Subscribe to Our Youtube Channel
Related Manuals for APV GRASSLAND PRO HARROW GP 600 M2
Summary of Contents for APV GRASSLAND PRO HARROW GP 600 M2
- Page 1 GRASSLAND PRO HARROW GP 600 M2 OPERATING MANUAL PLEASE READ CAREFULLY BEFORE INITIAL OPERATION Translation of the original operating manual Version: 2.3 en-US; item number: 00602-3-776...
-
Page 2: Table Of Contents
TABLE OF CONTENTS EC DECLARATION OF CONFORMITY ..................4 UK CONFORMITY ASSESSED ...................... 5 IDENTIFICATION OF THE DEVICE ....................6 SERVICE ............................6 WARRANTY ........................... 7 Warranty activation ......................7 SAFETY INSTRUCTIONS ......................7 Intended use ........................7 General safety information and accident prevention regulations .......... 8 Attached implements ...................... - Page 3 ASSISTANCE FOR FAULTS ......................28 Procedure for faults or errors ..................... 28 MAINTENANCE AND CARE ......................28 10.1 General maintenance instructions ..................28 10.2 Instructions for regular maintenance .................. 28 10.3 Replacing the tines ......................29 10.4 Tine safety/ ........................29 10.5 Lubrication schedule ......................
-
Page 4: Ec Declaration Of Conformity
If the implement is modified without prior consultation with APV Technische Produkte this declaration shall lose its validity. -
Page 5: Conformity Assessed
If the implement is modified without prior consultation with APV Technische Produkte this declaration shall lose its validity. -
Page 6: Identification Of The Device
If, despite of the information in this operating manual, you have questions concerning the handling of this device For questions regarding spare parts To commission service and maintenance tasks Service address: APV Technische Produkte GmbH Telephone: +43 2913 8001-5500 Zentrale: Dallein 15 Fax: +43 2913 8002 3753 Hötzelsdorf E-mail: service@apv.at AUSTRIA... -
Page 7: Warranty
WARRANTY ACTIVATION Every APV implement must be registered immediately after delivery. The registration activates the claim for warranty performances and thus APV can guarantee the best service. To activate the warranty for your implement, simply scan the QR code with your smartphone –... -
Page 8: General Safety Information And Accident Prevention Regulations
GENERAL SAFETY INFORMATION AND ACCIDENT PREVENTION REGULATIONS The warning and information signs affixed on the implement provide important instructions for safe operation. Do not remove the warning and information signs under any circumstances. Comply with the warning and information signs for your own safety! ... - Page 9 Do not transport work materials on the implement; the exception is seed in the hopper of a Pneumatic Seeder that may be attached. Accessories must be properly mounted in compliance with standards by qualified specialists from an appropriately authorized company. ...
-
Page 10: Attached Implements
ATTACHED IMPLEMENTS Only APV machines and accessories may be mounted on the implement. Do not step between the tractor and implement when activating the external control operating unit for the three-point attachment! ... -
Page 11: Maintenance
Components that cannot be removed with tools, such as a screwdriver or wrench, may only be replaced by qualified specialists from an appropriately authorised company or by APV Customer Service. The operator/user must check the implement (each time before use) for any fractures and cracks, leaks, abrasion points, loose bolts or connections, vibration, and correct function. -
Page 12: Load Index And Speed Index
The platform kit must only be used as a maintenance walkway. A ladder must be made that is in conformance with standards. This ladder is available from APV. When not in use, the steps must be swung upward and secured. -
Page 13: Danger Areas In Implement Operation
CAUTION! Risk of impact and crushing due to moving implement parts Moving implement parts pose a risk of injuries due to impact or crushing. The danger area includes the area across the entire width of the implement (see Figure 3). Maintain an additional safety distance of 2 m from the implement. -
Page 14: Danger Areas When Folding And Unfolding
6.8.2 DANGER AREAS WHEN FOLDING AND UNFOLDING Figure 4 RESIDUAL HAZARDS Residual hazards are special hazards when working with the implement that cannot be eliminated despite safety-compliant design. Residual hazards are often not obvious and can be a source of possible injuries or health risks. 6.9.1 DANGER ARISING FROM MECHANICAL SYSTEMS There is a risk of accidents due to crushing, cutting, and impact on body parts... -
Page 15: Dangers Arising From Operation
6.9.3 DANGERS ARISING FROM OPERATION In operation, there is a risk of injury to body parts, particularly the face, due to rocks and clods of soil being flung upwards. INFORMATION SIGNS / HAZARD LABELS Pay attention to the stickers on the implement; they warn of particular hazards! CAUTION! Keep information signs and hazard labels clean If information signs and/or hazard labels become loose or are already detached, they must be replaced... - Page 16 Information sign (symbolic representation) Order number 00603-3-687 00600-3-138 00600-3-163 Retighten all bolts and These stickers indicate Labelling of the lubrication Explanation nuts after brief use. the tire pressure. points. Information sign Order number 00602-3-119 00600-3-139 00601-3-658 Loading hook. Fasten the Retighten the wheel nuts / Label for the recess for cable or chains here...
