Jayco Hummingbird Towables 2019 Owner's Manual
  1. Manuals
  2. Brands
  3. Jayco Manuals
  4. Motorhomes
  5. Hummingbird Towables 2019
  6. Owner's manual
Jayco Hummingbird Towables 2019 Owner's Manual

Jayco Hummingbird Towables 2019 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2019
Towables
Owner's Manual
PRINTED ON RECYCLED PAPER
0283457.2019

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hummingbird Towables 2019 and is the answer not in the manual?

Questions and answers

Related Manuals for Jayco Hummingbird Towables 2019

Summary of Contents for Jayco Hummingbird Towables 2019

  • Page 1 2019 Towables Owner’s Manual PRINTED ON RECYCLED PAPER 0283457.2019...
  • Page 3 44,683 people. We’re proud of our results, and we know those numbers show that a little initiative can go a long way. The Jayco EcoAdvantage is our way of making sure endless generations can enjoy the Great Outdoors.
  • Page 5 Table of Contents Section 1: Warranty & Service Factory Tours Options and Equipment Dealer Responsibility Customer Relations To Contact Us About This Manual Warranty Packet Safety Alerts Reporting Safety Defects Customer Responsibility Change Of Address/Ownership Suggestions For Obtaining Service Obtaining Service For Separately Warranted Items Obtaining Service At Our Customer Service Facility Parts and Accessories Section 2: Occupant Safety...
  • Page 6 Table of Contents Entrance Door Rear Backup Camera Prep Campsite Hook-Up Stabilizer Jacks Manual Stabilizer Jacks (if so equipped) Electric Stabilizer Jacks (if so equipped) Emergency Stopping Emergency Towing Wheel Lugs Wheel Lug Nut Diagrams Wheel Lug Nut Torque Values Tires Changing A Tire Spare Tire Carrier (if so equipped)
  • Page 7 Table of Contents GFCI Receptacle Testing The Campsite Power Connection Connecting The Power Cord Power Converter Converter with Charge Wizard (if so equipped) 12-Volt DC System 12-Volt Fuse Panel Replacing A Fuse 12-Volt DC Outlet Auxiliary Battery (customer supplied) Dry Camping Replacement and Maintenance Battery Isolator For Your Tow Vehicle (customer supplied) Battery Disconnect Switch (if so equipped)
  • Page 8 Table of Contents Section 8: Plumbing System Plumbing System Plumbing System Maintenance Monitor Panel Monitor Panel Command Center Operation Fresh Water System Water Pressure Regulator (customer supplied) Fresh Water Holding Tank 12-Volt Water Pump and Switch Fresh Water Connections City Water Fill with City Water Connection Label Water Pump Switch (if so equipped) Potable Water Label Gravity Water Fill...
  • Page 9 Table of Contents Gas Drop-In Cooktops (if so equipped) Kitchen Range and Oven (if so equipped) Oven (if so equipped) Gas BBQ Grill (if so equipped) Attaching the “Quick Coupler” Connection Quick Connect Coupler Gas Grill and Mounting Bracket on Support Rail Range Hood (if so equipped) Refrigerator Range Hood Vent...
  • Page 10 Bunk Bed Ladder (if so equipped) Section 13: Exterior Cleaning the Exterior Frame E-Z Lube or Super-Lube Axle (if so equipped) Exterior Roof and Sidewall Vents Windows Sealants Travel Trailers - Sealant Diagram Section 14: Travel/Camping/Storage Checklists Travel Checklist RV Storage Section 15: Additional Information Featured Components Quick Reference Chart Vehicle Maintenance Record...
  • Page 11 WARNING: Read all instructions in this manual and component manufacturer supplied information before using your RV. This manual has been provided by your recreational vehicle manufacturer for the sole pur- pose of providing instructions concerning the operation and maintenance of this recreational vehicle.
  • Page 12 Maintenance Record Table of Contents...

  • Page 13: Section 1: Warranty & Service

    Canada may differ to conform to Canadian Codes. Dealer Responsibility At the time of sale of the new recreation vehicle, your Jayco dealer is expected to: Deliver your recreation vehicle in the best condition possible. Your recreation ve- hicle must pass the dealer’s pre-delivery inspection (PDI), including all systems...
  • Page 14 (or any effect of the alterations) to any of the parts, components, systems or assemblies installed by Jayco. Jayco is not responsible for the safety or quality of design features, materials or workmanship of any alterations by such suppliers.

