Table of Contents
Advertisement
E2J70BD_EN.book Page 42 Friday, June 29, 2007 2:50 PM
PDC (Programme Delivery Control)
Programme Delivery Control (PDC) assures that the
TV programmes you have programmed for timer
recording are recorded exactly from beginning to end,
even if the actual broadcasting time differs from the
scheduled time due to a delayed start or extension of
the programme duration. Furthermore, if a
programme is interrupted, the recording will also be
interrupted automatically and resumed when the
programme starts again.
If the PDC signal drops out because the broadcast
signal is weak, or if a broadcasting station does not
transmit a regular PDC signal, the timer recording is
performed in normal mode (without PDC) even if it
was programmed for PDC. If the starting time of the
PDC timer recording is between 0:00 and 3:59 on a
given day, the PDC function will operate from 20:00
on the previous day to 4:00 on the next day. If the
starting time of the PDC timer recording is between
4:00 and 23:59 on a given day, the PDC function will
operate from 0:00 on the given day to 4:00 on the next
day. This means that if the relevant programme is
broadcasted within this period, it is recorded correctly.
If the timer is not programmed correctly, the incorrect
timer setting stays in effect unless you cancel it. To
cancel an incorrect timer setting, refer to "Checking,
Cancelling or Correcting the Timer Programming
Information" below.
Note
• This feature is only available for analogue channels.
Checking, Cancelling or Correcting
the Timer Programming Information
1
Press [TIMER PROG.].
Timer Programming list will appear.
2
A) To delete the timer programme:
1) Select the programme you want to delete using
[U \ D], then press [ENTER/OK].
2) Select "Delete" using [U \ D], then press
[ENTER/OK].
Confirmation window will appear.
3) Select "Yes" using [U \ D], then press
[ENTER/OK].
B) To correct the timer programme:
1) Select the programme you want to correct
using [U \ D], then press [ENTER/OK].
2) Select "Program Change" using [U \ D], then
press [ENTER/OK].
3) Correct the timer programme by using
[U \ D \ L \ P], then press [ENTER/OK].
3
Press [TIMER PROG.] to exit.
To check the timer programming in process
Press [TIMER PROG.].
42
EN
Skip the Periodical Timer Recording
You can deactivate the periodical (Daily, Mon-Fri or
Weekly) timer recording temporarily.
1
In stop mode, press [TIMER PROG.].
2
Select the periodical timer recording
programme you want to skip using
[U \ D], then press [ENTER/OK].
3
Select "Program Change" using
[U \ D], then press [ENTER/OK].
4
Move the cursor to the "Skip" field
using [L \ P], then select "ON" using
[U \ D] and then press [ENTER/OK]
to activate the setting.
• "✔" will be displayed on the left side of the timer
programme.
• The setting will go back to "OFF" after the
programme is skipped once.
To Stop the Timer Recording in
Progress
On the front panel of the unit, press
[C STOP] to stop the recording, or press
and hold [STOP C] on the remote control
for 2 seconds.
• You can also stop the timer recording in progress by
deleting the timer programme. Press
[TIMER PROG.] while the timer recording is in
progress, then follow A) in step
Cancelling or Correcting the Timer Programming
Information" on this page.
If the Timer Programming Did Not
Complete Correctly
The error number appears on the Timer Programming
list.
Timer Programming
Date
Start
End
E40
06/12
7:00
9:00
New Program
The error programme will be displayed in gray
with an error number.
2)
of the "Checking,
0:00 THU 06/12
STTL
CH
PDC
901
1/1
Advertisement
Table of Contents
