1. Manuals
  2. Brands
  3. FabiaTech Manuals
  4. Computer Hardware
  5. Low Power FB2652
  6. User manual

FabiaTech Low Power FB2652 User Manual

Embedded cpu board
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FabiaTech Corporation
IPC Solution
Website:
http://www.fabiatech.com
Email:
support@fabiatech.com
Embedded CPU Board
Low Power Series
FB2652
User's Manual
SEP 2006
Version: 1.1
Part Number: FB2652

Advertisement

Table of Contents
loading

Related Manuals for FabiaTech Low Power FB2652

Summary of Contents for FabiaTech Low Power FB2652

  • Page 1 FabiaTech Corporation IPC Solution Website: http://www.fabiatech.com Email: support@fabiatech.com Embedded CPU Board Low Power Series FB2652 User’s Manual SEP 2006 Version: 1.1 Part Number: FB2652...
  • Page 2 FabiaTech shall not be reliable for technical or editorial errors or omissions, which may occur in this document. FabiaTech shall not be reliable for any indirect, special, incidental or consequential damages resulting from the furnishing, performance, or use of this document.

  • Page 3: Table Of Contents

    Table of Contents FB2652 User’s Manual......................i Chapter 1 Introducing the FB2652 System ................. 1 Overview ............................ 1 Series Comparison Table ......................2 Layout ............................3 Specifications ..........................4 Packing List..........................5 Chapter 2 Hardware Installation ....................7 Before Installation ........................7 Hardware Features........................
  • Page 4 BIOS Functions .....................22 　 Keyboard Convention ..................23 　 STANDARD CMOS SETUP......................24 BIOS Features Setup .......................27 Chipset Features Setup......................30 Integrated Peripherals ......................34 POWER MANAGEMENT ......................39 PnP/PCI Configurations ......................42 PC Health Status ........................44 Password Setup ........................45 Chapter 5 Software Installation....................47 System Driver..........................47 WIN 98/2000/XP Driver....................47 VGA Driver for WIN98SE/ME/2000/XP/NT4.0 ..............48 Audio Drivers..........................48...
  • Page 5 DMA Controller 2......................63 Serial Ports........................64 Parallel Ports ........................68 Appendix............................71 Dimension..........................71...

  • Page 7: Chapter 1 Introducing The Fb2652 System

    FabiaTech Corporation Chapter 1 Introducing the FB2652 System Overview The FB2652 is an embedded system with 5.1/2" low-power Pentium-M CPU module inside. This user’s manual provides information on the physical features, installation, and BIOS setup of the FB2652. Built to unleash the total potential of the Pentium-M or Celeron-M Processor, Able to support 600MHz ~ 1.4Ghz CPUs, this system supports two 10/100/1000M Base –TX...

  • Page 8: Series Comparison Table

    FabiaTech Corporation Series Comparison Table Model FB2652 FB2652A Processor Intel Celeron-M Intel Pentium-M 600MHz 1.4GHz Chipset 855GME+ICH4 1 184 Pin-DIMM (Max.) CRT VGA Watchdog Timer Multi I/O Two Serial and One Parallel Enhanced IDE USB 2.0 Four Audio Line -Out And MIC...

  • Page 9: Layout

    FabiaTech Corporation Layout DIMM1 LED1 BUS1...

  • Page 10: Specifications

    FabiaTech Corporation Specifications On-board Low Power Intel Celeron-M 600MHz or Pentium-M 1.1 GHz ~1.4GHz CPU with heat - sink only. Intel 855GME+ICH4 chipset and 512k or above L2 cache inside the CPUs. Provide one DIMM 184-pin Socket for up to 1GB DDR-333 maximum.

  • Page 11: Packing List

    FabiaTech Corporation Packing List Upon receiving the package, verify the following things. Should any of the mentioned happens, contact us for immediate service. • Unpack and inspect the FB2652 package for possible damage that may occur during the delivery process.
  • Page 12 FabiaTech Corporation...

