Product Safety Information; Product Specifications; Installation And Lubrication - Ingersoll-Rand 295A Series Product Information

Product Safety Information

Intended Use:
These Air Impact Wrenches are designed to remove and install threaded fasteners.
For additional information, refer to Product Safety Information Manual Form 04580916.
Manuals can be downloaded from ingersollrand.com

Product Specifications

Models Style
285B Inside
285B-A Trigger
285B-6 Inside
285B-6A Trigger 6" Extended
Inside
285B-S6
Trigger 6" Extended
Outside
285B-6-AP
Trigger 6" Extended
Pistol
295A
Grip
Pistol
295A-6
Grip 6" Extended
Models Style
285B Inside
285B-A Trigger
285B-6 Inside
285B-6A Trigger
Inside
285B-S6
Trigger
Outside
285B-6-AP
Trigger
Pistol
295A
Grip
Pistol
295A-6
Grip
† K = 3dB measurement uncertainty
pA
‡ K = 3dB measurement uncertainty
wA
* K = measurement uncertainty (Vibration)
Sound and vibration values were measured in compliance with internationally recognized test standards. The exposure to the user in
a specific tool application may vary from these results. Therefore, on site measurements should be used to determine the hazard level
in that specific application.

Installation and Lubrication

Size air supply line to ensure tool's maximum operating pressure (PMAX) at tool inlet. Drain condensate from valve(s) at low point(s) of piping,
air filter and compressor tank daily. Install a properly sized Safety Air Fuse upstream of hose and use an anti-whip device across any hose
coupling without internal shut-off, to prevent hose whipping if a hose fails or coupling disconnects. See drawing 47132790 and table on page 2.
Maintenance frequency is shown in a circular arrow and defined as h=hours, d=days, and m=months of actual use. Items identified as:
1. Air filter
2. Regulator
3. Lubricator
4. Emergency shut-off valve
Parts and Maintenance
When the life of the tool has expired, it is recommended that the tool be disassembled, degreased and parts be separated by material so that
they can be recycled.
Original instructions are in English. Other languages are a translation of the original instructions.
Tool repair and maintenance should only be carried out by an authorized Service Center.
Refer all communications to the nearest Ingersoll Rand office or distributor.
45573011_ed9
Tools running at 90 PSI Air Pressure
Drive
Impacts
per Min.
Type Size
Square 1" 700
Square
1" 700
Spline
#5 700
Square
1" 700
Square 1" 700
Square
1" 700
Tools running at 120 PSI Air Pressure
Drive
Impacts
per min.
Type Size
Square 1" 830
Square
1" 830
6" Extended
Spline
#5 830
6" Extended
Square
1" 830
6" Extended
Square 1" 830
Square
1" 830
6" Extended
5. Hose diameter
6. Thread size
7. Coupling
8. Safety Air Fuse
Recommended Sound Level dB(A)
Torque Range
ft-lb (Nm) † Pressure (L
100-900
103.4
(136-1220)
100-900
103.4
(136-1220)
100-900
103.4
(136-1220)
100-900
103.4
(136-1220)
100-900
101.1
(136-1220)
100-900
101.1
(136-1220)
Recommended Sound Level dB(A)
Torque Range
ft-lb (Nm) † Pressure (L
120-1080
107.0
(163-1464)
120-1080
107.0
(163-1464)
120-1080
107.0
(163-1464)
120-1080
106.2
(163-1464)
120-1080
102.5
(163-1464)
120-1080
102.5
(163-1464)
WARNING
9. Oil
10. Grease - during assembly
Vibration (m/s²)
(ISO 15744) (ISO 28927-2)
) ‡ Power (L ) Level
p w
114.4 8.0
114.4 9.0
114.4 9.0
114.4 9.0
112.1 8.6
112.1 9.1
Vibration (m/s²)
(ISO 15744) (ISO 28927-2)
) ‡ Power (L ) Level
p w
118.0 16.5
118.0 13.3
118.0 13.3
117.2 13.3
113.5 12.7
113.5 12.3
EN
*K
1.2
2.7
2.7
2.7
1.0
2.9
*K
3.4
2.1
2.1
2.1
2.5
3.8
EN-1