Download Print this page

Tiger JD6M MY20 Mounting And Operating Instructions

Side rotary w/ independent hydraulics

Advertisement

Quick Links

PARTS LISTING WITH
MOUNTING AND OPERATING
INSTRUCTIONS
JD6M MY20
SIDE ROTARY
w/ INDEPENDENT
Current as of 3/10/2021
Tiger Corporation
3301 N. Louise Ave.
Sioux Falls, SD 57107
1-800-843-6849
1-605-336-7900
www.tigermowers.com
HYDRAULICS
06011060

Advertisement

loading

Summary of Contents for Tiger JD6M MY20

  • Page 1 JD6M MY20 SIDE ROTARY w/ INDEPENDENT HYDRAULICS Current as of 3/10/2021 PARTS LISTING WITH MOUNTING AND OPERATING INSTRUCTIONS Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www.tigermowers.com 06011060...
  • Page 2 TO THE OWNER / OPERATOR / DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.
  • Page 3 • Classify the problem • Hydraulic, electrical or mechanical - Read the trouble shooting section • Tractor or Truck chassis - Contact vehicle dealer • If unable to correct the problem yourself, contact your local Tiger Dealer after gathering: • Machine model _______________________ •...
  • Page 5: Table Of Contents

    PARTS SECTION______________________________________ COMMON PARTS SECTION____________________________ WARRANTY INFORMATION_____________________________ This symbol means: CAUTION – YOUR SAFETY IS AT RISK! When you see this symbol, read and follow the associated instructions carefully or personal injury or damage may result. Tiger is a registered trademark.
  • Page 7: Safety Section

    SAFETY SECTION...
  • Page 8 SAFETY General Safety Instructions and Practices A safe and careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to the owner / operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions. The first section of this manual includes a list of Safety Messages that, if followed, will help protect the operator and bystanders from injury or death.
  • Page 9 SAFETY Si no lee Ingles, pida ayuda a alguien que PELIGRO! LEA EL si lo lea para que le traduzca las medidas INSTRUCTIVO! de seguridad. (SG-3) Never operate the Tractor or Implement until you have read and DANGER! completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Messages found in the Manual or on the Tractor and Implement.
  • Page 10 SAFETY Never allow children or other persons to ride on the Tractor or Implement. DANGER! Falling off can result in serious injury or death. (SG-10) DANGER! Never allow children to operate or ride on the Tractor or Implement. (SG-11) WARNING! Do not mount the Tractor while the tractor is moving.
  • Page 11 SAFETY WARNING! The operator and all support personnel should wear hard hats, safety shoes, safety glasses, and proper hearing protection at all times for protection from injury including injury from items thrown by the equipment. (SG-16) CAUTION! PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PER- MANENT HEARING LOSS! Tractors with or without an Implement attached can often be noisy enough to cause permanent hearing loss.
  • Page 12 SAFETY WARNING! Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. Make sure the tractor engine is off before working on the Implement. (SG-20) WARNING! Periodically inspect all moving parts for wear and replace when necessary with authorized service parts.
  • Page 13 SAFETY CAUTION! On a fully-assembled unit, do not remove the Wing Retaining Strap until hoses are attached to the tractor and the Wing Cylinders are filled with oil. Lower the Wings slowly and carefully. Keep bystand- ers away during operations. (STI-5) DANGER! NEVER use drugs or alcohol immediately before or while operating the...
  • Page 14 SAFETY DANGER! The rotating parts of this machine have been designed and tested for rugged use. However, the blades could fail upon impact with heavy, solid objects such as metal guard rails and concrete structures. Such impact could cause the broken objects to be thrown outward at very high velocities.
  • Page 15 SAFETY Rotary Mowers are capable under adverse conditions of throwing DANGER! objects for great distances (100 yards or more) and causing serious injury or death. Follow safety messages carefully. STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UN- LESS: -Front and Rear Deflectors are installed and in good, working condition;...
  • Page 16 SAFETY WARNING! Never leave the Tractor and Implement unattended while the Implement is in the lifted position. Accidental operation of lifting lever or a hydraulic failure may cause sudden drop of unit with injury or death by crushing. To properly park the implement when disconnecting it from the tractor, lower the stand and put the retaining pin securely in place, or put a secure support under the A-Frame.
  • Page 17 These parts are made and tested to Tiger specifications. Non-genuine “will fit” parts do not consistently meet these specifications. The use of “will fit” parts may reduce mower performance, void mower warranties and present a safety hazard. Use genuine Tiger mower parts for economy and safety. SEE YOUR...
  • Page 18 SAFETY Side Rtry Safety Section 1-12...
  • Page 19 DESCRIPTION 22839 INSTRUCT Don Not Lubricate With Automatic Grease Gun 22840 WARNING Foreign Objects Contacted 24028 WARNING Inspect Rear Flap 31522 LOGO TIGER MOWERS 31523 LOGO TIGER MOWERS 42350 DANGER Cuttershaft Direction 33743 INSTRUCT Mowing Safet Tips 42399 REFLECT Red Reflector...
  • Page 20 SAFETY PART NO. LOCATION 22839 MOWER DECK 22840 INSIDE OF CAB 24028 MOWER DECK 10"X5.5" 31522 MOWER DECK 18.25"X10" 31523 HYDRAULIC TANK Side Rtry Safety Section 1-14...
  • Page 21 SAFETY PART NO. LOCATION 42350 MOWER DECK 33743 INSIDE OF CAB 42399 MOWER DECK 42400 MOWER DECK Side Rtry Safety Section 1-15...
  • Page 22 SAFETY PART NO. LOCATION 6T3217 MOWER DECK 6T3219 INSIDE OF CAB 6T3220 FRONT PUMP MOUNT 6T3221 INSIDE OF CAB 29-6T3221 Side Rtry Safety Section 1-16...
  • Page 23 SAFETY PART NO. LOCATION 6T3233 INSIDE OF CAB 6T3234 INSIDE OF CAB 6T3236 MOWER DECK 6T3243 INSIDE OF CAB Side Rtry Safety Section 1-17...
  • Page 24 SAFETY PART NO. LOCATION 6T3233 HYDRAULIC TANK 6T3234 INSIDE OF CAB 6T3236 MOWER DECK HYDRAULIC TANK 6T3243 INSIDE OF CAB Side Rtry Safety Section 1-18...
  • Page 25 SAFETY PART NO. LOCATION 6T3249A MOWER DECK 6T3261 MOWER DECK TB1011 MOWER DECK 02962764 MOWER DECK DRAFT BEAM Side Rtry Safety Section 1-19...
  • Page 26 SAFETY PART NO. LOCATION 02965262 DRAFT BEAM 02967827 CAB FENDER Side Rtry Safety Section 1-20...
  • Page 27 SAFETY 34852 HYDRAULIC TANK 00756059 MOWER DECK Side Rtry Safety Section 1-21...
  • Page 28 SAFETY ITEM PART NO. QTY. DESCRIPTION 50023 AVAIL MANUAL CANISTER COMPLETE 00776031 Round Manual Canister 33997 Decal, Sheet, Manual Canister Decal Decal Decal AVAIL Specification Product Manual 33753 EMI Safety Manual 34296 Front Adhesive Pad 34297 Rear Adhesive Pad 6T1823 Zip Tie 14"...
  • Page 29 SAFETY FEDERAL LAWS AND REGULATIONS This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such.
  • Page 30 SAFETY Side Rtry Safety Section 1-24...
  • Page 31: Assembly / Mounting Section