  • Page 13: Chapter 2 Hardware Installation

    FabiaTech Corporation Chapter 2 Hardware Installation This chapter introduces the system connectors & jumper settings, and guides you to apply them for field application. Before Installation Before you install the system board, make sure you follow the following descriptions. 1. Before removing the board from its anti-static bag, wear an anti-static strap to prevent the generation of Electricity Static Discharge (ESD).

  • Page 14: Hardware Features

    FabiaTech Corporation Hardware Features The following lists the connectors and jumpers to install the FB2652. Item Description 40-pin IDE hard disk connector 30-pin LVDS LCD Connector 5-pin Power Connector for LVDS LCD inverter board ATX Power Supply Connector Keyboard and Mouse connector...

  • Page 15: J2: Cpu Fan Connector

    FabiaTech Corporation J2: CPU Fan Connector J2 is a 3-pin Molex connector and which is reserved to drive CPU cooling fan when non-low power CPU are used. DIMM1 LED1 BUS1 Description Ground +12V Speed-In J1: External Power/LAN/GPIO LED’s Indicators & Temp/Reset/PWR-SW Header The Power and HDD LED’s has two distinctive status: Off for inactive operation and...
  • Page 16 FabiaTech Corporation 1. The J1 pin 11,12 is a 2-pin for connecting Resistive Temperature Sensor input header and pin 13,14 is a 2-pin for connecting to system reset bottom. It is cause hardware reset of FB2652 and restart system booting.

  • Page 17: Cn5: Connecting The Keyboard And Mouse

    FabiaTech Corporation CN5: Connecting the Keyboard and Mouse The CN5 down side connector (Purple) can attach standard PS/2 type keyboard and up side (Green) can attached PS/2 mouse. Standard PS/2 keyboard and Mouse can be plugged into this connector without any adapter cable.

  • Page 18: Cn8 & Cn9: Connecting The L1/L2 Lan Ports And Usb Ports

    FabiaTech Corporation The CN6 printer port is standard DB25 connector. DB-25 Description DB-25 Description -STROBE -AUTO FORM FEED DATA 0 -ERROR DATA 1 -INITIALIZE DATA 2 -PRINTER SELECT IN DATA 3 Ground DATA 4 Ground DATA 5 Ground DATA 6...

  • Page 19: Cn7: Connecting The Audio Microphone In/ Speak Out

    FabiaTech Corporation CN7: Connecting the Audio Microphone In/ Speak Out DIMM1 LED1 Line-Out BUS1 Mic-In J5: TTL I/O Connector DIM M 1 LE D1 B US1 TTL Lines Bit Location CN 4 Output Line 0 C N3 Please refer to...

  • Page 20: Cn1: Ide Hard Disk Connector

    FabiaTech Corporation CN1: IDE hard Disk Connector CN1 is 40-pin 2.54mm IDC connectors. The IDE interface has one enhanced IDE channels and supports 2 IDE devices. DIMM1 LED1 CN1 – Hard disk connector BUS1 The following table lists the pin description of CN1.

  • Page 21: Bus2: Mini-Pci Socket For Wlan Modules

    FabiaTech Corporation BUS2: Mini-PCI Socket for WLAN Modules The BUS2 is Mini-PCI socket (on the solder side) is ideal for wireless LAN module or other I/O modules. Installing Memory: DIMM Socket for DDR Modules You may extend additional memory to FB2652 See as following figure and rear pictures.

  • Page 22: Cn4: Atx Power Supply Connector

    FabiaTech Corporation CN4: ATX Power Supply Connector The connector connecting ATX power supply, you can connect CN4 to ATX power supply, and connect J1 (pin15 &pin16) to a push bottom switch as soft power switch. DIMM1 LED1 BUS1 Signal Signal 3.3V...

  • Page 23: Chapter 3 Installing Crt & Lvds Lcd

    FabiaTech Corporation Chapter 3 Installing CRT & LVDS LCD This chapter describes the configuration and installation procedure of LVDS LCD’s and CRT displays. Both CRT and LVDS LCD displays may be used at the same time. However, each type of LVDS LCD requires different BIOS setting. This section describes the configuration and installation procedure using LVDS LCD display.