  • Page 15: About This Manual

    Canada. In addition, the club offers a variety of local and regional activities throughout the year. By belonging to the Jayco Travel Club, you will find new ways to enjoy your RV and make friends all across the country.

  • Page 16: Warranty Packet

    Section 1: Warranty & Service Warranty Packet There are components that are excluded from the vehicle warranty, or are warranted sepa- rately by their own individual manufacturer’s limited warranty. The Warranty Packet con- tains these component manufacturer supplied manuals or information sheets, warranty cards and/or registrations.

  • Page 17: Reporting Safety Defects

    Section 1: Warranty & Service  Indicates a potentially hazardous situation that, if not avoided, may result in death or serious injury. Reporting Safety Defects In the United States: If you believe that your recreation vehicle has an alleged defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying our Cus- tomer Service Department.

  • Page 18: Customer Responsibility

    Section 1: Warranty & Service Customer Responsibility It is important you read and understand all instructions and precautions before operating the recreation vehicle. Even if you are an experienced RV’er we encourage you to thoroughly read this Owner’s Manual, as well as the information contained in your Warranty Packet and Chassis Guide (motorized only).

  • Page 19: Obtaining Service For Separately Warranted Items

    Section 1: Warranty & Service Please be aware that all service shops require notification of any issues with their repairs within a specified time limit. Make sure you are familiar with their repair policies. Obtaining Service For Separately Warranted Items Your selling dealer is responsible for servicing your recreational vehicle before delivery, and has an interest in your continued satisfaction.
  • Page 20 If a substantial defect in material or workmanship, attributable to Jayco, is found to exist and is reported to Jayco or an authorized servicing dealer during the appli- cable warranty period, it will be repaired or replaced, at Jayco’s option, without charge to the RV owner, in accordance with the terms, conditions and limitations of this limited warranty.
  • Page 21 RV is delivered to the first retail purchaser by an independent, authorized dealer of Jayco, or, if the dealer places the vehicle in service before retail sale, on the date the RV is first placed in such service.
  • Page 22 • defects in materials, components or parts of the structure of the RV not attributable to Jayco; • items that are added or changed after the RV leaves the possession of Jayco; • additional equipment or accessories installed at any dealership, or other place of business, or by any other party, other than Jayco;...
  • Page 23 Certain things completely discharge Jayco from any obligation under this warranty and void it. By way of example, the following shall discharge Jayco from any express or implied warranty obligation to repair or replace any defect that results from: any rental or other busi-...
  • Page 24 In addition, this warranty is not intended to extend to future performance, and nothing in this warranty, or any action of Jayco, or any agent of Jayco, shall be interpreted as an extension of the warranty period or this limitation period.
  • Page 25 Section 1: Warranty & Service Maintenance Record Table of Contents...
  • Page 26 Section 1: Warranty & Service Notes: Maintenance Record Table of Contents...

  • Page 27: Section 2: Occupant Safety

    Section 2: Occupant Safety Secondary Means of Escape (Exit Window) Your recreation vehicle has been equipped with a window(s) that serves as a secondary means of escape. The window(s) will allow a quick exit from the vehicle during an emer- gency if access to the main entrance door is not available.

  • Page 28: Fire Safety

    Section 2: Occupant Safety Lever style latch Remove the screen by pulling the red tab (upper rightarrow). Pull the lever out from the sash clamps. Swing the lever out so it is positioned straight out from the win- dow. Push the lever (and window) out to open and exit the vehicle. Lever style latch Remove the screen by pulling the red tab (upper rightarrow).

  • Page 29: Smoke Alarm

    Section 2: Occupant Safety  Do not check the pressure, test or practice using the fire extinguisher by squeezing the trigger, even briefly. The fire extinguisher is not rechargeable or refillable. Once used, it will gradually lose pressure and will not be fully charged for use in an emergency.

