Table of Contents
Advertisement
Quick Links
STORM
INSTRUCTIONS FOR
12-25mm
Air Stapler
Stock No.14608
Part No.SFASK1025
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS PRODUCT.
GENERAL INFORMATION
These instructions accompanying the product are the original instructions. This document is part of the product, keep it
for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and
contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions
contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper Storm Force SFASK1025
Summary of Contents for Draper Storm Force SFASK1025
-
Page 1: General Information
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product. -
Page 2: Title Page
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
CONTENTS 2.1 CONTENTS PAGE CONTENT PAGE TITLE PAGE INTRODUCTION ......................2 REVISION HISTORY ....................... 2 UNDERSTANDING THIS MANUAL ................2 COPYRIGHT NOTICE ..................... 2 CONTENTS CONTENTS ........................3 GUARANTEE GUARANTEE ......................... 4 INTRODUCTION SCOPE ........................... 5 SPECIFICATION......................5 HEALTH & SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE ........ -
Page 4: Guarantee
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period. -
Page 5: Introduction
INTRODUCTION 4.1 SCOPE This air stapler is designed to insert steel staples. Any other use is forbidden. 4.2 SPECIFICATION Stock no..........................14608 Part no......................... SFASK1025 Operating Air Pressure..................60-100PSI (4-7Bar) Max. Safety Working Pressure..................115PSI (8Bar) Min. Air Hose Size ....................... "... -
Page 6: Health & Safety Information
HEALTH & SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe. Common sense and a respect for the tool will help reduce the risk of injury. Read the instruction manual fully. - Page 7 HEALTH & SAFETY INFORMATION Move the machine as instructed. If the machine is hand held, do not carry it by the air line. If the product is heavy; employ a second or third person to help move it safely or use a mechanical device.
-
Page 8: Additional Safety Instructions For Air Stapler/Nailer
HEALTH & SAFETY INFORMATION 5.2 ADDITIONAL SAFETY INSTRUCTIONS FOR AIR STAPLER/NAILER Only those fasteners listed in the operating instructions may be used in the fastener driving tools. Do not use on scaffoldings and ladders. Check prior to each operation that the safety and triggering mechanism is functioning properly and that all nuts and bolts are tight. -
Page 9: Residual Risk
HEALTH & SAFETY INFORMATION 5.3 RESIDUAL RISK Important note: Although the safety instructions and operating manuals for our tools contain extensive instructions of safe working with power tools, every power tool involves a certain residual risk which can not be completely excluded by safety mechanisms. Power tools must therefore always be operated with caution! -
Page 10: Technical Description
TECHNICAL DESCRIPTION 6.1 IDENTIFICATION Trigger. STAPLE: Hand Grip. Crown. Air Inlet. Length. Magazine Latch. Shank Thickness. Magazine. Shank Width. Safety Latch. Exhaust. -
Page 11: Unpacking & Checking
Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Helpline (the telephone number appears on the Title page) and do not attempt to use the product. -
Page 12: Air Supply
Draper range (see you local Draper stockist) which with proper maintenance will ensure a constant supply of dry air and lubricating oil at all times (see illustration below). Always check machine operating pressure before use. -
Page 13: Assembly
To connect the air ratchet to an air line, a ¼"BSP male thread whip hose* will be required. Wind a length of PTFE tape** around the thread before securing the hose in place. The connection must be tight for an airtight union. * Draper Stock No.54438. ** Draper Stock No.63389. -
Page 14: Operation And Use
10. OPERATION AND USE 10.1 LOADING THE STAPLER - FIGS. 3 - 6 FIG.3 NOTE: Always disconnect the tool from the air supply before any adjustment or maintenance is carried out. Press the magazine latch and gently slide the magazine back. -
Page 15: Safety Latch
10. OPERATION AND USE 10.2 SAFETY LATCH - FIGS. 7 - 8 FIG.7 This tool is fitted with a safety latch on the trigger, which should be engaged when the tool is NOT in use. To operate the air stapler, slide the safety latch to one side, then pull the trigger to fire. -
Page 16: Clearing A Jam
10. OPERATION AND USE 10.3 CLEARING A JAM - FIGS. 9 - 10 Note: Always disconnect the tool from the air supply before any adjustment or maintenance is carried out. FASTENER JAMMED INSIDE MAGAZINE Open the magazine latch and pull open the magazine. Remove the fastener that is causing the obstruction using long nose pliers. -
Page 17: Maintenance
11. MAINTENANCE 11.1 EVERY-DAY MAINTENANCE CHECKS Before connection to the air supply: • Drain the compressor reservoir of condensate. • Drain the air lines of condensate. • Drain the combined separator filter, regulator, water trap. • Fill up the combined separator filter, regulator, lubricant reservoir with approved air tool oil. -
Page 18: Optional Accessories
12. OPTIONAL ACCESSORIES +0.02 -0.055 † STAPLES Approx.2,500 pcs. per box -0.2 +0.1 1.25 STOCK No. PART No. Length Gauge 17551 16mm 17552 25mm 17553 32mm 17554 35mm 17555 38mm... -
Page 19: Troubleshooting
• ‘O’ ring throttle valve dislodged • Replace ‘O’ ring or return to from seat inlet valve. service centre. We recommend the use of Draper Air Tool Oil: 250ml = Stock No.34679, 500ml = Stock No.34681, 1Litre = Stock No.34682. -
Page 20: Disposal
14. DISPOSAL 14.1 DISPOSAL - At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. - Contact your local authority for details of collection schemes in your area. In all circumstances: •... -
Page 21: Explanation Of Symbols
15. EXPLANATION OF SYMBOLS Wear safety glasses. Warning! Read the instruction manual Wear ear defenders. - Page 22 NOTES...
- Page 23 NOTES...
- Page 24 - Sales Desk: (023) 8049 4333 - General Enquiries: (023) 8026 6355 - Service/Warranty Repair Agent For aftersales servicing or warranty repairs, please contact the Draper Tools Helpline for details of an agent in your local area. YOUR DRAPER STOCKIST RWKC0516...
Need help?
Do you have a question about the Storm Force SFASK1025 and is the answer not in the manual?
Questions and answers