  • Page 24: Crt & Lvds Lcd Display

    FabiaTech Corporation CRT & LVDS LCD DISPLAY The FB2652 supports a CRT colored monitor and a LVDS LCD. It can be connected to create a compact video solution for the industrial environment. 32MB simulated VRAM allows a maximum CRT resolution of 1600X1200 with 64K colors.

  • Page 25: Cn2 & Cn3: Lvds Lcd Connector And Power Connector

    +12V Ground Ground Ground ENVDD N.C. Ground Ground YCK+ YCK- Ground Ground Ground Ground ZCK+ ZCK- Ground Ground +3.3V +3.3V Note: If any trouble when connecting FB2652 with LVDS LCD panels, you could contact technical support division of FabiaTech Corporation.
  • Page 26 FabiaTech Corporation...

  • Page 27: Chapter 4 Bios Setup

    FabiaTech Corporation Chapter 4 BIOS Setup This chapter describes the BIOS setup. Overview BIOS are a program located on a Flash memory chip on a circuit board. It is used to initialize and set up the I/O peripherals and interface cards of the system, which includes time, date, hard disk drive, the ISA bus and connected devices such as the video display, diskette drive, and the keyboard.

  • Page 28: Bios Functions

    FabiaTech Corporation BIOS Functions On the menu, you can perform the following functions 1. Standard CMOS Features 2. Advanced BIOS Features 3. Advanced Chipset Features 4. Integrated Peripherals 5. Power Management Setup 6. PNP/PCI Configuration 7. PC Health States 8. Set Supervisor Password 9.

  • Page 29: Keyboard Convention

    FabiaTech Corporation Keyboard Convention On the BIOS, the following keys can be used to operate and manage the menu: Item Function To exit the current menu or message Page Up/Page Down To select a parameter To display the help menu if you do not know the...

  • Page 30: Standard Cmos Setup

    FabiaTech Corporation STANDARD CMOS SETUP This section describes basic system hardware configuration, system clock setup and error handling. If the CPU board is already installed in a working system, you will not need to select this option anymore. Date & Time Setup Highlight the <Date>...
  • Page 31 FabiaTech Corporation You can select <AUTO> under the <TYPE> and <MODE> fields. This will enable auto detection of your IDE drives during boot up. This will allow you to change your hard drives (with the power off) and then power on without having to reconfigure your hard drive type.
  • Page 32 FabiaTech Corporation Extended Memory The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1MB in the CPU’s memory address map. Total Memory System total memory is the sum of basic memory, extended memory, and other...

  • Page 33: Bios Features Setup

    FabiaTech Corporation BIOS Features Setup This section describes the configuration entries that allow you to improve your system performance, or let you set up some system features according to your preference. Some entries here are required by the CPU board’s design to remain in their default settings.
  • Page 34 FabiaTech Corporation Quick Power On Self Test This option speeds up Power On Self Test (POST) after you power on the computer. If it is set to Enable, BIOS will shorten or skip some items’ checks during POST. Available options: Disabled, Enabled...
  • Page 35 FabiaTech Corporation Default setting: 250 Security Option This field enables password checking every time the computer is powered on or every time the BIOS Setup is executed. If Always is chosen, a user password prompt appears every time and the BIOS Setup Program executes and the computer is turned on.

  • Page 36: Chipset Features Setup

    FabiaTech Corporation Chipset Features Setup This section describes the configuration of the board’s chipset features. DRAM Timing Selectable SPD represents Serial Presence Detect. It is an 8-bit, 2048 bits EEPROM, built on the SDRAM for different frequencies. If the installed SDRAM supports SPD function, select SPD.
  • Page 37 FabiaTech Corporation DRAM RAS# to CAS# delay This field specifies the length of the delay inserted between RAS and CAS signals of the Synchronous DRAM system access cycle when SDRAM is installed. Available Options: 3, 2 Default setting: 3 DRAM RAS# Precharge This field specifies the length of the RAS pre-charge part of the Synchronous DRAM access cycle when SDRAM is installed.
  • Page 38 FabiaTech Corporation Delayed Transaction This field specifies the chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1. Available Options: Disabled, Enabled Default setting: Enabled AGP Aperture Size (MB) This field specifies the system memory size that can be used by the Accelerated Graphics Port (AGP).
  • Page 39 FabiaTech Corporation LCD Panel Type Table Panel ID Function 640x480 800x600 1024x768 1280x1024 1400x1050 1400x1050 1600x1200 1280x768 1600x1050 1920x1200 1024x768 1024x768 1024x768 1280x800 1280x600 1024x768...