    JD6M MY20 SIDE ROTARY with INDEPENDENT HYDRAULICS ASSEMBLY SECTION Assembly Section 2-1...
  • Page 32 Always use a floor jack, hoist or fork lift to lift and raise heavy parts. Read and understand the entire Assembly Section instructions before attempting to mount your Tiger mower. Refer to the Parts Section of this manual for detailed illustrations to locate all parts.
  • Page 33 ASSEMBLY FRONT CRANKSHAFT PULLEY Tiger has found that the front crankshaft pulley used by John Deere will not allow for the installation of a front drive system. You will need to order a different pulley, washer and bolt from John Deere to allow for a front drive to be installed on your tractor.
  • Page 34 ASSEMBLY DRIVESHAFT AND FRONT PUMP MOUNTING Install spacer plate on tractor engine using bolts and lockwashers as shown in Parts Section. Grease sleeve section of the driveshaft and install from the side of the engine compartment. Once you have the sleeve section in place, bolt to spacer plate using bolts and lockwashers as shown in Parts Section.
  • Page 35 ASSEMBLY APPLICATION OF LOCTITE 2047 MOWER MAINFRAME MOUNTING BOLTS All mower mainframe mounting bolts shall be secured utilizing Loctite 2047 and torqued per the Torque Chart in the maintenance section. Shake bottle for 60 seconds before use. To prevent clogging of nozzle, do not allow tip to touch metal surfaces during application.
  • Page 36 ASSEMBLY SWITCHBOX WIRING Power for the switchbox is accessed through the port located on the right rear of the cab. A John Deere plug is used, part number RE67651. DO NOT connect the plug to the cab port until the wiring is completed. The wires in the plug are colored RED, BLACK and ORANGE. IMPORTANT: The hot wire will be the RED wire or the ORANGE wire.
  • Page 37 The solenoid switch is mounted near the battery behind the steps on the right side of the tractor.(see photos below). Secure with hardware provided. (ASM-JD-0083 JD6M MY20) . Route wires to and from the Continuous Duty Solenoid Switch as shown below.
  • Page 38 3/8” holes. Use a 1” hole saw and cut a 1” hole through the mat over each 3/8” hole. Secure the stand to the floor with the spacers, capscrews and nylock nuts provided. (ASM-JD6M MY20 CABLE CONTROL) Assembly Section 2-8...
  • Page 39 ASSEMBLY VALVE MOUNTING Remove the plug from the second port in the rear of the Husco valve and place it in the port in the front of the valve. Secure the valve bracket to the tractor with hardware shown in the Parts Section of the manual.
  • Page 40 ASSEMBLY 6110-30M/R VALVE MOUNTING The mounting bracket for JD 6110-30M/R series tractors features two long legs which need to be attached as shown in the photo below. Secure the bracket to the tractor with hardware shown in the Parts Section of the manual. Center the Danfoss valve on the valve plate. Align the holes on the valve with the plate holes and secure the lift valve on top of the mounting plate.
  • Page 41 Re-attach the fuel tank support tube to the left riser. Use the hardware from the toolbox mounting bracket to use while installing cooler. See the Parts Section for details of cooler installation. (ASM-JD6M MY20 NEW SIDE COOLER Assembly Section 2-11...
  • Page 42 (ASM-C-0103) FILLING HYDRAULIC RESERVOIR Refer to the Maintenance Section for filling specifications and hydraulic oil requirements. NOTE: Starting or running your Tiger mower before filling reservoir will cause serious damage to the hydraulic pump. (ASM-C-0004hydro resrv) Assembly Section 2-12...
  • Page 43 ASSEMBLY WHEEL WELL HOSE ROUTING Hoses travel along the right hand wheel well from the lift valve to the mainframe and boom. Hose clamps #06520536 are used to route the hoses as shown below. Clamps 1 and 2 (near the lift valve) use 1/4”...
  • Page 44 ASSEMBLY HOSE COVERING Secure hoses together with zip ties wherever loose. Wrap the hoses between the swivel and main boom with the hose cover provided. Wrap the hoses between the main boom and secondary boom with the hose cover provided. Where hoses may contact the frame or other edges, wrap with split hose and secure with hose clamps or zip ties.
  • Page 45 ASSEMBLY DRAFT BEAM INSTALLATION Install ½” O-ring breather into butt port of inboard cylinder. Install fittings in the rod end of the cylinder according to the diagram in the Common Parts section. These fittings should be positioned to face the butt end of the cylinder. Next turn the clevis onto the rod of the cylinder until it is tight against the shoulder and lock into place with locking bolt on clevis.
  • Page 46 ASSEMBLY FINAL PREPARATION FOR OPERATION Place operator’s safety and operation decals on the steering column and side console where they are clearly visible to the operator. These decals should be understood by each operator of the machine in conjunction with the Safety and Operation Sections of this book. The decals are to be maintained in good condition as a reminder to the operator, and should be replaced if damaged.
  • Page 47: Operation Section

