Related Manuals for Vallox 3722
Summary of Contents for Vallox 3722
- Page 1 Model Document Vallox 096 MV D5326 Vallox 110 MV Vallox 145 MV Valid from 3.2.2015 Type 3722 Updated 3702 6.10.2018 3712 Manual Ventilation units...
-
Page 2: Table Of Contents
Dimensioning figure and space required for installation of the Vallox Silent Klick water seal ....... . . 10 Space required by the alternative Vallox Silent Klick water seal installation method (elbow) . -
Page 3: Safety
INTENDED USE All Vallox ventilation units have been designed to provide appropriate and continuous ventilation so as to present no threat to health and to maintain structures in good condition. IMPORTANT In order to ensure that the indoor air presents no harm to health and remains optimal also for the structures of the building, ventilation must be kept on without disruptions. -
Page 4: Safety Signs Used In The Instructions
Models Vallox 096 MV and Vallox 110 MV can be mounted either on the wall, or on the ceiling by using a mounting plate (optional). • Vallox 145 MV can be mounted either on the wall, or on the floor by using a floor rack (optional). •... -
Page 5: Ventilation Unit Control
At the same time you create a MyVallox Cloud account for yourself. Read more about the service at www.myvallox.com. Ventilation unit control options. Operation of the Vallox ventilation unit can be controlled by the following means: • Through the control panel installed in the building •... -
Page 6: Main Parts
MAIN PARTS Vallox 096 MV, Vallox 110 MV, and Vallox 145 MV R model in the figure Extract air fan Post-heating radiator (behind the protective cover) (behind the extract air duct) Supply air fan Safety switch (behind the protective cover) -
Page 7: Installation
30 mm. Note that during mounting the unit rises 10 mm higher than the final height. Mount Vallox 096 MV, 110 MV, and Vallox 145 MV on the wall with a mounting plate, as shown in the adjacent figure. Make sure that the unit is horizontally level after mounting. -
Page 8: Installing The Ventilation Unit To The Ceiling Mounting Plate
Installing the ventilation unit to the ceiling mounting plate Install the ceiling mounting plate with M8 thread bars so that it is horizontally level. NOTE The end of the thread bars must be 5 mm or less below the fastening nut. Do not fasten the ceiling mounting plate too tight to the ceiling. -
Page 9: Vallox 145 Mv
MOUNTING ON A BASE NOTE Vallox 145 MV must always be installed on a base on the floor, or on the wall using a mounting plate. The base is optional. Adjust the base with adjusting legs to level it. Remove the (4 pcs) rubber plugs at the bottom of the unit. -
Page 10: Vallox 096 Mv, Vallox 110 Mv, And Vallox 145 Mv
Dimensioning figure and space required for installation of the Vallox Silent Klick water seal Vallox 096 MV... -
Page 11: Dimensions And Duct Outlets
3. Supply air from the unit to the Measurement points after the outlet collar. The fan curves indicate the total pressure accounted for by duct losses. apartment 4. Extract air from the apartment to the unit © Vallox Oy - All rights reserved... -
Page 12: Vallox 110 Mv
Vallox 110 MV Main parts Dimensions and duct outlets Dimensions R model in the figure. In the L model, the parts are mirrored 1. Extract air fan 6. Supply air filter G4 (behind the protective cover) 7. Extract air filter G4 2. -
Page 13: Vallox 145 Mv
3. Supply air from the unit to the Extract air apartment Measurement points after the outlet collar. The fan 4. Extract air from the apartment to the curves indicate the total pressure accounted for by unit duct losses. © Vallox Oy - All rights reserved... -
Page 14: Maintenance
To replace the filters: Disconnect the ventilation unit from the mains electricity supply. 2. Lift the latch to open the door of the Vallox ventilation unit. 3. Lift the door off. CAUTION The door is heavy. -
Page 15: Cleaning The Heat Recovery Cell (User)
To check and clean the heat recovery cell: Disconnect the ventilation unit from the mains electricity supply. 2. Open the Vallox ventilation unit door by first lifting the latch fully up and then lowering it back a little way. 3. Lift the door off. -
Page 16: Cleaning The Fans (Installer)
Disconnect the ventilation unit from the mains electricity fan blade balancing weights. supply. 2. Lift the latch to open the door of the Vallox ventilation unit. 3. Lift the door off. CAUTION The door is heavy. 4. Remove the extract air filter (C), the cell top bracket (E) and the heat recovery cell (D). - Page 17 12. Close the door. Ensure that the safety switch catch of the door is touching the safety switch. 13. Plug the ventilation unit back into the mains. The fan has now been checked and cleaned. © Vallox Oy - All rights reserved...
