Table of Contents
Advertisement
Quick Links
STORM
INSTRUCTIONS FOR
400W 230V
Oscillating Multi-Tool Kit
Stock No.83648
Part No.MT400SF
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS PRODUCT.
GENERAL INFORMATION
These instructions accompanying the product are the original instructions. This document is part of the product, keep it
for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and
contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions
contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Related Manuals for Draper Storm Force 83648
Summary of Contents for Draper Storm Force 83648
- Page 1 AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
-
Page 2: Title Page
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
CONTENTS CONTENTS PAGE CONTENT PAGE TITLE PAGE INTRODUCTION ....................2 REVISION HISTORY....................2 UNDERSTANDING THIS MANUAL ...............2 COPYRIGHT NOTICE....................2 CONTENTS CONTENTS ......................3 GUARANTEE GUARANTEE ......................4 INTRODUCTION SCOPE ........................5 SPECIFICATION ......................5 HANDLING & STORAGE ..................5 HEALTH & SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE .........6 - 7 ADDITIONAL SAFETY INSTRUCTIONS ..............7 - 8 CONNECTION TO THE POWER SUPPLY..............8 TECHNICAL DESCRIPTION... -
Page 4: Guarantee 3.1 Guarantee
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period. -
Page 5: Introduction
INTRODUCTION 4.1 SCOPE For detail and finishing work such as sanding, cutting, scraping, etc. It is intended for domestic and light commercial use only. Any other application is considered as misuse. 4.2 SPECIFICATION Stock no..........................83648 Part no........................... MT400SF Rated voltage ......................230V~50Hz Rated input ........................ -
Page 6: Health & Safety Information
HEALTH & SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS General Power Tools Safety Warnings WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool”... -
Page 7: Additional Safety Instructions
HEALTH & SAFETY INFORMATION g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust related hazards. 4) Power Tool Use And Care a) Do not force the power tool. -
Page 8: Connection To The Power Supply
HEALTH & SAFETY INFORMATION Excessive force will reduce the working efficiency and cause motor overload. Replacing the accessory regularly will maintain optimum working efficiency. Maintain tool with care NOTE: Remove plug from the socket before carrying out any adjustment, servicing or maintenance. -
Page 9: Technical Description
TECHNICAL DESCRIPTION 6.1 IDENTIFICATION On/off switch. Variable speed control. Plug & cable. Flange. Bolt. -
Page 10: Unpacking & Checking
Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Help Line (the telephone number appears on the Title page) and do not attempt to use the multi-tool. -
Page 11: Basic Multi-Tool Operations
BASIC MULTI-TOOL OPERATIONS 8.1 ATTACHING THE SANDING PADS - FIG.1 FIGS. 1 - 2 NOTE: Switch off the Multi-Tool and remove the plug from the power socket before carrying out adjustments, servicing or maintenance. Caution: For all work or when changing application tools, always wear protective gloves. -
Page 12: Using The Variable Speed Control
BASIC MULTI-TOOL OPERATIONS 8.4 USING THE VARIABLE SPEED CONTROL - FIG.5 FIG. 5 Select oscillation frequency (speed) while the motor is running. The variable speed control can be used to set the optimum oscillating frequency according to the accessories used and the respective application. HIGH OSCILLATION FREQUENCY: Sanding, sawing, rasping and polishing stone and metal. -
Page 13: Maintenance
MAINTENANCE 9 .1 MAINTENANCE & PARTS REPLACEMENT Regular inspection and cleaning reduces the necessity for maintenance operations and will keep your tool in good working condition. The motor must be correctly ventilated during tool operation. For this reason avoid blocking the air inlets. -
Page 14: Optional Accessories
10. OPTIONAL ACCESSORIES Stock No. Part No. Description Application For plastic, fibreglass, wood, putty, HSS segment saw blade. nonferrous metals, sheet steel up to 26057 APT300A(U) approx 1mm, idea working in 63 x 0.8mm, 18TPI. corners. For plastic, fibreglass, wood, putty, HSS segment saw blade. - Page 15 10. OPTIONAL ACCESSORIES Stock No. Part No. Description Application Sanding pad. For sander with dust extraction 26101 APT300P(U) 90 x 90 x 90mm. Sanding sheets for sanding pad. 26106 APT300Q(U) For sander with dust extraction 90 x 90 x 90mm. 10pc. HCS plunge cutter.
-
Page 16: Explanation Of Symbols
11. EXPLANATION OF SYMBOLS 11.1 EXPLANATION OF SYMBOLS Warning! Wear dust mask. Warning! Read the instruction manual Warning! Warning! Wear suitable eye/face Wear ear defenders. protection. WEEE Do not dispose of Waste Electrical & Electronic Equipment in with domestic rubbish Class II construction (Double insulated). -
Page 17: Disposal
12. DISPOSAL 12.1 DISPOSAL - At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. - Contact your local authority for details of collection schemes in your area. In all circumstances: •... - Page 18 NOTES...
- Page 19 NOTES...
- Page 20 - Sales Desk: (023) 8049 4333 - General Enquiries: (023) 8026 6355 - Service/Warranty Repair Agent For aftersales servicing or warranty repairs, please contact the Draper Tools Help Line for details of an agent in your local area. YOUR DRAPER STOCKIST RDCH0816...
Need help?
Do you have a question about the Storm Force 83648 and is the answer not in the manual?
Questions and answers