    OPERATION SECTION Operation Section 3-1 © 2013 Alamo Group Inc.
  • Page 48 TIGER SIDE ROTARY MOWER OPERATING INSTRUCTIONS Tiger Side Rotary Mowers are manufactured with quality material by skilled workers. The side mower positions may optionally be controlled with the tractors remote hydraulic connections or a combination of lift valve and remote hydraulics. If so, determine which position of the mower is to be controlled by each remote lever. The mower is equipped with safety warning decals, protective deflectors, shields, and other safety features to provide operator and passerby protection, however, no shielding is 100% accurate.
  • Page 49 OPERATION 1. STANDARD EQUIPMENT AND SPECIFICATIONS SIDE ROTARY Cutting Width 60” and 72” Actual Cut Spindle Drive Direct Spline and Direct Flexible Coupler Cutter Assembly One-piece formed dish type with one-piece forged spindle assembly Cutter Head Arc 180° on Cable Lift and 159° on Combo Draft Beam Knives Two full swinging high suction heat treated knives standard Optional three, four or six knives available...
  • Page 50 OPERATION 2. OPERATOR REQUIREMENTS Safe operation of the unit is the responsibility of a qualified operator. A qualified operator has read and understands the implement and tractor Operator’s Manuals and is experienced in implement and tractor operation and all associated safety practices. In addition to the safety messages contained in this manual, safety signs are affixed to the implement and tractor.
  • Page 51 OPERATION 3. TRACTOR REQUIREMENTS In addition to tractor horsepower and size required to operate the boom unit, the tractor must also be properly equipped to provide operator protection, to alert approaching vehicle drivers of the tractor’s presence, and to ensure tractor stability when mowing with the boom fully extended. Tractor Requirements and Capabilities •...
  • Page 52 OPERATION 3.4 Front End Weight A minimum of 20% total tractor weight must be maintained on the tractor front end at all times. Front end weight is critical to maintain steering control and to prevent the tractor from rearing up while driving. If the front end is too light, add weight until a minimum of 20% total weight is reached on the front tires.
  • Page 53 OPERATION 4.2 Dismounting the Tractor Before dismounting, park the tractor and implement on a reasonably level surface, apply the parking brake, idle the engine down and lower the implement to the ground. Shut down the tractor engine according to the operator’s manual, remove the key, and wait for all motion to completely stop.
  • Page 54 OPERATION Never run the Tractor engine in a closed building or without adequate ventilation. The exhaust fumes can be hazardous to your health. (SG-23) Start tractor only when properly seated in the Tractor seat. Starting a tractor in gear can result in injury or death. Read the Tractor operator’s manual for proper starting instructions.
  • Page 55 OPERATION Do not operate this Equipment with hydraulic oil or fuel leaking. Oil and fuel are explosive and their presence could present a hazard. Do not check for leaks with your hand! High-pressure oil streams from breaks in the line could penetrate the skin and cause tissue damage including gangrene.
  • Page 56 OPERATION 7.1 Tractor Pre-Operation Inspection/Service Refer to the tractor operator’s manual to ensure a complete pre-operation inspection and scheduled service is performed according to the manufacturer’s recommendations. The following are some of the items that require daily service and inspection: •...
  • Page 57 OPERATION Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have attaching hardware. Serious injury may occur from not maintaining this machine in good working order.
  • Page 58 OPERATION HYDRAULIC LINE INSPECTION • Check hydraulic leaks along hoses, cylinders and fittings. IMPORTANT: DO NOT use your hands to check for oil leaks. Use a piece of heavy paper or cardboard to check for hydraulic oil leaks. • Inspect the condition of the valve weldment. •...
  • Page 59 OPERATION HYDRAULIC PUMP/OIL RESERVOIR • Check oil reservoir level and oil condition. (Add specific type oil if low) • Change hydraulic oil filter and hydraulic oil according to maintenance schedule. • Ensure there are no oil leaks and fitting are properly connected •...
  • Page 60 OPERATION ROTARY HEAD INSPECTION • Inspect blades and blade bolts for looseness and excessive wear. Rotate to 90° to make for checking easier. Replace damaged, worn, and missing blades as complete sets to maintain rotary balance. • Ensure blade carrier nuts are torqued to proper specifications.
  • Page 61 OPERATION 7.2 Cutting Component Inspection Inspect blade pan and blade assembly for the following: OPS-U-0031 Inspect the Blades daily for abnormal wear. REPLACE BOTH BLADES on that carrier IMMEDIATELY if either blade has: • Become bent or deformed from it’s original shape or •...
  • Page 62 OPERATION 7.3 Blade Bolt Inspection Inspect Blade Bolt Head daily for wear as followed: Inspect the Blade Bolt Heads daily for abnormal wear. REPLACE BOTH BLADE BOLTS on the Blades IMMEDIATELY if either blade bolts has: • Visible cracks or •...
  • Page 63 OPERATION Tractor PRE-OPERATION Inspection Mower ID#________________ Make ____________________ Date: ________________ Shift ____________________ Before conducting the inspection, make sure the tractor engine is off, all rotation has stopped and the tractor is in park with the parking brake engaged. Make sure the mower is resting on the ground or securely blocked up and all hydraulic pressure has been relieved.
  • Page 64 OPERATION Side Rotary Mower PRE-OPERATION Inspection Mower ID#________________ Make ____________________ Date: ________________ Shift ____________________ Before conducting the inspection, make sure the tractor engine is off, all rotation has stopped and the tractor is in park with the parking brake engaged. Make sure the mower is resting on the ground or securely blocked up and all hydraulic pressure has been relieved.
  • Page 65 OPERATION DRIVING THE TRACTOR AND IMPLEMENT Safe tractor transport requires the operator possess a thorough knowledge of the model being operated and precautions to take while driving with an attached implement. Ensure the tractor has the capacity to handle the weight of the implement and the tractor operating controls are set for safe transport.
  • Page 66 OPERATION 7.4 Starting the Tractor The procedure to start the tractor is model specific. Refer to the tractor operator’s manual for starting procedures for your particular tractor. Consult an authorized dealer if the starting procedure is unclear. Ensure the 3-point control lever is in the lowered position and the PTO is disengaged before starting the tractor.
  • Page 67 OPERATION 7.6 Driving the Tractor and Implement Start off driving at a slow speed and gradually increase your speed while maintaining complete control of the tractor and unit. Moving slowly at first will also prevent the tractor from rearing up and loss of steering control. The tractor should never be operated at speeds that cannot be safely handled or which will prevent the operator from stopping quickly during an emergency.
