Installation - Riello Vokera VIBE MAX User Instructions

4

INSTALLATION

NOTE
Please refer to 3 - 3E and use the appropriate PPE when
carrying out any of the actions or procedures contained within
this section.
4.1 PREPARATION FOR MOUNTING THE
APPLIANCE
The appliance should be mounted on a smooth, vertical sur-
face, which must be capable of supporting the full weight of
the appliance. Care should be exercised when determining the
position of the appliance with respect to hidden obstructions
such as pipes, cables, etc.
When the position of the appliance has been decided – using
the template supplied – carefully mark the position of the anchor
holes (see Fig. 7) and flue-hole (if applicable).
Ensure that the anchors are securely fixed to support the ap-
pliance weight.
Fig. 7
4.2 FITTING THE FLUE
This appliance incorporates a 'click-fit' flue connection at the
top of the appliance.
4.2.1 CONCENTRIC HORIZONTAL FLUE
These instructions relate specifically to the installation of this
appliance with the Vokera 60/100mm 'X-type' (click-fit) flue
terminals accessories. For specific instructions on installing this
appliance with an alternative Vokera flue system, e.g. 80/125mm;
please refer to the instructions supplied with the specific flue
system, or download the instructions from the Vokera website.
The appliance flue outlet elbow can be rotated through 360º
on its vertical axis. In addition the flue may be extended from
the outlet elbow in the horizontal plane. A reduction must also
be made to the maximum length (see table below) when ad-
ditional bends are used.
Reduction for additional bends
Bend
45º bend
90º bend
Horizontal/Vertical flue terminals and accessories
Part No.
20122759
20122761
20122763
20132060
20132061
20132062
20132059
20132058
20131979
20142842
20142841
20132050
20135582
20135587
20121903
A
Fig. 7: Using the template (A) mark and drill a 125mm hole for
the passage of the flue pipe. Both horizontal terminals (fixed
& telescopic) have an eccentric configuration, that enables
condense fluid to drain back to the appliance; consequently
the terminals should be installed level.
NOTE: any horizontal runs that incorporate extensions, must
have a 3-degree fall-back to the appliance.
C
4.2.2 FITTING THE HORIZONTAL FLUE KIT
Carefully measure the distance from the centre of the appliance
flue outlet to the edge of the finished outside wall (dimension X).
Add 65mm to dimension X to give you Dimension Y (see Fig. 9).
Measure dimension Y from the terminal end of the concentric
flue pipe and cut off the excess ensuring any burrs are removed.
Pass the concentric flue pipe through the previously drilled hole.
Fit the flue bend to the boiler flue outlet and insert the concentric
flue pipe into the flue bend ensuring the correct seal is made.
NOTE (Fig. 8): The appliance incorporates a 'click-fit' flue
connection. Ensure that both screws 'C' on the 'click-fit' have
been slackened off. Ensure that the connector is correctly aligned
with the 'click-fit' and insert it into the 'click-fit' until it clicks into
position (this is when the tabs at points 'A' are located in the
groove of the flue bend connector). Both screws (C) should
now be tightened.
NOTE
Fit the internal (white) trim to the flue assembly prior to
connecting the flue pipe to the bend.
You must ensure that the entire flue system is properly supported
and connected. Seal the flue assembly to the wall using
cement or a suitable alternative that will provide satisfactory
weatherproofing. The exterior trim can now be fitted.
Reduction in maximum flue length for each bend
1.0 metre
1.0 metre
Description
XF Horizontal 'Click fit' Flue Kit
XT Telescopic 'Click fit' Flue Kit
XV Vertical 'Click fit' Flue Kit
0.5-Metre Extension
1.0-Metre Extension
2.0-Metre Extension
90-Degree Bend
45-Degree Bend x 2
Telescopic Extension
PMK Plume Kit
45° Plume divertor
Pitched Roof Flashing
Flat Roof Flashing
Wall Brackets
Vert. Connector 'Click Fit' VC
A
B
A
C
Length/Size
796mm C/E
400-575mm C/E
1000mm + VC
500mm
1000mm
2000mm
N/A
N/A
372/519mm
1370mm
N/A
500mm x 500mm
340mm Dia.
208mm C/E
131mm
Fig. 8
17