  • Page 30: Combination Carbon Monoxide /Propane Alarm

    Section 2: Occupant Safety alarms low battery warning (beep) starts to assure continued protection. When the battery is removed from the alarm, the battery flag will pop up; the alarm cannot be installed to the mounting bracket without a battery. To test, stand at arm’s length from the smoke alarm as the alarm horn is loud and may be harmful to your hearing.
  • Page 31 Section 2: Occupant Safety The alarm is directly wired to the 12-volt electrical system, with continuous power being supplied by the recreational vehicle batteries. There is no 9-volt battery power supply. As a result, the alarm is always drawing a small amount of current from the recreation vehicle batteries.
  • Page 32 Section 2: Occupant Safety What you should do if the alarm sounds  Actuation of this detector indicates the presence of carbon monoxide which can kill you. Never turn the 12-volt battery disconnect control to the off position and disconnect the battery cable to silence an alarm. The alarm will auto- matically sense when the level of carbon monoxide in the air reaches below dangerous levels.

  • Page 33: Extended Or Full Time Usage

    Section 2: Occupant Safety Testing the combination carbon monoxide/propane alarm  Test the alarm operation after the RV has been in storage, before each trip and at least once per week during use. The TEST/RESET button tests all ELECTRICAL functions of the alarm. The TEST/Mute switch is located on the front of the alarm.

  • Page 34: Cold Weather Usage

    Section 2: Occupant Safety  Continuous or permanent living in your recreation vehicle may affect your warranty coverage and may void the “Limited Warranty” applicable to your vehicle. Cold Weather Usage When used in freezing or below freezing temperatures, the precautions should be taken: Fresh water and drainage systems - preparations to avoid freeze-ups.

  • Page 35: Section 3: Pre-Travel Information

    Section 3: Pre-Travel Information Tow Vehicle If you plan to tow your recreation vehicle with a tow vehicle you already own, or if you plan to purchase a new one, make sure the Gross Vehicle Weight Rating (GVWR) or your recreation vehicle does not exceed your tow vehicles towing rating.
  • Page 36 Section 3: Pre-Travel Information OCCC Label (Occupant & Cargo Carrying Capacity: The upper portion of this yellow label is feder- ally required and includes the maximum Oc- cupant & Cargo Carrying Capacity that may be placed in or on the trailer as it was manufactured and weighed before leaving the factory.

  • Page 37: Loading Your Recreation Vehicle

    Section 3: Pre-Travel Information Loading Your Recreation Vehicle  Never load the RV in excess of the GAWR for either axle. Overload- ing your RV may result in adverse handling characteristics and dam- age to the RV. DO NOT EXCEED YOUR GVWR! This means you should weigh your RV as loaded for your normal travel to determine the actual weight.

  • Page 38: Rear Bumper

    Section 3: Pre-Travel Information Rear Bumper The rear bumper of your RV is not designed to carry cargo. Items that extend beyond the bumper OR weigh over 100 lbs. (45kg) will place undo strain on the bumper. The 100 lb. ...
  • Page 39  Using an oversized or undersized hitch can cause damage to the RV frame. Jayco cannot be responsible for the tow vehicle suspension system. The fi- nal ball height after the tow vehicle/travel trailer combination is completely hooked up is a factor that must be considered. To avoid overloading your trailer axles and minimize possible handling difficulties, your trailer should be level when hooked to your tow vehicle.
  • Page 40 Section 3: Pre-Travel Information Remove the dolly wheel or platform and retract the tongue jack to its maximum height. Attach the breakaway switch cable to the tow vehicle. 10. Attach the safety chains. 11. Plug in your wire harness/connector plug from the tow vehicle to the travel trailer. 12.
  • Page 41 Section 3: Pre-Travel Information Travel Trailer Safety Chains: Your RV is equipped with chains to meet SAE standard requirements for maximum gross trailer weight. Always have the safety chains attached when towing. Install them as shown below so they do not restrict sharp turns, but tight enough so they do not drag on the ground. Crisscross the left safety chain under the coupler and attach to the right mounting slot in the trailer hitch;...