  • Page 68 OPERATION Inclines and ditches should be approached along a line which is at an angle as shown. This type of path will reduce the possibility of resulting damage. If the gradient is so steep that such an approach increases the possibility of a tractor roll-over, select an alternate crossing path.
  • Page 69 OPERATION Many varied objects, such as wire, cable, rope, or chains, can become entangled in the operating parts of the mower head. These items could then swing outside the housing at greater velocities than the blades. Such a situation is extremely hazardous and could result in serious injury or even death.
  • Page 70 OPERATION Rotary Mowers are capable under adverse conditions of throwing objects for great distances (300 feet or more) and causing serious injury or death. Follow safety messages carefully. STOP MOWING IF PASSERSBY ARE WITHIN 300 Feet UNLESS: -Front and Rear Deflectors, Chain Guards, or Bands are installed and in good, workable condition;...
  • Page 71 OPERATION 8.3 Ground Speed Ground speed for mowing will depend upon the height, type, and density of vegetation to be cut. Recommended speed for efficient mower performance is between 2 and 5 mph(3-8 kph). Operate the mower at the proper speed to maintain blade speed for a clean cut. Refer to the tractor operator’s manual or the tractor instrument panel for the engine speed and gear to provide the desired ground speed.
  • Page 72 OPERATION MOWER LIFT The handle nearest the center of the tractor, actuates the Lift Cylinder (Inboard). Pulling the valve handle back, towards the operator, causes the Lift Cylinder to raise the Extension Arm. If the handle is released, the valve will automatically return to center and the Extension Arm will be locked in place.
  • Page 73 OPERATION MEASUREMENT OF HEAD PITCH 1. CUT MOWER OFF AND ALLOW BLADES TO STOP ROTATING 2. Move machine to a flat, level area such as a concrete slab 3. Lower mower head to within several inches of the ground but do not rest head on ground. 4.
  • Page 74 OPERATION 9.1 Basic Troubleshooting Guide for First Start-up. a. Electrical solenoid valve does not work - check wiring, possible faulty switch, possible faulty solenoid. b. Pump is making noise - check for obstruction in suction hose and tank suction assembly, check alignment of pump driveshaft.
  • Page 75 OPERATION 9.2 Control Location and Functions The side mower height is controlled with a two or three spool valve and is coordinated as shown below. The optional three spool valve allows for the operation of a rear rotary mower or side ditcher. If the unit is equipped with a three spool valve, do not operate the third spool handle unless a rear rotary or ditcher is mounted.
  • Page 76 OPERATION 9.3 Operating the Mower Only operate the mower from the tractor operator’s seat with the seatbelt securely fastened. The tractor must be equipped with a ROPS in the raised position or a ROPS cab. The mower is designed to cut vegetation up to 2” in diameter. Sharp blades will produce a cleaner cut and require less power.
  • Page 77 OPERATION When rotating parts are in motion, serious injury may occur if caution is not used or danger is not recognized. Never allow bystanders within 300 feet of the machine when in operation. Extreme care should be taken when operating near loose objects - such as gravel, rocks and debris.
  • Page 78 OPERATION When encountering a very severe condition which causes the tractor to stall, disengage mower, start tractor, raise the mower from the cut. Shut tractor off and inspect the mower, blades and disk for damage before engaging mower again. If the blades jam or stop, disengage the clutch and raise the head slightly or back the tractor up. Normally, this will clear the cutter head.
  • Page 79 OPERATION All Safety Shields, Guards and Safety devices including (but not limited to) - the Deflectors, Chain Guards, Steel Guards, Gearbox Shields, PTO integral shields, and Retractable Door Shields should be used and maintained in good working condition. All safety devices should be inspected carefully at least daily for missing or broken components.
  • Page 80 OPERATION 9.4 Shutting Down the Implement To shut down attached mower head, first bring the tractor to a complete stop. Decrease engine RPM to idle then disengage cutterhead. The mower head will come to a complete stop within a suitable amount of time.
  • Page 81 OPERATION Always shut the Tractor completely down, place the transmission in park, and set the parking brake before you or anyone else attempts to connect or disconnect the Implement. (SRM-20) 11. MOWER STORAGE It is recommended that the mower be stored with the mower fully lowered to ground level. If the mower is stored in the raised position, select a level area and place blocks under the mower to prevent the mower from falling BEFORE disconnecting the mower from the tractor.
  • Page 82 OPERATION Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in such a way as to be clearly visible and legible. When transporting the Equipment use the Tractor flashing warning lights and follow all local traffic regulations. (SG-6) 12.1 Transporting Mower TRANSPORTING UNDER THE UNIT’S OWN POWER When transporting between job sites or between cutting passes, the following procedure should be followed:...
  • Page 83 OPERATION Next, cap or plug the hose ends and the ports on the solenoid valve and motor. For a cable lift mower disconnect the lift cable from the head and secure the loose end back onto the cable with the cable clevis. For a combo lift mower, disconnect the linkage from the mower and replace the pin and hardware with the draft beam to prevent loss.
  • Page 84 OPERATION The SMV (Slow-Moving Vehicle) emblem is universal symbol used to alert drivers of the presence of equipment traveling on roadways at a slow speed. SMV signs are a triangular bright orange with reflective red trim for both easy day and night visibility.
  • Page 85 OPERATION Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in such a way as to be clearly visible and legible. When transporting the Equipment use the Tractor flashing warning lights and follow all local traffic regulations. (SG-6) Reduce speed before turning or applying the brakes.
  • Page 86 OPERATION Use adequately sized and rated trailers and equipment to transport the tractor and implement. Consult an authorized dealer to determine the proper equipment required. Using adequately sized chains, heavy duty straps, cables and/or binders, securely tie down both the front and rear of the tractor utilizing the proper tie down locations as specified by the tractor manufacturer.
  • Page 87 OPERATION TROUBLESHOOTING GUIDE HYDRAULIC CYLINDER NOT WORKING - Check level of hydraulic fluid (see sight gauge on tank). Check to see if pump is functioning properly by attempting to use another cylinder or pressure gauge. If pump is working properly, check the pressure on the line. The relief valve may be by-passing fluid at too low pressures. If cylinder is still not functioning properly, check the line for stoppage.
  • Page 88 OPERATION SIDE ROTARY Operation Section 3-42 © 2014 Alamo Group Inc.
  • Page 89: Maintenance Section

