Advertisement
Quick Links
P.O. BOX 11846 TUCSON, AZ 85734
(520) 294-3292
• FAX (520) 741-2837
www.iotaengineering.com
INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
CAUTION – To prevent electrical shock, do not mate unit connector until installation is complete and A.C.
1.
power is supplied to the unit.
2.
CAUTION – This fixture provides more than one power supply output source. To reduce the risk of electrical
shock, disconnect both normal and emergency sources by turning off the A.C. branch circuit and by discon-
necting the unit connector.
3.
CAUTION – This is a sealed unit. Components are not replaceable. Replace the entire unit when necessary.
CAUTION – Installation and servicing should be performed by qualified personnel only. De-energize before
4.
opening.
The ILB-CP-HE is for use with grounded LED luminaires listed to UL standards. Not for use in heated air
5.
outlets or hazerdous locations.
6.
The ILB-CP-HE requires an unswitched A.C. power source of 120 to 277 volts AC, 50/60Hz.
The ILB-CP-HE and A.C. driver must be on the same branch circuit.
7.
8.
Do not mount near gas or electric heaters.
The ILB-CP-HE should be mounted in locations and at heights where it will not readily be subjected to tam-
9.
pering by unauthorized personnel.
The ILB-CP-HE will supply 10-60VDC output at the individual rated specification for 90 minutes. See individual
10.
units for output specifications.
11.
The ILB-CP-HE is certified in the CA Title 20 Modernized Appliance Efficiency Database System (MAEDBS)
as a small battery charger.
12.
Suitable for use in damp locations and plenum spaces.
13.
Suitable for Luminaires, recessed Type IC (intended for insulation contact).
14.
For use in 0° C minimum, 55° C maximum ambient temperatures.
15.
The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition, void
warranty, and result in non-compliance with UL specifications.
16.
Do not use this equipment for other than intended use.
17.
Install in accordance with the National Electrical Code and local regulations.
18.
Lighting fixture manufacturers, electricians, and end-users need to ensure product system compatibility before
final installation. See addendum for compatibility and covered luminaire requirements.
EMERGENCY LED DRIVER FOR USE
WITH LED LUMINAIRES IDENTIFIED
IN THE MANUFACTURER'S
INSTALLATION INSTRUCTIONS
E473237
SAVE THESE INSTRUCTIONS
HIGH EFFICIENCY PERFORMANCE
MEETS CA T20 BATTERY CHARGER
EFFICIENCY STANDARDS
ILB-CP-HE
'R-J' MOUNTING DESIGN
HIGH EFFICIENCY EMERGENCY
LIGHTING EQUIPMENT
FOR LED
Patented. See iotaengineering.com/patents for more details
Advertisement
Related Manuals for IOTA ILB-CP-HE Series
Summary of Contents for IOTA ILB-CP-HE Series
- Page 1 ILB-CP-HE ‘R-J’ MOUNTING DESIGN HIGH EFFICIENCY EMERGENCY LIGHTING EQUIPMENT P.O. BOX 11846 TUCSON, AZ 85734 FOR LED (520) 294-3292 • FAX (520) 741-2837 www.iotaengineering.com Patented. See iotaengineering.com/patents for more details INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS CAUTION –...
-
Page 2: Installation Instructions
Chart for output specifications of the unit being installed. 1. The ILB-CP-HE series has been evaluated to and found compliant to UL standard 924. The as-installed performance of system must meet or exceed all Federal, State, and Local code requirements. -
Page 3: Completing Installation
4. MOUNTING THE TBTS TEST ACCESSORY Select a convenient location on the side of the reflector so that the TBTS (on flex conduit marked “B”) can be seen ″ hole ( ″ knockout). Remove the knurled nut after installation. Allow for proper clearance and drill or punch a ″... -
Page 4: Testing And Maintenance
TESTING & MAINTENANCE Pressing the TBTS turns off the light on the TBTS and forces the unit into emergency mode, interrupting power to the designated A.C. driver. The LED load is now being lit by the ILB-CP-HE unit. After releasing the TBTS, the fixture returns to normal operation after a momentary delay. - Page 5 The purpose of this addendum is to sufficiently identify electrical compatibility and predictable emergency light output of the LED luminaire when used with the IOTA ILB-CP Series LED emergency drivers. Verification of these operating traits does not constitute a code-compliant, as-installed emergency egress system. It is still the responsibility of the Designer/ Specifier to assure appropriate light levels are achieved during emergency operation of the luminaire in accordance with Federal, state and local municipal codes regarding path of egress illumination.