  • Page 40: Integrated Peripherals

    FabiaTech Corporation Integrated Peripherals This section describes the function of peripheral features. OnChip IDE Device OnChip Primary/Secondary PCI IDE This field specifies the IDE channel that can be applied when using IDE hard disk connector. Available Options: Disabled, Enable Default setting: Enable...
  • Page 41 FabiaTech Corporation IDE Primary/Secondary Master/Slave PIO IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship, which is determined by the cabling configuration used to attach them to the controller. Your system supports one IDE controller – a primary and a secondary –...
  • Page 42 FabiaTech Corporation USB Device KB Support Select All Device if a USB device is installed to the system. If Disabled are selected, the system will not be able to use a USB device. Available Options: Disabled, Mice and All Devices Default setting: All Devices AC’97 Audio...
  • Page 43 FabiaTech Corporation SuperIO Device OnBoard FDC This field enables the floppy drive controller on the FB2642. Available Options: Disabled, Enabled and Auto Default setting: Auto OnBoard Serial Port 1 These fields select the I/O port address for each Serial port.
  • Page 44 FabiaTech Corporation OnBoard Parallel Port This field selects the I/O port address for parallel port. Available Options: Disabled, 378/IRQ7, 278/IRQ5, and 3BC/IRQ7 Default setting: 378/IRQ7 Parallel Port Mode This field specifies the parallel port mode. ECP and EPP are both bi-directional data transfer schemes that adhere to the IEEE P1284 specifications.

  • Page 45: Power Management

    FabiaTech Corporation POWER MANAGEMENT ACPI Function This filed specifies allow you enable Advanced Configuration and Power Management. When you use Windows/0S standby mode can set to enable. Available Options: Disabled, Enabled Default setting: Enable Power Management Select Enabled to activate the chipset Power Management and APM (Advanced Power Management) features.
  • Page 46 FabiaTech Corporation Select this option if your monitor supports the Display Power Management DPMS - Signal (DPMS) standard of the Video Electronics Standards to select video power management values. Available Options: V/H SYNC + Blank, Blank Screen and DPMS Default setting: DPMS Suspend Type This field defines the continuous idle time before the system enters PwrOn Suspend.
  • Page 47 FabiaTech Corporation Time (hh:mm:ss) Alarm This field specifies the hour/ minute/second of the RTC alarm. Available Options: 1-24/0-60/0-60 Default setting: 00...

  • Page 48: Pnp/Pci Configurations

    FabiaTech Corporation PnP/PCI Configurations Reset Configuration Data: Enable, Disable If you select Enable to reset Extended System Configuration Data (ESCD) when you exit setup is you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operation operating system cannot boot.
  • Page 49 FabiaTech Corporation X IRQ Resources IRQ-n Assigned: PCI Device and Reserved You may assign each system interrupt a type, depending on the type of device using the interrupt. PCI/VGA Palette Snoop When Enabled is selected, multiple VGA devices operating on different buses can handle data from the CPU on each set of palette registers on every video device.

  • Page 50: Pc Health Status

    FabiaTech Corporation PC Health Status On the Hardware Monitor Setup screen, you can monitor the system temperature, CPU voltage, and CPU fan speed… System Hardware Monitor In this field, you can monitor or detect the followings items. These items are view-only and cannot be changed.

  • Page 51: Password Setup

    FabiaTech Corporation Password Setup There are two security passwords: Supervisor and User. Supervisor is a privileged person that can change the User password from the BIOS. According to the default setting, both access passwords are not set up and are only valid after you set the password from the BIOS.
  • Page 52 FabiaTech Corporation...

  • Page 53: Chapter 5 Software Installation

    FabiaTech Corporation Chapter 5 Software Installation The enclosed diskette includes FB2652 VGA, Audio, USB, System and LAN driver. To install and configure you FB2652 system, you need to perform the following steps. System Driver WIN 98/2000/XP Driver Installs 855GME Chipset, IRQ Routing, USB, AGP Driver and PCI IDE Bus Master Driver.