    MAINTENANCE SECTION Maintenance Section 4-1 © 2017 Alamo Group Inc.
  • Page 90 Regular maintenance at the intervals mentioned will result in the maximum efficiency and long life of the Tiger Mower. When you purchase a Tiger Mower you also acquire another valuable asset, Tiger’s parts organization. Our rapid and efficient service has guaranteed the customer satisfaction for many years.
  • Page 91 MAINTENANCE Do not modify or alter this Implement. Do not permit anyone to modify or alter this Implement, any of its components or any Implement function. (SG-8) Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement. Place the Mower Head on the ground or securely supported on blocks or stands, disengage the PTO, and turn off the engine.
  • Page 92 MAINTENANCE REGULAR MAINTENANCE The intervals at which regular servicing should be done are based on hours of operation. Use the tractors hour meter to determine when regular servicing is required. Daily or Every 8 Hours ITEM SERVICE COMMENTS Drive Shaft Yoke, U-Joint Grease Grease as instructed in &...
  • Page 93 MAINTENANCE WEEKLY OR EVERY 40 HOURS ITEM SERVICE COMMENTS Rotary Spindle Lubricate Every 40 hours or weekly WEEKLY OR EVERY 50 HOURS ITEM SERVICE COMMENTS In Tank Hydraulic Fluid Change Change after first 50 hours only Filter (10 micron filter) then every 500 hours or yearly In-Line High Pressure Change...
  • Page 94 MAINTENANCE YEARLY OR EVERY 500 HOURS ITEM SERVICE COMMENTS Spindle Grease Change Motor to Spindle Spline Change Hydraulic Tank Fluid Change In Tank Hydraulic Fluid Filter Change (10 micron filter) In-Line HP Filter Change Change when indicated (10 micron filter) by restriction indicator.
  • Page 95 MAINTENANCE TROUBLESHOOTING SYMPTOMS CAUSE REMEDY Vibration Loose Bolts Check all bolts and tighten to recommended torque specifications in this section Cutter assembly a. Check for damaged blades, disc, unbalanced or cutter shaft. b. Replace if needed. c. Check for wire, rope, etc. entangled in the cutter assembly Mower will not lift Hydraulic Fluid Low...
  • Page 96 MAINTENANCE TROUBLESHOOTING (CONTINUED) b. Remove the four bolts holding the small block to the main block. Lift and remove small block being careful not to damage O- rings/filter. c. Clean filter and re-install. d. Remove large nut on side of large valve block.
  • Page 97 MAINTENANCE TORQUE SPECIFICATIONS SIDE ROTARY Maintenance Section 4-9 © 2017 Alamo Group Inc.
  • Page 98 Lithium-Complex Mobilgrease CM-S U-joint & Stub Shaft Extreme Pressure NLGI 2 - ISO 320 Deck Spindle (Rotary) Grease Gun Tiger Part Spindle Lubricant Mobilith SHC 220 Part Number 06540000 Motor to spindle Fill bore Accrolube with PTFE spline connection in spindle...
  • Page 99 The proprietary UV and Abrasion Resistant surface coating on SHIELDS SUPERCOATED polycarbonate significantly improves performance. Periodic cleaning using proper procedures and compatible cleaners are recommended to prolong service life. Tiger Corp. polycarbonate is SUPERCOATED on both sides. CLEANING THE SUPERCOAT HARD-COAT 1.
  • Page 100 MAINTENANCE RECOMMENDED FILLING INSTRUCTIONS FOR HYDRAULIC RESERVOIRS When filling or checking the oil level, the unit should be parked on a level surface., shut “OFF”, and allow sufficient time to cool to ambient temperature. Use caution when removing the pressurized breather.
  • Page 101 MAINTENANCE REPLACING HIGH PRESSURE HYDRAULIC FILTER ELEMENT Be certain that the system has been shut down and depressurized. Locate High Pressure Filter housing. Confirm that the new element to be installed matches the element p/n on the filter model tag. Example: V3.0510-06 (world line 100, HD049 model).
  • Page 102 MAINTENANCE GREASING THE SHEAVE Locate the grease zerk on the ends of the sheave pin. Inject Lithium-Complex Extreme Pressure grease conforming to NLGI2-ISO 320 specifications into the pin until it protrudes from the ends. This should be greased daily or for every 8 hours of service.
  • Page 103 MAINTENANCE GREASING DRAFT BEAM PIVOT POINTS Locate the grease zerks on the inner and outer draft beam pivot bosses. Inject Lithium-Complex extreme pressure grease, conforming to NLGI2- ISO 320 specifications, into each zerk until grease protrudes from joints. Grease all pivots daily or every 8 hours of service.
  • Page 104 MAINTENANCE DRIVE SHAFT YOKE, U-JOINT & STUB SHAFT With engine stopped, inject Lithium-Complex extreme pressure grease, conforming to NLGI2-ISO 320 specifications, into universal joints and slip yoke until grease appears at the seal. Grease them daily or every 8 hours. SIDE ROTARY Maintenance Section 4-16 ©...
  • Page 105 PUMP COUPLED TO MOTOR OR P.T.O.! Failure to do so will result in component failure! GREASING SPINDLE Locate grease fitting on inside of deck housing. Inject Tiger Spindle Lubricant, part number 06540000, into spindle housing. Fill with lubricant until lubricant weeps out of top spindle seal.
  • Page 106 For direct drive mowers, locate motor spline and spindle spline on the mower deck. Clean old grease from splines on motor shaft and in spindle. Fill bore in spindle with Accrolube with PTFE (Tiger #06520310). Use about 4 ounces of grease. Change grease yearly or every 500 hours.
  • Page 107 MAINTENANCE Blades Check the Blades for cracks and wear and Blade Bolts for tightness, daily. Blades should be replaced when they are worn excessively, bent, deformed, or out of balance. Blades should always be replaced in pairs. Blades of different weights can cause serious imbalance and damage to the machine and personnel.
  • Page 108 MAINTENANCE ROTARY KNIFE REPLACEMENT 1. Be sure you have a complete matching set of new knives for replacement. 2. Remove knives and inspect holes for damage. Also watch for cracks in the disk around the holes. 3. Lube threads with anti-seize, motor oil or grease. Install bolts through knife and disk from bottom side of disk.
  • Page 109 HEAVY DUTY SPINDLE ASSEMBLY INSTALLATION AND BEARING ADJUSTMENT A press MUST be used to install bearing cups, bearing cones, and seals. DO NOT use a hammer to install races, bearings, or seals. The parts of assembly may be damaged. NOTE: The grease zerk and gussets are located on the top side of the spindle housing. Be sure the spindle is assembled correctly.
  • Page 110 5. Turn the spindle housing over (up position) and fill with Tiger Spindle Lubricant (part number 06540000) to the top edge of the upper bearing cup.
  • Page 111 MAINTENANCE DAILY MAINTENANCE SCHEDULE The following services should be performed daily or every 8 hours of service, following the detailed maintenance instructions in the operator’s manual. _______ Pump Driveshaft: Check for end play in driveshaft / coupler and lubricate at zerks. _______ Crankshaft adapter: If equipped with rubber grommets check condition, replace if missing or damaged.
  • Page 112 MAINTENANCE SIDE ROTARY Maintenance Section 4-24 © 2017 Alamo Group Inc.
  • Page 113: Parts Section

