Repair of the device may only be carried out by trained service personnel. Advantech recommends that a service contract be obtained with Advantech Service and that all repairs also be carried out by them. Otherwise the correct functioning of the device may be compromised.
Page 3
The equipment has been dropped and damaged. The equipment has obvious signs of breakage. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning and keep this equip- ment away from humidity.
Page 4
Caution! When servicing the device, always use replacement parts that are quali- fied to Advantech standards. Advantech Digital Healthcare cannot war- rant or endorse the safe performance of third-party replacement parts for use with our medical device.
Page 5
22. The configuration of the device should mainly be done by the user using the provided hardware keypad. 23. If software tools are provided by Advantech they should be operated using the specific instructions provided. Any software tools provided should only be installed on a computer with appropriate systems to prevent unauthorized access.
Explanation of Graphical Symbols IEC 60878 and ISO 3864-B.3.6 : Warning: dangerous voltage ISO 7000-0434 : Caution, consult ACCOMPANYING DOCUMENTS. ISO 7010-M002: Follow instructions for use. IEC 60417 -5009 : STAND-BY. IEC 60417-5031 : Direct current. IEC 60417-5021 : Equipotentiality.
Disposing of Old Products Within the European Union EU-wide legislation, as implemented in each member state, requires that waste electrical and electronic products carrying the mark shown at left must be disposed of separately from normal household waste. This includes monitors and electrical accessories, such as signal cables or power cords.
Otherwise the correct functioning of the device may be compromised. Additional Information and Assistance Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call: ...
Intended use – PDC-W240 is intended to serve for use in medical environment to monitor high quality video and graphic image. It should not be used as a life-support system.
Specifications Model PDC-W240 Viewable Diagonal (inches) Luminance (cd/m2, typical) Native Resolution 1920 x 1080 Display Dot Pitch (mm) 0.274 Vertical Viewing Angle Horizontal Viewing Angle Contrast Ratio 1000:1 (nominal) Input Port DVI; DP; HDMI; VGA Speaker Left/ Right IO port...
Page 12
Dimensions: 583 x 386 x 69 mm (Unit: mm) Figure 1.1 Dimensions of the PDC-W240 VESA Mounting: 75 x 75 mm; 100x100 mm Please use M4x12L (Maxium)screw. Figure 1.2 VESA Mounting of the PDC-W240 Warning! Use suitable mounting apparatus to avoid risk of injury.
Figure 1.3 PDC-W240 Front Panel Power Menu Enter Touchscreen Status Control DICOM/Gamma Contrast Down/ Up Cleaning and Disinfecting 1.3.1 During normal use of the PDC the device may become dirty and should be regularly cleaned. Steps: 1. Prepare cleaning water 2.
2 System Setup A Quick Tour of the PDC-W240 Before you start to set up the PDC-W240, take a moment to become familiar with the locations and purposes of the controls, drives, connections and ports, which are illustrated in the figures below.
Page 15
Figure 2-3: Rear view of Multi I/O ports 2-2 and 2-3 Rear view (1) Audio: Earphone/ Audio in (2) P-cap USB (Type B) (3) USB upstream Port (4) Power DC-IN (5) DP (6) HDMI (7) DVI (8) VGA (9) Equipotential Terminal Pin NOTE: need link to hospital ground/earth system before...
2.2.1 Connecting the Power Cord FSP065- The PDC-W240 can only be powered by a DC power adapter (FSP Model DHBM1 ). Be sure to always handle the power cords by holding the plug ends only. Follow these procedures in order: Connect the female end of the power adapter to the DC jack of the panel PC.
Page 17
Guidance and Manufacturer’s Declaration – Electromagnetic Emissions The model PDC-W240 is intended for use in an electromagnetic environment as specified below. The customer or the user of the PDC-W240 should assure that it is used in such an environment. Electromagnetic Environmen-...
Page 18
Recommended Separation Distances Between Portable and Mobile RF Communications Equipment and the PDC-W240 PDC-W240 is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the model POC -W152C can...
Page 19
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity PDC-W240 is intended for use in the electromagnetic environment specified below. The customer or the user of the model PDC-W240 should assure that it is used in such an environment. IEC 60601 Test...
Page 20
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity The model PDC-W240 is intended for use in the electromagnetic environment specified below. The customer or the user of the model PDC-W240 should assure that it is used in such an environment. Immunity...
Page 21
necessary, such as reorienting or relocating the unit. Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Thermal The vent hole of the PDC-W240 rear cover functions as a cooling air flow inlet and outlet. These air inlets and outlets transfer heat from inside the computer to the cooler air outside. Do not block these holes/vents with any soft material.
Page 23
licensed electrician to replace the outlet with a properly grounded outlet. Do not defeat the purpose of the grounding plug. Warning! Never push objects of any kind into this product through the openings in the case. Doing so may be dangerous and result in fire or a dangerous electric shock. Never place anything on system case before turning off the computer.
Revision History Revison Changes Date Initial Release 06/27/2016 Added caution to only use with approved software and recommendation to use secured 05/22/2021 network. Added revision history with dates...
Install VESA Mounting The PDC-W240 also provides standard VESA mounting to help system integrators conveniently integrate the panel PC into their system. Never use mounting brackets except as provided by Advantech to prevent unreliable mounting of the PDC-W240. VESA mount installation should be carried out by a professional technician;...
Need help?
Do you have a question about the PDC-W240 and is the answer not in the manual?
Questions and answers