.
-
Page 44: Power Manager Configuration
FabiaTech Corporation Power Manager Configuration APM Configuration APM Support Select Enabled to activate the chipset Power Management and APM (Advanced Power Management) features. Available Options: Disable, and Enable Default setting: Disable ACPI Configuration ACPI Aware OS Enable or Disabled ACPI support OS... -
Page 45: Pcipnp Setup
FabiaTech Corporation PCIPnP Setup Select the PCI/PnP tab from the setup screen to enter the Plug and Play BIOS Setup screen. You can display a Plug and Play BIOS Setup option by highlighting it using the <Arrow> keys. All Plug and Play BIOS Setup options are described in this section. The Plug and Play BIOS Setup screen is shown below. - Page 46 FabiaTech Corporation PCI Latency Timer This field specifies the latency timings (in PCI clock) PCI devices installed in the PCI expansion bus. Available Options: 32, 64, 96, 128, 160,192, 224, and 248 Default setting: 64 PCI IDE BusMaster This option is to specify that the IDE controller on the PCI local bus have bus- mastering capability.
-
Page 47: Boot Setup
FabiaTech Corporation Boot Setup Select the Boot tab from the setup screen to enter the Boot BIOS Setup screen. You can select any of the items in the left frame of the screen, such as Boot Device Priority, to go to the sub menu for that item. You can display a Boot BIOS Setup option by highlighting it using the <Arrow>... -
Page 48: Boot Setting Configuration
FabiaTech Corporation Boot Setting Configuration Quick Boot This field is used to activate the quick boot function of the system. When set to Enabled, 1. BIOS will not wait for up to 40 seconds if a Ready signal is not received from the IDE drive, and will not configure its drive. - Page 49 FabiaTech Corporation AddOn ROM Display Mode Set this option to display add-on ROM (read-only memory) messages. An example of this is a SCSI BIOS or VGA BIOS. 1. Force BIOS Set this value to allow the computer system to force a third party BIOS to display during system boot.
- Page 50 FabiaTech Corporation It will prevent the message from appearing on the first BIOS screen when the computer boots. Available options: Disabled, Enabled Default setting: Enabled Interrupt 19 Capture Set this value to allow option ROMs such as network controllers to trap BIOS interrupt 19.
-
Page 51: Boot Device
FabiaTech Corporation Boot From LAN This field specifies the PXE boot ROM of the onboard LAN chip. Available Options: Disabled, Enable Default setting: Disable Boot Device Use this screen to specify the order in which the system checks for the device to boot from. -
Page 52: Boot Usb Device
FabiaTech Corporation Boot USB Device Use this screen to view the USB Device drives in the system. To access this screen, select USB Device drives on the Boot Setup screen and press <Enter>. Boot Network Drivers Use this screen to view the Network drives in the system. To access this screen,... -
Page 53: Security Setup
FabiaTech Corporation Security setup There are two security passwords: Supervisor and User. Supervisor is a privileged person that can change the User password from the BIOS. According to the default setting, both access passwords are not set up and are only valid after you set the password from the BIOS. - Page 54 FabiaTech Corporation Always: a visitor who attempts to enter BIOS or operating system will be prompted for password. Setup: a visitor who attempts to the operating system will be prompted for user password. You can enter either User password or Supervisor password.
- Page 55 FabiaTech Corporation RDC Engineer Mode Pressing function key ALT+F4 when in the Security menu reveals RDC Engineering Mode, which must be enabled before the Chipset submenu on the Advanced menu tab becomes visible and accessible. Available Options: Disabled, Enable Default setting: Disable...
- Page 56 FabiaTech Corporation I/O Interface Security USB Control 1/2 Interface If Disabled are selected, the system USB Control will not be able to use a USB device. Available Options: Disabled, Enabled Default setting: Enabled COM1/2 Port Interface If Disabled are selected, the system I/O Control will not be able to use a COM device.
- Page 57 FabiaTech Corporation...
-
Page 58: Chapter 5 Driver And Utility
FabiaTech Corporation Chapter 5 Driver and Utility The enclosed diskette includes FB2413 VGA and LAN driver. To install and configure you FB2413 system, you need to perform the following steps. VGA Drivers WINDOWS Driver To install the VGA driver, insert the CD ROM into the CD ROM device, and enter DRIVER>VGA>Vortex86DX3. -
Page 59: Lan Utility & Driver
FabiaTech Corporation LAN Driver To install the LAN driver, insert the CD ROM into the CD ROM device, and enter DRIVER>LAN>RTL8111H>WINXP. If your system is not equipped with a CD ROM device, copy the LAN driver from the CD ROM to a CF. -
Page 60: Watchdog Timer
FabiaTech Corporation Watchdog Timer This section describes how to use the Watchdog Timer 0 and Watchdog Timer 1, including disabled, enabled, and triggers functions. The FB2413 is equipped with a programmable time-out period watchdog timer. User can use the program to enable the watchdog timer. Once you have enabled the watchdog timer, the program should trigger it every time before it times out. - Page 61 FabiaTech Corporation Watchdog timer – WDT0 and WDT1 WDT 0 WDT 1 D7…D0 D7…D0 D7…D0 Counter [MSB …LSB] For example: WDT 0 WDT 1 30.5 μsec 61.0μsec 7.8 m sec 15.6 m sec 2 sec 4 sec 512 sec Select Watchdog Report Signal - WDT0 and WDT1...
