Advertisement
WARNING! The welder may produce voltage surges in the mains supply which can damage other sensitive equipment
‰
(e.g. computers). To prevent this happening, it is recommended that the welder is connected to a power supply that does not
feed any sensitive equipment.
IMPORTANT! If using welder to full capacity, we recommend a 16amp supply. We recommend you discuss the installation of a
16amp industrial round pin plug and socket with your electrician.
1.2.
GENERAL SAFETY
▲
DANGER! Unplug the welder from the mains power supply before performing maintenance or service.
Keep the welder and cables in good working order and condition. Take immediate action to repair or replace damaged parts.
9
Use genuine parts and accessories only. Unapproved parts may be dangerous and will invalidate the warranty.
9
Use an air hose to regularly blow out any dirt from the liner and keep the welder clean for best and safest performance.
9
Check and spray the gas cup and contact tip regularly with anti-spatter spray, available from your Sealey stockist.
9
Locate welder in a suitable work area. Ensure that the area has adequate ventilation as welding fumes are harmful.
9
Keep work area clean, tidy and free from unrelated materials. Also ensure the working area has adequate lighting and that a fire
9
extinguisher is at hand.
WARNING! Use welding head shield to protect eyes and avoid exposing skin to ultraviolet rays given off by electric arc. Wear
‰
safety welding gauntlets.
Remove ill fitting clothing, remove ties, watches, rings and other loose jewellery and contain long hair.
9
Ensure the workpiece is correctly secured before welding.
9
Avoid unintentional contact with the workpiece. Accidental or uncontrolled use of the torch may be dangerous and will wear the nozzle.
9
Keep unauthorised persons away from the work area. Any persons working within the area must wear a protective head shield and gloves.
9
Operators must receive adequate training before using the welder.
9
Stand correctly keeping a good footing and balance, ensure the floor is not slippery and wear non-slip shoes.
9
DO NOT operate the welder if it or the cables are damaged and DO NOT attempt to fit any unapproved torches or other
8
components to the welder.
DO NOT get welder wet or use in damp or wet locations or areas where there is condensation.
8
▲
DANGER! DO NOT weld near flammable solids, liquids or gases and DO NOT weld containers or pipes which have held
flammable materials. Avoid welding materials which have been cleaned with chlorinated solvents or welding near such solvents.
DO NOT stand welder on a metal workbench, car bodywork or similar.
8
DO NOT touch any live metal parts of the torch or electrode while the machine is switched on.
8
DO NOT pull the welder by the cable, or the torch. Protect cables from sharp or abrasive items. DO NOT bend, strain or stand on cables
8
or leads.
Protect from heat. Long lengths of slack must be gathered and neatly coiled. DO NOT place cables where they endanger others.
9
DO NOT touch the torch or workpiece immediately after welding as they will be very hot. Allow to cool.
8
DO NOT operate welder while under the influence of drugs, alcohol or intoxicating medication, or if tired.
8
When not in use store the welder in a safe, dry, childproof area.
9
2. INTRODUCTION
IMPORTANT: These instructions contain the information you require to prepare your machine for welding, together with a maintenance
and a troubleshooting section. The instructions are not intended to teach you how to weld. If you have no experience, we recommend that
you seek training from an expert source. MIG welding is relatively easy, but does require a steady hand and supervised practice on scrap
metal, as it is only with continued practice that you will achieve the desired results.
One of our SUPERMIG® range, this compact no-gas welder offers excellent performance at an extremely competitive price. High output
transformer and forced-air cooling to maximize duty cycle performance. Supplied with 2m non-live torch & 1.4m earth cable. Suitable for
gasless operation only. For use with flux cored wire only. 3 Year Guarantee*. Lifetime guarantee on Transformer*.
3. SPECIFICATION
Model No: ....................................................... SUPERMIG100
Welding Current:........................................................ 40 - 100A
Wire Capacity: ............................................... 1kg Gasless only
Duty Cycle: .............. 100% @ 32A, 35% @ 54A, 10% @ 100A
Cooling System: ....................................................... Forced Air
Spot Welding Timer: ............................................................. No
Gas Type: ............................................................................N/A
Torch: .................................................................... 2m Non-Live
Supply: ............................................................................. 230V
Absorbed Power: ............................................................ 3.3kW
Case Size: .................................................................. Compact
4. ASSEMBLY
4.1.
FIT HANDLE: Slide handle onto top cover. Secure with screw (19), see Parts Diagram.
4.2.
FIT COVER LOCKING SPRING: Fix Cover Locking Spring (8), see Parts Diagram, to top of front panel. Use screw, washer and spring
washer supplied. See also fig.1.A.
4.3.
FITTING A REEL OF WIRE
4.3.1.
Depress the silver button in the front of the handle and open the top compartment. See A & B in fig.1.
4.3.2.
Referring to fig.2, rotate the butterfly nut (5) anti-clockwise and remove it from the threaded spindle together with the pressure disc (4).
Leave the spring (1) on the spindle (2).
4.3.3.
Place the wire reel (3) over the spindle and down onto the spring ensuring that the wire will withdraw from the spool in a forwards
direction and on the same side of the compartment as the wire feed unit.
4.3.4.
Push lightly down on the top of the reel of wire and screw the pressure disc (4) onto the end of the spindle and down onto the top of
the wire reel. The reel take off pressure should be set to provide a mild braking effect to prevent overrun where loose coils of wire form
on the reel. DO NOT over tighten the pressure disc as too much braking will conflict with the wire tension set on the wire drive unit.
© Jack Sealey Limited
Original Language Version
SUPERMIG100
Issue 2 (4,F) 03/05/23
Advertisement
