Table of Contents
Advertisement
Contents
Contents
1
Safety .................................................................... 3
1.1
Action-related warnings ......................................... 3
1.2
Intended use ......................................................... 3
1.3
Risk caused by inadequate qualifications.............. 3
1.4
Risk of death from electric shock........................... 3
1.5
Risk of death due to lack of safety devices ........... 3
1.6
materials ................................................................ 3
1.7
components ........................................................... 4
1.8
surface ................................................................... 4
1.9
product................................................................... 4
1.10
Risk of material damage caused by frost .............. 4
1.11
unsuitable tool........................................................ 4
1.12
is too hard .............................................................. 4
1.13
unsuitable room air ................................................ 4
1.14
supply .................................................................... 4
1.15
Structural damage due to escaping water ............. 4
1.16
Regulations (directives, laws, standards) .............. 5
2
Notes on the documentation .............................. 6
2.1
Observing other applicable documents ................. 6
2.2
Storing documents................................................. 6
2.3
Validity of the instructions ...................................... 6
3
Product description............................................. 7
3.1
Basic system diagram............................................ 7
3.2
Product design....................................................... 8
3.3
Operation ............................................................... 8
3.4
Type designation and serial number ..................... 8
3.5
CE marking ............................................................ 8
4
Set-up.................................................................... 8
4.1
4.2
Carrying the product .............................................. 9
4.3
Unpacking the product........................................... 9
4.4
Checking the scope of delivery.............................. 9
4.5
dimensions........................................................... 10
4.6
Minimum clearances............................................ 11
4.7
Requirements for the installation site .................. 11
4.8
Removing/installing the protective cover ............. 11
5
Installation.......................................................... 11
5.1
Installing the air supply and air exhaust .............. 12
5.2
Installing the water connections .......................... 14
5.3
Electrical installation ............................................ 15
6
Start-up ............................................................... 17
6.1
Filling the domestic hot water circuit.................... 17
6.2
Establishing the power supply ............................. 17
6.3
Switching on the product ..................................... 17
2
7
Handing the product over to the operator ...... 18
8
Adapting the unit to the installation ................ 18
8.1
Calling up the installer level ................................. 18
8.2
Optimising the unit's energy consumption ........... 18
8.3
Activating and setting photovoltaic mode ............ 18
8.4
Reading the input data......................................... 19
8.5
Setting the anti-legionella function....................... 19
8.6
Selecting the load relief stage ............................. 19
8.7
Setting the minimum temperature ....................... 19
8.8
Setting ventilator mode ........................................ 20
8.9
Setting the maximum heating time ...................... 20
8.10
Reading the meter status .................................... 20
8.11
Locking the control elements ............................... 20
8.12
Checking the immersion heater ........................... 21
9
Troubleshooting ................................................ 21
9.1
Eliminating faults.................................................. 21
9.2
Resetting parameters to factory settings ............. 21
9.3
Resetting the safety cut-out ................................. 21
9.4
Replacing the mains connection cable ................ 22
9.5
Completing repair work........................................ 22
10
Inspection and maintenance ............................ 22
10.1
Preparing the maintenance and repair work........ 22
10.2
intervals ............................................................... 22
10.3
Draining the product ............................................ 22
10.4
Procuring spare parts .......................................... 22
11
Decommissioning.............................................. 22
11.1
Decommissioning the product ............................. 22
11.2
Arranging disposal of refrigerant ......................... 22
12
Customer service............................................... 23
13
Recycling and disposal..................................... 23
Appendix ............................................................................ 24
Overview............................................................. 24
Fault messages - Overview.............................. 24
Installer level - Overview .................................. 26
Electronics box wiring diagram ....................... 28
Basic hydraulic diagram ................................... 29
Heat pump output curves ................................. 29
Technical data.................................................... 30
Index ................................................................................... 32
Installation and maintenance instructions aroSTOR 0020290840_00
- Quick Links:
- B Fault Messages - Overview
Hide quick links:
Advertisement
Table of Contents