  • Page 42: Wire Harness/Connector Plug

    Section 3: Pre-Travel Information Wire Harness/Connector Plug A 7-way wire harness/connector plug is wired into your trailer to connect electrical power from the tow vehicle for travel. This supplies power to the RV brakes, taillights, clearance lights, turn signals, brake lights, etc. Wiring to operate your brakes must be the same size in both the tow vehicle and RV (the RV brake wiring is 12-gauge wire).
  • Page 43 Section 3: Pre-Travel Information Your RV must be weighed fully loaded (with food, clothing, fuel, water, propane, supplies, etc). Weigh the RV including the tongue weight, while detached from the tow vehicle. This actual overall weight must be less than or equal to the GVWR for safe operation. If the overall weight is greater than the GVWR, some contents must be removed until the actual overall weight is less than or equal to GVWR.
  • Page 44 Section 3: Pre-Travel Information Notes: Maintenance Record Table of Contents...

  • Page 45: Section 4: Vehicle Operation

    Section 4: Vehicle Operation Towing  Your RV braking system is rated for operation at GVWR not GCWR. Whenever possible, do not travel with waste in the holding tanks. Liquid or debris in the holding tank(s) may affect the towing characteristics and may result in property damage or personal injury.
  • Page 46 Section 4: Vehicle Operation have not been affected. Never operate any vehicle if a difference in braking efficiency is noticeable. Electric Brakes The electric brakes are designed to work with the tow vehicle brakes. To maintain proper braking performance, both the RV and tow vehicle brakes must be used to- gether.

  • Page 47: Towing Behind Your Rv

    If you do not have a Jayco factory installed hitch receiver, towing items behind your Jayco RV, or overloading the rear, will void the warranty and may result in: damage to the RV or add-on items, towing difficulties, property dam- age and/or personal injury.

  • Page 48: Entrance Door Step(S)

    Section 4: Vehicle Operation Entrance Door Step(s) Make sure your entrance step is fully extended before exiting the vehicle, and retracted prior to towing. Lubricating the step mechanism Carefully clean the area around the pivot points (the rivets involved in the motion of the mechanism). Lubricate these pivot points with an automotive grade, non-staining lubricant every 30 to 60 days.

  • Page 49: Campsite Hook-Up

    Section 4: Vehicle Operation Rear Backup Camera Prep Your recreation vehicle has been pre-wired to allow for installation of a (customer supplied & customer installed) rear backup camera and a customer installed (or dealer installed) cam- era ON/OFF switch so the backup camera can be used as an observation/security camera. Depending on your RV model, a camera accessory power wire is pre-routed at the factory from the rear camera, to the bedroom or the command center panel inside the entrance door.
  • Page 50 Section 4: Vehicle Operation The stabilizer jacks must be fully retracted before moving or towing the RV to prevent stabilizer jack damage. Each stabilizer jack can be individually adjusted to stabilize the RV for use. When setting up on soft ground, you may wish to place a wood pad or the equivalent under each stabilizer jack foot to help keep the jack from sinking into the ground.

  • Page 51: Emergency Stopping

    Section 4: Vehicle Operation Emergency Stopping Always carry road flares or reflective warning signs. Pull off the roadway as far as possible for emergency stopping. Turn ON your vehicle hazard warning flashers. If traveling at night, use three red warning indicators such as flares, reflectors or lanterns as required by the Uniform Vehicle Code and Model Traffic Ordinance as follows: Place the first warning indicator on the traffic side of the recreation vehicle, directed at the nearest approaching traffic.
  • Page 52 Section 4: Vehicle Operation NOTE: The proper method of tightening wheel lug nuts is with a properly calibrated torque wrench and socket, not with an impact wrench or by hand. Do not use a 4-way lug wrench or any other type of wrench that does not measure the actual pressure applied to the lug nut.
  • Page 53 Section 4: Vehicle Operation Wheel Lug Nut Torque Values Prior to travel and after excessive braking, wheel lug nuts should be checked for torque. Torque readings must fall within the Final Torque Values in chart above. Torque specifications should be checked using a proper torque wrench. If the torque falls below the Final Torque Values, additional torque is required.
  • Page 54 Section 4: Vehicle Operation • Damaged tools must not be used and must be removed from service for evaluation and either reported and re-calibrated or replaced. Do not use accessories or handle extensions unless specifically allowed by the torque wrench manufacturer. Do not use the torque wrench as the primary means of tightening or loosening fasteners.
  • Page 55 Section 4: Vehicle Operation  Tire wear should be checked frequently. Once a wear pattern becomes firmly established in a tire it is difficult to stop, even if the underlying cause is cor- rected. Tire Pressure  Failure to follow proper inflation guidelines may result in tire failure, which, under certain circumstances can cause loss of vehicle control or accidents that may result in property damage, bodily injury and/or death.