-
Page 17: Hazard Labels
HAZARD LABELS Information sign Order number 00604-3-648 00603-3-664 00602-3-294 Caution, crushing area! Attention – do not climb Never reach into the Always lift the implement Explanation onto the implement! crush hazard zone as slowly off the ground. long as parts are moving Rollover hazard! in this zone! Information... -
Page 18: Placement Of The Hazard Labels And Other Markings
PLACEMENT OF THE HAZARD LABELS AND OTHER MARKINGS The figures below show the arrangement of the hazard labels and other markings. Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10... -
Page 19: Operating Manual
Figure 11 Figure 12 OPERATING MANUAL STRUCTURE AND MODE OF OPERATION Drawbar Folding cylinders Chassis cylinder running gear levelling plate Tines, 12 mm Tines, 8 mm Roller cylinder Cambridge roller / toothed ring roller Figure 13 Thanks to its robust and compact design, the Grassland Pro harrow is ideal for new seeding, reseeding, and controlling weeds on grassland. -
Page 20: Attachment And Detachment Of The Implement
ATTACHMENT AND DETACHMENT OF THE IMPLEMENT 8.2.1 GENERAL INSTRUCTIONS The tractor tire pressure must be selected as specified by the tractor manufacturer. Additional wheel weights can be advantageous for difficult operating conditions. Comply with the information provided by the tractor manufacturer. ... -
Page 21: Uncoupling
CAUTION! Only connect the hydraulic hoses when the hydraulic system on the towing vehicle and the implement are depressurized. The lighting and electrical cables (if present) must be connected. The lighting function must be tested. Hydraulic connections for roller (yellow dust caps) Hydraulic connections for chassis (blue dust caps) -
Page 22: Unfolding From Transport Position To Work Position
CAUTION! Always secure the implement to prevent it from rolling. CAUTION! Prior to uncoupling, you must check again to ensure that the mechanical folding lock is locked in place. CAUTION! Comply with the sequence for locking the pneumatic brake system ! First uncouple the red brake line, then uncouple the yellow brake line. -
Page 23: Folding From Work Position Into Transport Position
FOLDING FROM WORK POSITION INTO TRANSPORT POSITION The hydraulic cylinders for depth adjustment of the rollers must be in the maximum possible retracted position. When using the 410 mm toothed ring roller the total length of the clips that are used on the roller cylinders must not exceed 100 mm. -
Page 24: Adjusting The Series Of Holes
8.5.2 ADJUSTING THE SERIES OF HOLES In addition to depth adjustment, the aggressiveness of each individual tine row can also be changed individually. This makes it possible to compensate for the different levels of wear of the individual tines. For series of holes adjustment, the pins of the tine sections are inserted either in a higher / more forward or deeper / more rear-ward hole (see Figure 23). -
Page 25: Coupling And Uncoupling The Roller
1 Crank 2 Locking pins 3 Shear bolt 4 Levelling plate Figure 24 Figure 25 Figure 26 CAUTION! Only operate the crank with one hand; two-hand operation poses a considerable risk of injury (hand or finger injuries). The crank has a slip safeguard for better handling and transmission of force. -
Page 26: Folding Lock
NOTE! Note that by removing the rollers, uniform depth guidance may no longer be ensured. For this reason, after dismounting, the rollers must always be replaced by feeler wheels. CAUTION! Only mount or dismount the rollers using the mounting kit for feeler wheels (see point 18.9). Figure 28 Figure 27 Figure 29... -
Page 27: Turning On The Headland
CAUTION! For every folding procedure of the side frames, the operator must visually inspect the folding lock. Road transport of the implement is only permitted if the folding lock is locked in position. TIP! For easier release of the folding lock, briefly charge the folding cylinder with pressure. This fully extends the folding cylinder and the side frame is again completely lifted. -
Page 28: Assistance For Faults
Use environmentally-friendly agents to protect the implement from corrosion during the winter. We expressly state that parts and accessories that are not delivered by APV are neither tested nor are they approved by APV. Consequently, installing and/or using such products can negatively alter or affect the prescribed design characteristics of your implement. -
Page 29: Replacing The Tines
Check the hydraulic hoses for wear, damage, and ageing before every start-up. Damaged or faulty parts must be replaced immediately. The wheel nuts must be checked every 50 km and retightened if necessary. The tightening torque of the wheel nuts is specified in the table below. ... - Page 30 Quantity Position Bearing on the lower link rod, lateral slope compensation (Figure 35) Bolt, pivot point when cornering (Figure 35) Bearing of the side frames (2 lubrication points per frame, Figure 36) Bolt and pivot point of the folding cylinder (3 lubrication points per folding cylinder; Figure 37 no.