    JD6M MY20 SIDE ROTARY w/ INDEPENDENT HYDRAULICS PARTS SECTION...
  • Page 114 2 SPOOL CABLE CONTROL MOUNT..............................10 BERM DRAFT BEAM TM..................................12 BERM DRAFT BEAM TSR..................................14 BERM DRAFT BEAM - HYDRAULICS..............................16 NOTES......................................... 17 COOLER MOUNT...................................... 18 NOTES 1........................................20 JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -2...
  • Page 115 PARTS ORDERING GUIDE JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -3...
  • Page 116 TRACTOR MOUNT KIT JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -4...
  • Page 117 CAPSCREW, 7/16 X 1 1/4,NC 21989 LOCKWASHER, 7/16" 21658 CAPSCREW, 7/16 X 2 ,NF 34848 HEX NUT, 7/16 06537071 SCREW,WING,1/4X5/8,NC,TYPE D,Z 6T2514 CAPSCREW,14MMX40MM(2.0 PITCH) 6T2624 LOCKWASHER,16MM 06530238 CAPSCREW, 3/4 X 6,NC,GR8 JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -5...
  • Page 118 ELBOW,1-1/2FOR X 1-1/2FOR,MACH 34626 CLAMP BRKT,62-6420 34710 ADAPTER,1 1/2ORB X 1 1/2MJ 34309 BALL VALVE,1 1/2 FOR 32382 BRACKET,HOSE 24849 SPACER 06505017 CLAMP KIT,HOSE,1X1.4,2PST 06520536 CLAMP,HOSE,2 1/2",INS 06510083 VALVE,BRAKE,SOL,3000PSI,METRI JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -6...
  • Page 119 ELBOW,12MJX12FJX,BT90 06412711 COVER,BV,06340079 06500746 HOSE,#24X107(24FJXX24FL45) 06501308 HOSE,#16X114(16FJXX20FL45) 06501309 HOSE,#16X93(16FJXX16FJX90L) 06501313 HOSE,#16X161(20FJXX16FJX90L) 06500953 HOSE,#12X35(12FJX90X12FJX) 06501259 HOSE,#12X205(12FJXX12FJX90) 06500753 HOSE,#16X103(16FJXX16MJ) 06501272 HOSE,#16X95(16FJXX20FL45) 33880 FLATWASHER 06530237 CAPSCREW, 3/4" X 2-1/4" NC JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -7...
  • Page 120 CABLE (MANUAL) LIFT VALVE 2 SPOOL JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -8...
  • Page 121 35111 HOSE,1/4" X 140" 06501259 HOSE,3/4" X 205" 06500953 HOSE,3/4" X 35" 06503218 ADAPTER, 3/4"MB X 3/4"MJ 06500311 HOSE, 1/4" X 156" 34025 HOSE, 1/4" X 152" JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -9...
  • Page 122 2 SPOOL CABLE CONTROL MOUNT JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -10...
  • Page 123 CAPSCREW, 3/8" X 2-1/4" NC 27082B SPACER 21627 NYLOCK NUT, 3/8" NC 06505100 108" CABLE CONTROL 6T3951 SCREW, MACHINE 8/32 X 1/2 06412358 BRACKET 06510045 COOLER FAN CONTROLLER JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -11...
  • Page 124 BERM DRAFT BEAM TM JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -12...
  • Page 125 21635 CAPSCREW,3/8X2 1/4,NC 21584 CAPSCREW, 5/16 X 2,NC 21577 HEX NUT,NYLOCK,5/16" NC 21627 NYLOCK NUT,3/8",NC 21986 LOCKWASHER, 1/4" 21530 CAPSCREW,1/4X1,NC,GR8 22014 FLATWASHER,1/4,GR8 21525 HEX NUT, 1/4" NC JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -13...
  • Page 126 BERM DRAFT BEAM TSR JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -14...
  • Page 127 21635 CAPSCREW,3/8X2 1/4,NC 21584 CAPSCREW, 5/16 X 2,NC 21577 HEX NUT,NYLOCK,5/16" NC 21627 NYLOCK NUT,3/8",NC 21986 LOCKWASHER, 1/4" 21530 CAPSCREW,1/4X1,NC,GR8 22014 FLATWASHER,1/4,GR8 21525 HEX NUT, 1/4" NC JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -15...
  • Page 128 CYLINDER,3X10,RTRY TOP PORT 34244 ELBOW, 1/2ORB X 1/2FOR 34396 ADAPTER,.06" REST,1/2" X 3/8" 6T4258 BREATHER,1/2 O-RING 06350019 DRAFT BEAM,BERM 06500848 HOSE,#4X46(6FJXX6FJX) 32909 HOSE,#4X36(6FJXX6FJX) 06500848 HOSE,#4X46(6FJXX6FJX) 33496 HOSE,#4X58(6FJXX6FJX) 06500311 HOSE,#4X156(6FJX90X6FJX) JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -16...
  • Page 129 NOTES JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -17...
  • Page 130 COOLER MOUNT JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -18...
  • Page 131 TANK SUPPORT (RE-USED FROM TRACTOR) ---- TRACTOR FUEL TANK (RE-USED FROM TRACTOR) WASHER (RE-USED FROM TRACTOR) ---- 3/4" FLANGE NUT (RE-USED FROM TRACTOR) 3/4" CAPSCREW (RE-USED FROM TRACTOR) JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -19...
  • Page 132 NOTES 1 JD6M MY20 SIDE ROTARY w IH ©2020 Alamo Group Inc. Parts Section -20...
  • Page 133 COMMON SIDE ROTARY PARTS SECTION...
  • Page 134 PART NAME INDEX PARTS ORDERING GUIDE ..................................3 60IN SIDE CABLE TM ROTARY MOWER............................... 4 72IN SIDE CABLE TM ROTARY MOWER............................... 6 60IN SIDE COMBO TM ROTARY MOWER .............................. 8 72IN SIDE COMBO TM ROTARY MOWER ............................10 60IN SIDE TM CHAIN GUARDS................................12 72IN SIDE TM CHAIN GUARDS................................
  • Page 135 PARTS ORDERING GUIDE COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-3...
  • Page 136 60IN SIDE CABLE TM ROTARY MOWER COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-4...
  • Page 137 60IN SIDE CABLE TM ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 32099 RTRY, 60" DECK, CABLE 31773 GAURD,CHAIN,FRONT,SR60 6T1001 BRKT, MOTOR MTG, 60"SIDE RTRY 6T0820H SKID SHOE, TM60 22592 FLAP, DEFLECTOR, TM60 6T0823 BAR, FLAP, TM60 6T1024H5 SPINDLE ASSY,CPLT,HD,5/8" HOLES 21223 SPROCKET, 1-1/4"...
  • Page 138 72IN SIDE CABLE TM ROTARY MOWER COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-6...
  • Page 139 72IN SIDE CABLE TM ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 21225B RTRY,72" DECK, CABLE 31931 GUARD,CHAIN,FRONT,SR72 6T1001 BRKT, MOTOR MTG, 60"SIDE RTRY 21248 SKID SHOE, TM72 21295B FLAP, DEFLECTOR, TM72 21242A BAR, FLAP, TM72 6T1024H5 SPINDLE ASSY,CPLT,HD,5/8" HOLES 21223 SPROCKET, 1-1/4"...
  • Page 140 60IN SIDE COMBO TM ROTARY MOWER COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-8...
  • Page 141 60IN SIDE COMBO TM ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 30087D RTRY, 60" DECK, COMBO - STD DUTY 32617 RTRY, 60” DECK, COMBO - HEAVY DUTY 31773 GUARD,CHAIN,FRONT,SR60 6T1001 BRKT, MOTOR MTG, 60"SIDE RTRY 6T0820H SKID SHOE, TM60 22592 FLAP, DEFLECTOR, TM60 6T0823...