  • Page 56: Changing A Tire

    Section 4: Vehicle Operation Changing A Tire  Do not use the stabilizer jacks to support the recreational vehicle while under the vehicle or changing tires. The stabilizer jacks are designed as a stabilizing system only. Do not use the stabilizer jacks as a jack or in conjunction with a jack.

  • Page 57: Spare Tire Carrier (If So Equipped)

    Section 4: Vehicle Operation Spare Tire Carrier (if so equipped) If your recreational vehicle is equipped with a spare tire, it will either be mounted under the unit (hoist) or on the rear bumper.  DO NOT exceed the maximum load capacities of 100 lbs. for the hoist. DO NOT use air driven guns or impact wrenches to lift the spare tire to the travel position.

  • Page 58: Setting Up Your Recreation Vehicle

    Section 4: Vehicle Operation Securing the spare tire To secure the spare tire in the travel position, put the steel hoist lift support located on the end of the cable through the rim of the tire. The hoist lift support clips need to seat inside the center hole of the tire rim.

  • Page 59: Awnings (If So Equipped)

    Section 4: Vehicle Operation Travel Trailer Set Up Unhook the wire harness/connector plug, safety chains and breakaway switch lanyard. Install the dolly wheel or platform. Release the weight distributing bars (customer supplied). Open the tongue jack coupler latch. Turn the tongue jack crank to raise the coupler above the hitch ball. Level the RV (front-to-back) with the tongue jack crank.

  • Page 60: Power Awnings (If So Equipped)

    Section 4: Vehicle Operation Electric Patio Awning With Remote Control NOTE: The electric awning requires connection to a 120-volt power source. Make sure you have sufficient power available before operating your awning (refer to Electrical Systems, Calculating electrical load). In Motion Detector (if so equipped) Some patio awnings are equipped with a motion detector.
  • Page 61 Section 4: Vehicle Operation Adjusting the Awning Pitch  Do not set the individual arm pitch at more than three (3) positions differ- ent between the left and right arms. Damage to the arms and the canopy can occur if the awning is retracted when the arms are set at more than three (3) positions difference.
  • Page 62 Section 4: Vehicle Operation Emergency Operation If power to the vehicle is not available, the awning can be retracted by jumping the motor using a 10VDC – 14VDC power source such as a cordless drill battery or car battery. Remove the front cover (the cover snaps onto the rear cover).
  • Page 63 Section 4: Vehicle Operation Emergency Operation If power to the vehicle is not available, the awning can be re- tracted by jumping the motor using a 10VDC – 14VDC power source such as a cordless drill battery or car battery. Locate and separate the quick disconnects located in the motor arm channel.
  • Page 64 Section 4: Vehicle Operation Maintenance Record Table of Contents...

  • Page 65: Electric Slide Room(S) (If So Equipped)

