About The Tally Connectors; About The Remote Connector - Edirol V-440HD Owner's Manual

Reference

About the TALLY Connectors

When connecting a television monitor equipped with a TALLY input to the
V-440HD, you can have the television monitor's TALLY lamp light up. The
TALLY lamp lights up according to the switching status, allowing you to
confirm the channel being used on the monitor. The switching status of the
SD video is output from the TALLY 1 connector, and the switching status
of the HD/RGB video is output from the TALLY 1 (HD/RGB) connector.
* Obtain a separate cable for use in connecting the V-440HD with the
TALLY input-equipped television monitor.
About TALLY Types
The V-440HD is capable of outputting three different types of tally
signal, Type 1-Type 3. When Type 1-3 is selected, you can then select
the terminal from which the tally signals are output (refer to "TALLY
Terminal Specifications" below).
You can select the tally signal output type in "12. Tally Signal" under
"13. System" in the menu; select the output type suited to the
particular conditions.
* For more on the menus, refer to Menu Operations (p. 25).
TALLY Connector Specifications
Connector Type: D-SUB 15-pin shrink terminal
• TALLY 1 (SD) Connector Pin Assignments
Pin number Signal name
1 SD 1ch Type 1
2 SD 1ch Type 2
3 SD 1ch Type 3
4 GND
5 SD 4ch Type 1
6 SD 2ch Type 1
7 SD 2ch Type 2
8 SD 2ch Type 3
9 GND
10 SD 4ch Type 2
11 SD 3ch Type 1
12 SD 3ch Type 2
13 SD 3ch Type 3
14 GND
15 SD 4ch Type 3
• TALLY 2 (HD/RGB) Connector Pin Assignments
Pin number Signal name
1 HD/RGB 1ch Type 1
2 HD/RGB 1ch Type 2
3 HD/RGB 1ch Type 3
4 GND
5 HD/RGB 4ch Type 1
6 HD/RGB 2ch Type 1
7 HD/RGB 2ch Type 2
8 HD/RGB 2ch Type 3
9 GND
10 HD/RGB 4ch Type 2
11 HD/RGB 3ch Type 1
12 HD/RGB 3ch Type 2
13 HD/RGB 3ch Type 3
14 GND
15 HD/RGB 4ch Type 3
44
Pin Connections
5 1
10 6
15 11
Pin Connections
5 1
10 6
15 11

About the REMOTE Connector

You can use the REMOTE connector to enable switching, control of
effects, and other operations from a computer or other external
control device.
REMOTE Connector Specifications
• Transmission Format: Start-stop synchronization
(asynchronous), full duplex
• Transmission Rate: 9600 bps (Initial setting)/19200 bps
(This can be changed in the menu with "8. REMOTE Baudrate"
under "13. System" (p. 54).)
• Parity: None
• Data Length: 8 bits
• Stop Bit Length: 1 bit
• Encoding: ASCII
• Flow Control: XON/XOFF
Pin number Signal name
1 DCD
2 RXD
3 TXD
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 RI
* The V-440HD's connectors are male. To connect to a computer, use a
female-female crossover cable.
Cable Connections:
V-440HD Computer
1 : DCD 1 : DCD
2 : RXD 2 : RXD
3 : TXD 3 : TXD
4 : DTR 4 : DTR
5 : GND 5 : GND
6 : DSR 6 : DSR
7 : RTS 7 : RTS
8 : CTS 8 : CTS
9 : RI 9 : RI
Setup Procedure
Use the following procedure to set up the control device and V-
440HD.
1.
Connect the V-440HD and control device with a REMOTE
cable.
2.
Turn on the power to the control device.
3.
Set the communications protocol for the control device.
4.
Turn on the power to the V-440HD.
5.
Begin operation.
* For more on commands, refer to REMOTE Command Reference
(p. 56).
Pin Connections
5 1
9 6