-
Page 31: Repair And Corrective Maintenance
Figure 39 Figure 40 Figure 41 Figure 42 10.6 REPAIR AND CORRECTIVE MAINTENANCE Contact the manufacturer if the implement fails or is damaged. The contact data is provided in chapter 3. INFORMATION ON NATURE CONSERVATION AND ENVIRONMENTAL PROTECTION Energy-efficient use The tines of the implement should not penetrate into the field any deeper than necessary. -
Page 32: Technical Data
TECHNICAL DATA type designation GP 600 M2 Working width Transport dimensions 3.50 x 2.99 x 5.75 (folded) in m (HxWxD) Weight (toothed ring roller 4,800 kg 410 mm and PS 500 H) Tires (transport wheels) 500/50-17“ 2 rows with 12 mm tines (red) 3 rows with 12 mm 4 rows with 8 mm... -
Page 33: Possible Combinations With A Pneumatic Seeder
POSSIBLE COMBINATIONS WITH A PNEUMATIC SEEDER PS200 H PS300 H PS500 H PS800 H Dimensions HxWxD GP weight Dimensions HxWxD [cm] [kg] [cm] Delivery Road transport Without 127x105x17 100x70x110 110x77x150 117x80x125 Without With and without PS 500 GP 600 toothed 350 x 299 x 575 ~ 4700 Can be combined with mounting kit for PS... - Page 34 Do not allow the implement to cover the tractor unit's lighting equipment; if it does the lighting equipment must be installed on the implement. Do not allow the implement to impair or reduce the tractor's steerability! To achieve transport position, i.e. the necessary width for road transport, the side parts as well as the rollers must be completely folded.
-
Page 35: Lighting Circuit Diagram
LIGHTING CIRCUIT DIAGRAM Legend: Right Connector, 12 V, 7- Right tail light Turn signal Tail light Brake light Left Left tail light Brake light Tail light Turn signal Connector and cable pin assignment Color Function Yellow Left turn signal Figure 43 54 g White Ground... -
Page 36: Disposal
16.3 DISPOSAL The implement and the required working materials (working materials such as hydraulic oil) must be disposed of in accordance with local waste disposal regulations for machines. CROP CULTIVATION TIPS FOR USE OF THE GRASSLAND PRO HARROW Seedbed preparation is always required before reseeding. This procedure is optimally accomplished with the Grassland Pro Harrow with 4 tine rows. -
Page 37: Accessories
ACCESSORIES 18.1 EQUIPMENT KIT FOR OPERATION ON PUBLIC TRAFFIC AREAS This kit is required for compliance with all regulations for operation on public traffic areas. The kit consists of the following components: Dual-circuit pneumatic brake system Wheel chocks ... - Page 38 Note that with a vented trailer brake valve, the service brake is not active; thus the forward speed imposed by the country-specific regulations for unbraked, towed agricultural machinery, must be complied with. 18.1.1.1 DRAINING A drain valve is provided on the underside of the reservoir. The drain valve must be activated weekly throughout the year and daily in the winter.
-
Page 39: Wheel Chocks
18.1.1.4 PNEUMATIC BRAKE SYSTEM DIAGRAM The diagram of the dual-circuit pneumatic brake system is shown below: 1 Connection coupling 2 Trailer brake valve 3 Reservoir 20 l 4 Test connection 5 Drain valve 6 Test connection 7 Diaphragm cylinder Figure 50 18.1.2 WHEEL CHOCKS The wheel chocks prevent the implement from rolling. -
Page 40: Mudguard
18.1.5 MUDGUARD The mudguards are also available separately under the following order number: Order number: Tire dimensions 500/50-17": 06028-2-247 Tire dimensions 400/60-15.5" and 12.5" / 80-18": 06028-2-216 Figure 54: Symbolic image 18.1.6 ANTI-THEFT DEVICE The anti-theft device is also available separately under the following order number: Order number: 06028-2-262 18.2 MOUNTING KIT FOR PS 200 TO PS 500... -
Page 41: Platform Kit
18.5 PLATFORM KIT A suitable platform kit is available as an accessory for easier maintenance of the PS 200 to PS 800 Pneumatic Seeder. Please note that it must be mounted in compliance with the standards. Order number: 06028-2-275 Figure 58 18.6 CHANGEOVER VALVE FOR OPERATING TWO HYDRAULIC FUNCTIONS With the changeover valve it is possible to interconnect... -
Page 42: Mounting Kit For Feeler Wheels
TIP! Before driving off for the first time, calibrate the speed on the Control Box 5.2. Figure 61 18.9 MOUNTING KIT FOR FEELER WHEELS This kit is necessary if you want to mount or dismount the roller of the GP. It consists of ... -
Page 43: Spare Parts
Please have your product number / serial number on hand. You can also access our online spare parts catalog on our website www.apv.at the Service area. For questions concerning spare parts or your order, our customer service organization (see point 4 Service for contact data) would likewise be happy to assist you. - Page 44 APV – Technische Produkte GmbH Headquarters: Dallein 15 3753 Hötzelsdorf, Austria Tel.: +43 2913 8001 office@apv.at www.apv.at...
Need help?
Do you have a question about the GRASSLAND PRO HARROW GP 600 M2 and is the answer not in the manual?
Questions and answers