Page 1
Model 8621 Telescopic Crane Owner’s Manual Installation • Assembly Drawings • Parts Notice: A copy of this manual must remain with the equipment at all times. For a printable download copy, please visit: www.stellarindustries.com Stellar Industries, Inc. 190 State Street...
Page 2
MADE IN THE U.S.A. BY STELLAR INDUSTRIES, INC. PN C5942 M OD E L N O . S ER IA L NO . MADE IN THE U.S.A. BY STELLAR INDUSTRIES, INC. PN C5942 Page ii | Stellar 8621 Telescopic Crane Owner’s Manual PN: 118497 ®...
800-321-3741 Hours: Monday - Friday, 8:00 a.m. - 5:00 p.m. CST Or email at the following addresses: Technical Questions, and Information service@stellarindustries.com Order Parts parts@stellarindustries.com Warranty Information warranty@stellarindustries.com Page iv | Stellar 8621 Telescopic Crane Owner’s Manual PN: 118497 ®...
38.6” (98 CM) REQUIRED MOUNTING SPACE 20” X 21” (50.8 CM X 53.3 CM) APPROXIMATE CRANE WEIGHT 8621 HSS STANDARD: 1,580 LBS (717 KG) CONTROLS RADIO CONTROL STANDARD FOR ALL FUNCTIONS. WIRE ROPE 3/8” (0.95 cm)6X31 IWRC-DGXIP X 100’ (30.48 m) BOOM ELEVATION -10º...
General Installation This chapter is designed to serve as a general guide for the installation of a Stellar 8621 Crane on a Stellar Service Body. Each installation is considered unique so certain portions of this chapter may or may not apply to your direct application.
Installation Overview 1. Determine that the mounting location for the 8621 is at least 18” x 20” (45.7 x 50.8 cm). 2. Use the detail below to drill 1.06” diameter holes into the mounting plate. Run tap on the threads of the base to be sure they are clean.
Page 15
This Page Left Intentionally Blank. Stellar 8621 Telescopic Crane Owner’s Manual PN: 118497 | Page 11 ®...
#2 / RED SUPPLY (+) 12V/24V #3 / GRN ALARM DISABLE GND INPUT OPTION OUTPUT NOTICE Any modification to the crane control system (electrical and/or hydraulic) must be approved by Stellar. Page 12 | Stellar 8621 Telescopic Crane Owner’s Manual PN: 118497 ®...
Be sure to grind the frame rail around the hole to ensure a proper ground connection. • Frame rail thickness may require additional flat washers (as shown). • Use an electrical coating on hardware to prevent corrosion. Page 14 | Stellar 8621 Telescopic Crane Owner’s Manual PN: 118497 ®...
Page 19
This page left intentionally blank. Stellar 8621 Telescopic Crane Owner’s Manual PN: 118497 | Page 15 ®...
6. Connect the second end of the winch case drain to unshared fitting on the top of the reservoir as shown in Fig 2. Fig.1 Fig. 2 3/8” Line 1/2” Line 1/4” Line Stellar 8621 Telescopic Crane Owner’s Manual PN: 118497 | Page 23 ®...
The radio can only be put into stability mode five times. After that, the radio would have to be returned to Stellar to be reprogrammed to allow additional stability testing. All other radio functions will work properly even if stability mode is not available. Stellar 8621 Telescopic Crane Owner’s Manual PN: 118497 | Page 25 ®...
If level indicator is missing or damaged, please contact Stellar Customer Support for a replacement. PN 76483 Page 26 | Stellar 8621 Telescopic Crane Owner’s Manual PN: 118497 ®...
CDT PRO NONBOOST ONLY - Valve controller inside mast 124609 DECAL CNTRL ID 8621 V3 CDT PRO NB * For CDTpro™ equipped cranes, use PN 118538. For CDTprononboost™ equipped cranes, use PN 124609. ** Not shown. Stellar 8621 Telescopic Crane Owner’s Manual PN: 118497 | Page 27 ®...
Page 32
This page left intentionally blank. Page 28 | Stellar 8621 Telescopic Crane Owner’s Manual PN: 118497 ®...
MOTOR HYD ROSS MK080613AAAB 104018 HARDWARE KIT BASE ASM 30IN GREASE LINE 53495 CAP SCR 0.50-13X2.00 SH 21151 GASKET MOTOR 008-10056-1 REV. D NOTE: ITEM 1 INCLUDES GUARD & GUARD FASTENERS. Stellar 8621 Telescopic Crane Owner’s Manual PN: 118497 | Page 31 ®...
Need help?
Do you have a question about the 8621 and is the answer not in the manual?
Questions and answers