-
Page 62: Setup Watchdog Timer Step - Wdt0 And Wdt1
FabiaTech Corporation NOTE: If you program the watchdog to generate IRQ15 signal when it times out, you should initial IRQ15 interrupt vector and enable the second interrupt controller (8259 PIC) in order to enable CPU to process this interrupt. An interrupt service routine is required too. - Page 63 FabiaTech Corporation Watchdog Timer Enabled To enable the watchdog timer 0 (WDT 0), you have to output a byte of timer factor to the watchdog register whose index address is 22h and data port is 23H. The following is an Assemble program, which demonstrates how to enable the watchdog timer and set the time-out period at 4 seconds.
- Page 64 FabiaTech Corporation Watchdog Timer Trigger After you enable the watchdog timer, your program must write the same factor as enabling to the watchdog register at least once every time-out period to its previous setting. You can change the time-out period by writing another timer factor to the watchdog register at any time, and you must trigger the watchdog before the new time-out period in next trigger.
- Page 65 FabiaTech Corporation WDT1 setup Step: 1. Write time into register AAh-ACh. 2. Select signal from register A9h. 3. Set register A8h bit 8 to enable WDT1. To clear the watchdog timer counter: 1. Write any value to register A7H Watchdog Timer Enabled To enable the watchdog timer 1 (WDT 1), you have to output a byte of timer factor to the watchdog ports address is A8h.
-
Page 66: Chapter 6 Technical Reference
FabiaTech Corporation Chapter 6 Technical Reference This section outlines the errors that may occur when you operate the system, and also gives you the suggestions on solving the problems. Topic include: Trouble Shooting for Post Beep & Error Messages Technical Reference Trouble Shooting for Post Beep and Error Messages The following information informs the Post Beep &... - Page 67 FabiaTech Corporation CMOS CHECKSUM ERROR This error informs that the CMOS has corrupted. When the battery runs weak, this situation might happen. Please check the battery and change a new one when necessary. DISK BOOT FAILURE When you can‘t find the boot device, insert a system disk into Drive A and press <...
- Page 68 FabiaTech Corporation MEMORY SIZE HAS CHANGED Memory has been added or removed since last boot. In EISA mode, use Configuration Utility to re-configure the memory configuration. In ISA mode enter BIOS Setup and enter the new memory size in the memory fields.
-
Page 69: Technical Reference
FabiaTech Corporation Technical Reference Physical and Environmental Temperature: Operating 0°C ~ 60°C Relative humidity 5 % to 95 % non-condensing Real-Time Clock and Non-Volatile RAM The FB2413 contains a real-time clock compartment that maintains the date and time in addition to storing configuration information about the computer system. It contains 14 bytes of clock and control registers and 114 bytes of general purpose RAM. - Page 70 FabiaTech Corporation Address Description Fixed disk type byte, drive D Reserved Equipment byte Low base memory byte High base memory byte Low expansion memory byte High expansion memory byte 19-2D Reserved 2E-2F 2-byte CMOS checksum Low actual expansion memory byte...
-
Page 71: Cmos Ram Map
FabiaTech Corporation CMOS RAM Map Register Description 00h -10h Standard AT-compatible RTC and Status and Status Register data definitions 11h – 13h Varies Equipment Bits Number of Floppy Drives 1 Drive 2 Drives Bits Monitor Type Not CGA or MDA 01 40x25 CGA... -
Page 72: I/O Port Address Map
FabiaTech Corporation I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses, which also becomes the identity of the device. There is a total of 1K-port address space available. The following table lists the I/O port addresses used on the Industrial CPU Card. -
Page 73: Interrupt Request Lines (Irq)
FabiaTech Corporation Interrupt Request Lines (IRQ) There are a total of 15 IRQ lines available on the Industrial CPU Card. Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on the Industrial CPU Card. -
Page 74: Serial Ports
FabiaTech Corporation Serial Ports The ACEs (Asynchronous Communication Elements ACE1 to ACE2) are used to convert parallel data to a serial format on the transmit side and convert serial data to parallel on the receiver side. The serial format, in order of transmission and reception, is a start bit, followed by five to eight data bits, a parity bit (if programmed) and one, one and half (five-bit format only) or two stop bits. - Page 75 FabiaTech Corporation Bit 1: Enable Transmitter Holding Empty Interrupt (ETBEI) Bit 2: Enable Receiver Line Status Interrupt (ELSI) Bit 3: Enable MODEM Status Interrupt (EDSSI) Bit 4: Must be 0 Bit 5: Must be 0 Bit 6: Must be 0...
- Page 76 FabiaTech Corporation Bit 5: Stick Parity Bit 6: Set Break Bit 7: Divisor Latch Access Bit (DLAB) MODEM Control Register (MCR) Bit 0: Data Terminal Ready (DTR) Bit 1: Request to Send (RTS) Bit 2: Out 1 (OUT 1) Bit 3: Out 2 (OUT 2)
- Page 77 FabiaTech Corporation Bit 4: Clear to Send (CTS) Bit 5: Data Set Ready (DSR) Bit 6: Ring Indicator (RI) Bit 7: Received Line Signal Detect (RSLD) Divisor Latch (LS, MS) Bit 0: Bit 0 Bit 8 Bit 1: Bit 1...
-
Page 78: Appendix
FabiaTech Corporation Appendix Dimension Top Side 90.2 73.7 10.7 80.0... - Page 79 FabiaTech Corporation Solder Side...