  • Page 54: Vga Driver For Win98Se/Me/2000/Xp/Nt4.0

    FabiaTech Corporation VGA Driver for WIN98SE/ME/2000/XP/NT4.0 Step 1: To install the VGA driver, insert the CD ROM into the CD ROM device, and enter DRIVER>VGA>855GME>WIN2K_XP, WIN98_ME or WINNT4. Step 2: Execute SETUP.EXE file. Step 3: The screen shows the SETUP type. Press any key to enter the main menu.

  • Page 55: Usb 2.0 Driver

    FabiaTech Corporation USB 2.0 Driver WIN 98/2000/XP Driver Step 1: To install the USB driver, insert the CD ROM into the CD ROM device, and enter DRIVER>USB>855GME>WIN2K, WINXP, WIN98_ME. Step 2: Start the "Add New Hardware" wizard in control panel (Click Start/Settings/Control Panel).

  • Page 56: Watchdog Timer

    FabiaTech Corporation Watchdog Timer This section describes how to use the Watchdog Timer, including disabled, enabled, and trigger functions. The FB2652 is equipped with a programmable time-out period watchdog timer. You can use your own program to enable the watchdog timer. Once you have enabled the watchdog timer, the program should trigger the I/O every time before the timer times out.

  • Page 57: Watchdog Timer Setting

    FabiaTech Corporation Watchdog Timer Setting The watchdog timer is a circuit that may be used from your program software to detect system crashes or hang-ups. LED1 on this CPU board is the watchdog timer indicator, which is located at the upper-left corner above the CN1 connector.

  • Page 58: Watchdog Timer Enabled

    FabiaTech Corporation Watchdog Timer Enabled To enable the watchdog timer, you have to output a byte of timer factor to the watchdog register whose address is 2Eh and data port is 2fH. The following is an Assemble program, which demonstrates how to enable the watchdog timer and set the time-out period at 28 seconds.

  • Page 59: Watchdog Timer Disabled

    FabiaTech Corporation Watchdog Timer Disabled To disable the watchdog timer, simply write a 00H to the watchdog register. ;------------------------------------------------------------------------------------------ ; Enter the extended function mode, interruptible double-write ;------------------------------------------------------------------------------------------ dx,2eh ; Enter to extended function mode al,87h dx,al dx,al ;------------------------------------------------------------------------------------------------------------------------ ; Logical device 8, configuration register CRF5 Bit 3(Sec./Min.), CRF6 Bit 0~7 (Count.) ;-------------------------------------------------------------------------------------------------------------------------...

  • Page 60: J5 Ttl I/O -Software Programming Example

    FabiaTech Corporation J5 TTL I/O -Software programming example The following example is written in Intel 8086 assembly language. It assumes that the IO port address is located at 2Eh and data port is located at 2Fh. The following is an Assemble program, which demonstrates how to read/write the TTL IO port ;------------------------------------------------------------------------------------------...

  • Page 61: Chapter 6 Technical Reference

    FabiaTech Corporation Chapter 6 Technical Reference This section outlines the errors that may occur when you operate the system, and also gives you the suggestions on solving the problems. Topic include: Trouble Shooting for Post Beep & Error Messages Technical Reference Trouble Shooting for Post Beep and Error Messages The following information informs the Post Beep &...
  • Page 62 FabiaTech Corporation CMOS CHECKSUM ERROR This error informs that the CMOS has corrupted. When the battery runs weak, this situation might happen. Please check the battery and change a new one when necessary. DISK BOOT FAILURE When you can‘t find the boot device, insert a system disk into Drive A and press <...
  • Page 63 FabiaTech Corporation MEMORY ADDRESS ERROR When the memory address indicates error. You can use this location along with the memory map for your system to find and replace the bad memory chips. MEMORY SIZE HAS CHANGED Memory has been added or removed since last boot. In EISA mode, use Configuration Utility to re-configure the memory configuration.