    Section 5: Slideout Systems Electric Slide Room(s) (if so equipped) The mechanical components of the slide out are gear driven. Electric powered slideout room systems have a manual override to allow you to extend or retract the slideout room(s) in case of a power loss.
  • Page 66 Section 5: Slideout Systems Operating the switch after the room is fully extended or retracted may damage the switch and motor. After the slideout is extended, visually inspect the slideout and the surrounding area to make sure the slideout has extended properly and has adequate clearance from any outside obstructions.
  • Page 67 Section 5: Slideout Systems NOTE: For long-term storage it is recommend the room be closed (retracted). Trouble shooting the flush floor slideout Refer to the general troubleshooting check list before proceeding. Electric Operation NOTE: Install transit bars (if so equipped) on the slideout room during storage and transportation.
  • Page 68 Section 5: Slideout Systems Schwintek In-Wall Slideout System The in-wall slideout system requires no maintenance or adjustments. This system has two vertical columns with a drive motor located at the top of each column. The right and left motors are synchronized by a circuit board. Schwintek slideouts are typically used on both towables and motor homes.
  • Page 69 Section 5: Slideout Systems Trouble shooting the in-wall slideout system Checking Fuses: The in-wall slide requires a minimum 30-amp fuse. Check the load center for blown fuses and replace any if necessary. If the fuse blows immediately upon replace- ment, there is a problem with the wiring to the in-wall slide control box. A qualified service person should be called to check and repair.
  • Page 70 Section 5: Slideout Systems Using either a wall or command center panel switch, press and hold the switch toward the word IN or RETRACT until the unit comes in completely. This will allow you to get the recreation vehicle to a service center to have the slideout malfunction diagnosed. ...
  • Page 71 Section 5: Slideout Systems Error Codes When an error code occurs during operation, the board LEDs lights will indicate where the problem is. For motor specific faults the green LED will blink (1) time for motor #1 and (2) times for motor #2. The red LED will blink 2 to 9 times depending on the error code. Error codes are as follows: ...
  • Page 72 Section 5: Slideout Systems Norco Slideout Manual Operation Locate the included flexible shaft in your own- er’s packet. Attach flexible shaft to the 1/4” hex fitting on the end of the motor. Attach 1/4” socket & ratchet, or drill to the other end, and turn in the proper direction to move the room.
  • Page 73 Section 5: Slideout Systems If the room does not move when the switch is pressed, check the following: Make sure the slideout system is turned on. Battery is fully charged and connected. Transit bars have been removed (if so equipped). ...
  • Page 74 Section 5: Slideout Systems Locate the manual override for the slideout system (Fig. 1). The room is now free to move. Us- ing either a 5/8” or 3/4” wrench or socket, crank the room either in or out completely. If the slideout system is supplied with a gearbox override (op- tional), use the crank handle to move the room.
  • Page 75 Section 5: Slideout Systems Engine or generator must be running, or plugged into shore power. Transmission must be in park or neutral (if applicable). Set the parking brake and level the unit. Remove transit bars (if so equipped) if extending the room;...
  • Page 76 Section 5: Slideout Systems Fault Codes Fault Fault Description Possible Cause Possible Solution Type Code -Stops have not been set Steps need to be programmed by an Major Stops not programmed -Stops were cleared authorized service facility. -Stops were improperly set Run room in opposite direction.
  • Page 77 Section 5: Slideout Systems NOTE: After overriding the system, the room control will need to be re-programmed by an OEM authorized dealer. Emergency Retract Mode: Use this procedure when there is NO loss of power or electrical problem with the system. Remove the touchpad (Fig 4) from the wall.
  • Page 78 Section 5: Slideout Systems Repeat steps 1-4 for the other side. Place a socket wrench with a 3-inch extension and a 5/8” deep well socket (Fig 12) through the motor access opening and seat the socket onto the coupler (Fig 13). One person alternating from side to side of the room can retract a 1500 lb.
  • Page 79 Section 5: Slideout Systems Power Gear Ram Slideout System Typically used for Class C motorhomes. Manual Override Procedure: The system has been equipped with 3/4” hex override couplers located on the drive compo- nent of the system. Due to the size and weight of some rooms, assistance may be needed to push the room in.
  • Page 80 Section 5: Slideout Systems 12. Return the brake release lever back to the “engaged” position (parallel to the spring lock lever). Pressing the bent end of the spring lock lever will allow the brake le- ver to be moved. 13. Plug the motor connector back in again. 14.

  • Page 81: Section 6: Electrical System

    Section 6: Electrical System The Electrical System The RV electrical system is comprised of two independent electrical systems. One operates off of 12-volt DC power and the other off of 120-volt 60hz AC power. All installations have been made in compliance with industry standards applicable on the date of manufacture. Because the electrical equipment and associated circuitry are engineered into a dedicated system specific to your RV, do not make unauthorized changes or add fixed appliances to it.

  • Page 82: Command Center

    Section 6: Electrical System Command Center The command center is typically located inside the entrance door or in the living area of the RV, and contains switches and controls for various electrical functions. Command center applications, configu- rations and components will vary by model. Command Center Panel or Command Center Panel with Switch Modules Items found on these panels may include:...

  • Page 83: Gfci Receptacle

    Section 6: Electrical System GFCI Receptacle There is a ground fault current interrupter (GFCI) engineered into the electrical system. It is designed to reduce the possible injury caused by electric shock. The GFCI will not protect against short circuits or circuit overloads. Test all GFCI receptacles monthly: Push in the GFCI “TEST”...
  • Page 84 Section 6: Electrical System  Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. DO NOT plug the shore power cord into a campsite receptacle(s): That has reverse polarity With non-functioning ground circuits That shows outward signs of heat damage.