-
Page 18: Cleaning The Extract Air Fan
Cleaning the extract air fan To clean the extract air fan, proceed as follows: Disconnect the ventilation unit from the mains electricity supply. 2. Lift the latch to open the door of the Vallox ventilation unit. 3. Lift the door off. CAUTION The door is heavy. -
Page 19: Technical Specifications
ADJUSTMENT POSITION / AIR FLOWS (supply/extract) Adjustment position 100% Air flow dm /s (l/s) 14/15 31/30 48/44 60/54 68/62 82/74 92/83 98/89 Air flow m 50.4/54 111.6/108 172.8/158.4 216/194.4 244.8/223.2 295.2/266.4 331.2/298.8 352.8/320.4 , dB (A) © Vallox Oy - All rights reserved... - Page 20 TECHNICAL SPECIFICATIONS Product titles Product numbers HVAC codes Additional heating Power, 900W Vallox 110 MV R 3446650 7912039 radiator Vallox 110 MV L 3446750 7912040 Air volumes Supply air 107 l/s, 386m /h, 100Pa Fans Supply air 0.119kW, 0.9A EC...
- Page 21 ADJUSTMENT POSITION / AIR FLOWS (supply/extract) Adjustment position 100% Air flow dm /s (l/s) 36/39 56/62 68/74 81/89 92/98 105/113 116/126 131/142 Air flow m 129.6/140.4 201.6/223.2 244.8/266.4 291.6/320.4 331.2/352.8 378/406.8 417.6/453.6 471.6/511.2 , dB (A) © Vallox Oy - All rights reserved...
-
Page 22: Internal Electrical Connection
INTERNAL ELECTRICAL CONNECTION Vallox 096 MV 230V 50Hz MB_A MB_A MB_B MB_B +24V +24V RS_A RS_A RS_B RS_B TESTER +24V +24V RS_A RS_A RS_B RS_B +11V1 +24V AN/I D/I1 RM/I +24V D/I2 RM/O 1 2 3 4 5 6 °C °C... -
Page 23: Vallox 110 Mv, And Vallox 145 Mv
Vallox 110 MV, and Vallox 145 MV 230 V 50 Hz MB_A MB_A MB_B MB_B +24V +24V RS_A RS_A RS_B RS_B TESTER +24V +24V RS_A RS_A RS_B RS_B +11V1 +24V AN/I D/I1 +24V RM/I D/I2 RM/O 1 2 3 4 5 6... -
Page 24: External Electrical Connection
EXTERNAL ELECTRICAL CONNECTION 7028350 2014-08-29 JS MyVallox Control MyVallox REMOTE 0.3W MONITORING transmitter Modbus RTU 2x2x0,5+0,5 2x2x0,5+0,5 MyVallox MyVallox 2x2x0,5+0,5 Control transmitter 1.2W 2x2x0,5+0,5 2x2x0,5+0,5 External temperature Analog input sensor two different 2x0,5 2x0,5 NTC 4K7 functions 2x0,5 2x0,5 2x0,5 Potential-free contact data 24VDC can be programmed to display... -
Page 25: Duct Radiator Operation Chart
NOTE: COOLING ventilation unit. In this case, the pump and the solenoid valve can be controlled using a Vallox MV ventilation unit, The value set for the and no separate thermostats are needed. -
Page 26: Exploded View And Parts List
EXPLODED VIEW AND PARTS LIST Vallox 096 MV NO. PART CODE PART CODE PART CODE Post-heating resistor Supply / extract air fan 1108800 Bypass flap assembly 900W (R and L 942210 (with a hood) models) 935365 R model 3491200 Door... -
Page 27: Vallox 110 Mv
MyVallox carbon Upper support for 3426600 RJ45 extension cable 952196 dioxide sensor 949111 HR cell (optional) Filter stand (G4, Post-heating resistor 3426800 extract) 900W Filter (G4, extract) 978043 R model 942211 L model 942210 © Vallox Oy - All rights reserved... -
Page 28: Vallox 145 Mv
Vallox 145 MV NO. PART CODE NO. PART CODE NO. PART CODE Supply / extract air Post-heating resistor 1109200 Bypass flap assembly fan (with a hood) 900W 935285 R model 3475900 R model 942211 Wall mounting 3482100 L model 3475901... -
Page 29: Conformity Certificates
CONFORMITY CERTIFICATES... - Page 32 Vallox Oy | Myllykyläntie 9-11 | 32200 LOIMAA | FINLAND Customer service +358 10 7732 200 | Aftersales +358 10 7732 270...
Need help?
Do you have a question about the 3722 and is the answer not in the manual?
Questions and answers