MikroTik RouterBOARD Groove 5Hn Quick Setup Manual And Warranty Information

Route R rBOA
Qu uick Setu up Guide
The e RouterBOAR RD Groove 5H
802 2.11a/n wirele ess, an N‐Mal
sup pports MDI‐X auto detectio
two o mounting lo oops.
Fi irst use
1. Connec ct the antenna
2. Twist to o open the Gr
3. Use the e provided rub
opening g, so that the
4. The Gro oove accepts
5. The def fault IP addre
Userna me is admin a
Po owering
The e board accep pts powering f
 Ethe ernet port acc
ada pter and a Po
Ma ximum power r consumption
Bo ooting pr rocess
Thi is device does sn't come fitte
the e Ethernet cab ble, using the
def fault IP addre ss of 192.168
In c case IP conne ction is not av
info ormation here e: http://wiki
In c case you wish h to boot the d
dev vice when sta rting it until t
M ounting
If y you wish to tig ghten the Gro
two o mounting lo oops ‐ guide th
wil l be mounted d. You should a
po le, so that the e cable weight
Gro oove device. T This is to ensu
Ex xpansion n Slots an

Built in 5G GHz 802.11a/

One 10/1 100 Ethernet
straight o or cross-over
from a pa assive PoE inje
See e www.routerbo oard.com for mo
ARD G Groov
and War rranty In
Hn comes prei nstalled in an
e antenna co nnector, and
on. The device e is packaged w
a to the N‐Ma le connector
roove case, co onnect an Ethe
bber insulator r to put on the
opening is tig ghtly closed
8‐30V Passive e PoE from a P
ss from Ether 1 is 192.168.8
and there is n o password
from the Ether rnet port (Pas
cepts passive Power over
E injector.
n of the device e is 4W.
ed with a Seria al Port connec
e MikroTik Win nbox utility. W
.88.1 with the e username ad
vailable, Winb box can also b
i.mikrotik.com m/wiki/First_
device from n etwork, for ex
he LED light t urns off, and
oove to a pole, , you can do it
he loops arou nd the Groov
avoid connect ting a loose Et
t is not pulling g the port. It is
ure that the ca able doesn't d
nd Ports
/n wireless, 1x x1 MIMO, stat
port, support ing automatic
cable for con nnecting to ot
ector.
ore information. Contact suppor
ve 5Hn n
nformatio on
n outdoor case e, with a built
one 10/100 E thernet conne
with a 24V po ower adapter,
ernet cable to o the Ethernet
e Ethernet cab ble, and push
PoE injector
88.1 for config guration
ssive PoE):
Ethernet 8-30 0V DC. Packa
ctor, so initial connection h
Winbox should d be used to c
dmin and no password.
be used to con nnect to the M
_time_startup p
xample to use e MikroTik Ne
Groove will st tart to look fo
t with the pro ovided mount
ve though the provided edg
thernet cable to the Ethern
s recommend ded to secure t
damage the po ort by it's weig
tion mode
c cross/straig ht cable corre
ther network devices. The
rt@mikrotik.com m for support qu
‐in 5GHz
ector which
a PoE injecto or and
t port
it into the cas se
age contains a a 24V
has to be done e via
onnect to the e
MAC address o of the device.
tinstall, hold t the RESET but
r Netinstall se ervers.
ing loops. The e Groove com
e markings, a and around th
net port, secur re the cable t
the Ethernet c cable less tha
ght, or doesn' 't fall out.
ection (Auto M MDI/X), so yo
Ethernet por rt accepts 8-3
uestions.
More
tton of the
es bundled w with
e pole where it
o a wall or the e
n 2m from th e
ou can use eit ther
30V DC powe ring
28-Apr-201 1