  • Page 142 72IN SIDE COMBO TM ROTARY MOWER COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-10...
  • Page 143 72IN SIDE COMBO TM ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 34260 RTRY, 72" DECK, COMBO - STD DUTY 31408A RTRY, 72” DECK, COMBO - HEAVY DUTY 31931 GUARD,CHAIN,FRONT,SR72 6T1001 BRKT, MOTOR MTG, 60"SIDE RTRY 21248 SKID SHOE, TM72 21295B FLAP, DEFLECTOR, TM72 21242A...
  • Page 144 60IN SIDE TM CHAIN GUARDS COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-12...
  • Page 145 60IN SIDE TM CHAIN GUARDS Continued... ITEM PART NO. QTY. DESCRIPTION 31773 GUARD,CHAIN,TM60,FRONT,ASSY 31762 GUARD,CHAIN,TM60,FRONT 28407 CABLE,5/16",BULK (QTY IN FEET) 22993 CHAIN,5/16",GR30,9 LINK 28408 U-BOLT,CABLE,5/16" (NOT SHOWN) 31774 GUARD,CHAIN,TM60,REAR,ASSY 31763 GUARD,CHAIN,TM60,REAR 31879 ROD,SHORT,TM60 31878 ROD,LONG,TM60 22016 FLATWASHER,3/8",GR8 6T3028 COTTER PIN,1/8" X 1" 22992 CHAIN,5/16",GR30,10 LINK COMMON SIDE ROTARY...
  • Page 146 72IN SIDE TM CHAIN GUARDS COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-14...
  • Page 147 72IN SIDE TM CHAIN GUARDS Continued... ITEM PART NO. QTY. DESCRIPTION 31931 GUARD,CHAIN,TM72,FRONT,ASSY 31863 GUARD,CHAIN,TM72,FRONT 28407 CABLE,5/16",BULK (QTY IN FEET) 22993 CHAIN,5/16",GR30,9 LINK 28408 U-BOLT,CABLE,5/16" (NOT SHOWN) 31932 GUARD,CHAIN,TM60,REAR,ASSY 31864 GUARD,CHAIN,TM60,REAR 31934 ROD,LONG,TM72 31933 ROD,SHORT,TM72 22016 FLATWASHER,3/8",GR8 6T3028 COTTER PIN,1/8" X 1" 22992 CHAIN,5/16",GR30,10 LINK COMMON SIDE ROTARY...
  • Page 148 60IN SIDE TSR ROTARY MOWER COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-16...
  • Page 149 60IN SIDE TSR ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 34975 HEAVY DUTY GRASSKAT COMBO ------ 06320005 STD DUTY GRASSKAT COMBO ------- 06320008 HEAVY DUTY GRASSKAT CABLE 34980 SPINDLE ASSY,TM 60" 06504016 CURRENT MOTOR,(M365-1 1/4" 14-SPLINE) 06410254 SKID,OUTBOARD,TM60 22992 CHAIN,10 LINK 6T2270 PLOW BOLT,3/8"...
  • Page 150 60IN SIDE TSR REAR GUARDS COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-18...
  • Page 151 60IN SIDE TSR REAR GUARDS Continued... ITEM PART NO. QTY. DESCRIPTION 34973 ROD,CHAIN,OUTER,TM60 34974 ROD,CHAIN,INNER,TM60 21631 CAPSCREW, 3/8 X 1-1/4,NC 34972 PLATE,CAP,CHAIN 21625 HEX NUT,3/8",NC 21988 LOCKWASHER, 3/8" 22992 CHAIN,10 LINK 06410947 MNT,FLAP,RH,EXT,TSR 06401184 STRAP,FLAP,EXT,TSR 06410948 COVER,FLAP,EXT,TSR 21632 CAPSCREW,3/8" X 1-1/2" NC 22016 FLATWASHER,3/8",GR8 06410946...
  • Page 152 SIDE ROTARY CASTER WHEEL ASSEMBLY COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-20...
  • Page 153 SIDE ROTARY CASTER WHEEL ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 25214C FRAME,CASTER,WHL (TM60) 28297A FRAME,CASTER WHL (TM72) 22057 SPINDLE,CASTER AXLE,ASSY 6T2617 BUSHING,MACH,1-1/2IDX 2-1/4OD 28548 CASTER WHEEL,SOLID TIRE 22065 HUB,ASSY,CASTER ---- 22066 HUB,CASTER 22070 DUST CAP ---- 22071 HUB STUD 22073 HEX NUT,1”,NF (SLOTTED) ----...
  • Page 154 CASTER WHEEL ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 22057 SPINDLE,CASTER AXLE,ASSY 21987 LOCKWASHER,5/16” 21575 HEX NUT,5/16” 28548 CAPSCREW,5/16” X 3/4”,NC 22697 RIM,OUTER,CASTER ASSY 21416 TIRE,SOLID 22696 RIM,CASTER WHEEL 22070 DUST CAP 22533 COTTER PIN,3/16” X 2” 6T0836 CUP,CASTER WHEEL 22073 HEX NUT,1",NF (SLOTTED JAM NUT) 22071 HUB STUD...
  • Page 155 ROTARY DISK AND KNIVES ITEM PART NO. QTY. DESCRIPTION 34876 BLADE MOUNTING DISK 6T1023R NYLOCK NUT,1-1/8” 34878 SPACER 34497 KNIFE MOUNTING BOLT 34685 KNIFE,60" HIGH SUCTION - STANDARD 34684 KNIFE,60" - OPTIONAL 34682 KNIFE 72” (MOUNT ON 72” MOWER ONLY) 25270 FLATWASHER,5/8",USS,GR8 6T2259...
  • Page 156 TM MOWER SPINDLE ASSEMBLY COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-24...
  • Page 157 TM MOWER SPINDLE ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION ------ 6T1024H5 SPINDLE ASSEMBLY COMPLETE 6T1031 SPROCKET 6T1016 BEARING LOCK NUT - THICK 22596 JAM WASHER 6T1015 BEARING ADJUSTMENT NUT - THIN 6T1014 BEARING ADJUSTMENT SLEEVE 6T1011 UPPER SEAL - SET OF 2 6T1012 BEARING CONE 6T1013...
  • Page 158 TSR MOWER SPINDLE ASSEMBLY COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-26...
  • Page 159 TSR MOWER SPINDLE ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION ------ 34980 SPINDLE ASSEMBLY COMPLETE 34978 SPINDLE MOUNT 34979 SPINDLE,TM60 6T1013 BEARING CUP 6T1012 BEARING CONE 6T1011 UPPER SEAL - SET OF 2 6T1014 BEARING ADJUSTMENT SLEEVE 6T1013H BEARING,CUP,HD 6T1012H BEARING CONE,HD 6T1011H SEAL,LOWER,HD...
  • Page 160 ROTARY MOTOR BREAKDOWN COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-28...
  • Page 161 ROTARY MOTOR BREAKDOWN Continued... ITEM PART NO. QTY. DESCRIPTION 06504011 MOTOR ASSEMBLY 22790 END,COVER 06504088 HOUSING, PEC 06504111 HOUSING, GEAR 06504026 SET, GEAR SHAFT 06504104 CAPSCREW 06504078 SCREW, DRIVE 06504092 06504093 PIN, DOWEL 06504094 NAME PLATE 06504095 THRPL 2961940 PLUG, ODT 2962200 RING, SNAP 06504096...
  • Page 162 60IN TSR ROTARY MOTOR BREAKDOWN COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-30...
  • Page 163 60IN TSR ROTARY MOTOR BREAKDOWN Continued... ITEM PART NO. QTY. DESCRIPTION 06504016 MOTOR(M365-1 1/4SPLINE),SEALED 22790 COVER,END 06504088 HOUSING,PEC 06504111 HOUSING,GEAR 06504110 SET,GEAR SHAFT 06504104 CAP SCREW 06504078 SCREW,DRIVE 06504093 PIN,DOWEL 06504094 NAME PLATE 06504095 THRPL 02961940 PLUG,ODT (0.25) 6T5200 RING,SNAP 06504097 SEAL,LIP 22797...
  • Page 164 FRONT HYDRAULIC PUMP BREAKDOWN COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-32...
  • Page 165 FRONT HYDRAULIC PUMP BREAKDOWN Continued... ITEM PART NO. QTY. DESCRIPTION 23152 PUMP ASSEMBLY,1-3/4”,COMPLETE 22766 SHAFT END COVER 22779 PORT END COVER 22774 GEAR HOUSING,1-3/4” 22771 GEAR SET 23824 CAPSCREW 06504078 SCREW,DRIVE 22773 DOWEL PINS 06504077 NAMEPLATE 22770 THRUST PLATE 22767 PLUG 06504075 SEAL,BK-UP...
  • Page 166 PUMP AND GRILL GUARD OPTIONS ITEM PART NO. QTY. DESCRIPTION 32430 UNIVERSAL PUMP GUARD 32737 UNIVERSAL GRILL GUARD 21833 CAPSCREW,3/4" X 2-1/4",NC 22021 FLATWASHER,3/4" 21993 LOCKWASHER,3/4" 21825 HEX NUT,3/4",NC COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-34...