  • Page 64: Technical Reference

    FabiaTech Corporation Technical Reference Real-Time Clock and Non-Volatile RAM The FB2652 contains a real-time clock compartment that maintains the date and time in addition to storing configuration information about the computer system. It contains 14 bytes of clock and control registers and 114 bytes of general purpose RAM.
  • Page 65 FabiaTech Corporation Address Description Low expansion memory byte High expansion memory byte 19-2D Reserved 2E-2F 2-byte CMOS checksum Low actual expansion memory byte High actual expansion memory byte Date century byte Information flags (set during power on) 34-7F Reserved for system BIOS...

  • Page 66: Cmos Ram Map

    FabiaTech Corporation CMOS RAM Map Register Description 00h -10h Standard AT-compatible RTC and Status and Status Register data definitions 11h – 13h Varies Equipment Bits Number of Floppy Drives 1 Drive 2 Drives Bits Monitor Type Not CGA or MDA 01 40x25 CGA...

  • Page 67: I/O Port Address Map

    FabiaTech Corporation I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses, which also becomes the identity of the device. There is a total of 1K-port address space available. The following table lists the I/O port addresses used on the Industrial CPU Card.

  • Page 68: Interrupt Request Lines (Irq)

    FabiaTech Corporation Interrupt Request Lines (IRQ) There are a total of 15 IRQ lines available on the Industrial CPU Card. Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on the Industrial CPU Card.

  • Page 69: Dma Channel Map

    FabiaTech Corporation DMA Channel Map The equivalent of two 8237A DMA controllers are implemented in the FB2652 board. Each controller is a four-channel DMA device that will generate the memory addresses and control signals necessary to transfer information directly between a peripheral device and memory.

  • Page 70: Serial Ports

    FabiaTech Corporation Serial Ports The ACEs (Asynchronous Communication Elements ACE1 to ACE2) are used to convert parallel data to a serial format on the transmit side and convert serial data to parallel on the receiver side. The serial format, in order of transmission and reception, is a start bit, followed by five to eight data bits, a parity bit (if programmed) and one, one and half (five-bit format only) or two stop bits.
  • Page 71 FabiaTech Corporation Bit 1: Enable Transmitter Holding Empty Interrupt (ETBEI) Bit 2: Enable Receiver Line Status Interrupt (ELSI) Bit 3: Enable MODEM Status Interrupt (EDSSI) Bit 4: Must be 0 Bit 5: Must be 0 Bit 6: Must be 0...
  • Page 72 FabiaTech Corporation Bit 5: Stick Parity Bit 6: Set Break Bit 7: Divisor Latch Access Bit (DLAB) MODEM Control Register (MCR) Bit 0: Data Terminal Ready (DTR) Bit 1: Request to Send (RTS) Bit 2: Out 1 (OUT 1) Bit 3: Out 2 (OUT 2)
  • Page 73 FabiaTech Corporation Bit 4: Clear to Send (CTS) Bit 5: Data Set Ready (DSR) Bit 6: Ring Indicator (RI) Bit 7: Received Line Signal Detect (RSLD) Divisor Latch (LS, MS) Bit 0: Bit 0 Bit 8 Bit 1: Bit 1...

  • Page 74: Parallel Ports

    FabiaTech Corporation Parallel Ports Register Address Port Address Read/Write Register Base + 0 Write Output data Base + 0 Read Input data Base + 1 Read Printer status buffer Base + 2 Write Printer control latch Printer Interface Logic The parallel portion of the SMC37C669 makes the attachment of various devices that accept eight bits of parallel data at standard TTL level.
  • Page 75 FabiaTech Corporation Bit 7: This signal may become active during data entry, when the printer is off-line during printing, or when the print head is changing position or in an error state. When Bit 7 is active, the printer is busy and cannot accept data.
  • Page 76 FabiaTech Corporation Bit 5: Direction control bit. When logic 1, the output buffers in the parallel port are disabled allowing data driven from external sources to be read; when logic 0 they work as a printer port. This bit is write-only.

  • Page 77: Appendix

    FabiaTech Corporation Appendix Dimension 8. 1 8 .1 O 3. 5 1 46 .1...

Table of Contents