  • Page 167 RESERVOIR TANK FILTER ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 06505044 FILTER ASSY SAE 10 MICRON 28583 CAPSCREW,8MM X 25MM(1.25 PITCH) 06505045 COVER 06505046 SEAL KIT 06505047 SPRING 06505048 BYPASS 35259 FILTER,10 MIC,RETURN LINE 06505049 CAN/BODY COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-35...
  • Page 168 3IN X 10IN HYDRAULIC CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION ------ 6T0151R HYD. CYLINDER 3" X 10" 6T0167 CYLINDER BUTT 6T0170 CYLINDER GLAND 6T0178 CLEVIS END 6T0164 CYLINDER TUBE 6T0161 PISTON ROD 6T0173 PISTON 6T0179 LOCKNUT 6T0176 TIE ROD ASY ------ 6T0187 SEAL KIT...
  • Page 169 3IN X 12IN HYDRAULIC CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION ------ 32215 HYD. CYLINDER 3" X 12" (STD DUTY) 25343 HYD. CYLINDER 3" X 12" (HVY DUTY) 6T0167 CYLINDER BUTT 6T0170 CYLINDER GLAND 6T0178 CLEVIS END 6T0204 CYLINDER TUBE 6T0203 PISTON ROD 6T0173...
  • Page 170 3IN X 18IN HYDRAULIC CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION ------ 6T0150 CYLINDER 3" X 18" 6T0167 CYLINDER BUTT 6T0170 CYLINDER GLAND 6T0178 CLEVIS END 6T0165 CYLINDER TUBE 6T0162 PISTON ROD 6T0173 PISTON 6T0179 LOCKNUT 6T0177 TIE ROD ASY ------ 6T0187 SEAL KIT...
  • Page 171 CABLE (MANUAL) LIFT VALVE BREAKDOWN - 30801 COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-39...
  • Page 172 CABLE (MANUAL) LIFT VALVE BREAKDOWN - 30801 Continued... ITEM PART NO. QTY. DESCRIPTION TB1017S INLET END COVER TB1702 END COVER, POWER BEYOND TB1017P VALVE SECTION (SINGLE ACTING, SPRING DETENT) 06502091 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) (NO AUX VALVE PORTS) TB1017M SHUT-OFF PLUG TB1017E...
  • Page 173 CABLE (MANUAL) LIFT VALVE BREAKDOWN - 31320 COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-41...
  • Page 174 CABLE (MANUAL) LIFT VALVE BREAKDOWN - 31320 Continued... ITEM PART NO. QTY. DESCRIPTION 31595 INLET END COVER 31594 END COVER, LOAD SENSE 31597 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 31597 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 06503067 RELIEF PLUG 06503067 RELIEF PLUG 6T4209 RELIEF PLUG...
  • Page 175 CABLE (MANUAL) LIFT VALVE BREAKDOWN - 31321 COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-43...
  • Page 176 CABLE (MANUAL) LIFT VALVE BREAKDOWN - 31321 Continued... ITEM PART NO. QTY. DESCRIPTION 31595 INLET END COVER 31594 END COVER, LOAD SENSE 31597 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 31597 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 06503067 RELIEF PLUG 31861 RELIEF VALVE, 360 PSI 6T4209 RELIEF PLUG...
  • Page 177 CABLE (MANUAL) LIFT VALVE BREAKDOWN - 31752 COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-45...
  • Page 178 CABLE (MANUAL) LIFT VALVE BREAKDOWN - 31752 Continued... ITEM PART NO. QTY. DESCRIPTION TB1017S INLET END COVER TB1702 END COVER, POWER BEYOND TB1017P VALVE SECTION (SINGLE ACTING, SPRING DETENT) TB1017P VALVE SECTION (SINGLE ACTING, SPRING DETENT) TB1017M SHUT-OFF PLUG TB1017E RELIEF VALVE, 2250 PSI TB1017M SHUT-OFF PLUG...
  • Page 179 CABLE (MANUAL) LIFT VALVE BREAKDOWN - 06502040 COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-47...
  • Page 180 CABLE (MANUAL) LIFT VALVE BREAKDOWN - 06502040 Continued... ITEM PART NO. QTY. DESCRIPTION 31595 INLET END COVER 31594 END COVER, LOAD SENSE 31597 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 31597 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) (REMOVE SHUTTLE DISC) 06503067 RELIEF PLUG 06503067 RELIEF PLUG...
  • Page 181 CABLE (MANUAL) LIFT VALVE BREAKDOWN - 06502041 COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-49...
  • Page 182 CABLE (MANUAL) LIFT VALVE BREAKDOWN - 06502041 Continued... ITEM PART NO. QTY. DESCRIPTION 31595 INLET END COVER 31594 END COVER, LOAD SENSE 31597 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 31597 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 06503067 RELIEF PLUG 31861 RELIEF VALVE, 360 PSI 06503068 RELIEF PLUG...
  • Page 183 BRAKE VALVE ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 06510083 BRAKE VALVE, ASSY 34092 BRAKE VALVE, BLANK 34094 LOGIC ELEMENT 34095 RELIEF VALVE, 3000 PSI 06510095 METRI PAK COIL 34093 CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT & WASHER) 34091 RELIEF VALVE, 2600 PSI 34096 RELIEF SEAL KIT ----...
  • Page 184 BRAKE VALVE HYDRAULIC SCHEMATIC COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-52...
  • Page 185 SWITCH BOX ITEM PART NO. QTY. DESCRIPTION 06514013 SWBX,ALUM,BLK,06510102 35226 SWITCH,MOWER,COLEHERSEE 33811 SWITCH,MASTER/DECK FLOAT 6T3923 INDICTATOR LIGHT,ON,RED 06514014 BREAKER,10A,SWBX 34540 STRAIN RELIEF,3/4,BLACK,NYLON 06550018 DECAL,SWTCHBX,TM/TSF,CG 35227 RELAY,DP,DT,12V,LY2F,35226 COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-53...
  • Page 186 SWITCH BOX SCHEMATIC COMMON SIDE ROTARY ©2020 Alamo Group Inc. Parts Section 6-54...
  • Page 187 WARRANTY SECTION Warranty Section 7-1...
  • Page 189: Warranty Information

    All Tiger obligation under this warranty shall be terminated if the equipment is modified or altered in ways not approved in writing by Tiger, if repair parts other than genuine Tiger repair parts have been used, or if the equipment has been subject to misuse, neglect, accident, improper maintenance or improper operation.
  • Page 190 . Common sense should play a large role in the operation of this machine. Since we at Tiger Corporation are constantly striving to improve out products, we reserve the right to change specifications or design at any time.
  • Page 191 TO THE OWNER / OPERATOR / DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this manual and on the machine. The table of contents clearly identifies each section where you can easily find the information you need. The Occupational Safety and Health Act (OSHA 1928.51 subpart C) makes the following minimum requirements for tractor operators.
  • Page 192 Printed in USA © Tiger Corporation...