  • Page 85: Power Converter

    Section 6: Electrical System The shore line power cord should be unplugged when the recreation vehicle is left unattended. If something would happen to the electrical system, this may help limit potential damage. When you are ready to leave, reverse the power cord connection process. Use care to pre- vent damaging the power cord electrical connection pins when connecting or disconnecting the shore line power cord.
  • Page 86 Section 6: Electrical System An open inline fuse in the battery wire An open wire between the converter and the RV battery Loose ground connection Improper torques If the converter fuses and AC voltage are good, but the converter output still reads zero volts, the converter is not functioning properly.

  • Page 87: Volt Dc System

    Section 6: Electrical System 12-Volt DC System The majority of your recreation vehicle lighting is powered by 12-volt electricity. The 12- volt DC system is composed of components that will operate when the following conditions are met: Power is supplied by the tow vehicle alternator when the engine is running and the 7-way trailer plug is connected.

  • Page 88: Auxiliary Battery (Customer Supplied)

    Section 6: Electrical System Auxiliary Battery (customer supplied)  Do not store anything inside the battery compartment(s) or near the batteries that could touch the battery or battery cable terminals. Contact with the battery or battery cable terminals could cause an electrical short circuit, discharge the batteries, or start an electrical fire.

  • Page 89: Load Center

    Section 6: Electrical System remove the auxiliary battery from your RV, store it in a dry, cool area per the manufacturer’s instructions. When it is time to replace the auxiliary battery, Group 27 or Group 31 true deep cycle batteries are recommended to increase run time of electrical components while dry camping (operating solely on battery power).

  • Page 90: Volt Circuit Breakers

    Section 6: Electrical System Not all load centers will include a main breaker. Motor homes may have separate small panels for breakers and fuses. They are normally located in close proximity to each other typically in the bed platform. The converter is also mounted separately (typically under the bed platform).

  • Page 91: Approximate Electrical Load Ratings

    Section 6: Electrical System Approximate Electrical Load Ratings 12 VOLT SYSTEM Exterior Entertainment Center 5-7 AMPS 1.5 AMPS Furnace 12.0 AMPS Generator Start 95.0 AMPS* Illuminated Switch .125 AMP Inverter variable Leveling System 95.0 AMPS* LP Detector .125 AMP Light; Halogen 1.7 AMPS Light;...

  • Page 92: Volt (30 Amp) Ac System (If So Equipped)

    Section 6: Electrical System 120-Volt (30 AMP) AC System (if so equipped) The 30 amp 120-volt 60hz AC electrical system.is designed to operate on 1 leg of 120-volt power at a maximum current flow of 30 amperes. Exposure to voltages higher or lower than a nominal 120-volts will damage or shorten the service life of the electrical system and appliances.

  • Page 93: Solar Prep (If So Equipped)

    Section 6: Electrical System Always test the external power source (i.e., the campsite power receptacle or electrical box) with a ground monitor before connecting your power cord to it. If the ground monitor indi- cates ‘reverse polarity’ or an ‘open ground’ DO NOT connect the power cord. Regularly inspect the shore power cord for cuts, cracks, worn insulation and other damage.
  • Page 94 Section 6: Electrical System Maintenance Record Table of Contents...

  • Page 95: Exhaust Gas Fumes

    Section 7: Fuel & Propane System Exhaust Gas Fumes  Avoid inhaling exhaust gases as they contain carbon monoxide, which is a potentially toxic gas that is colorless and odorless. If you are in a recreation vehicle with either a nearby tow vehicle engine running or the generator (if so equipped) running there is a potential for exhaust fumes to filter back into the recreation vehicle To avoid breathing exhaust gases, follow these precautions:...
  • Page 96 Section 7: Fuel & Propane System recommended. Hand tighten the LP gas system valves only, do not use a wrench or pliers as over tightening may damage the valve seals and cause them to leak. NOTE: All propane lines have been checked with air pressure at the time of manufacture.
  • Page 97 Section 7: Fuel & Propane System Be sure to securely re-install DOT cylinder(s) after they have been removed for filling or replacement. Always close the service valve and install a dust cap or plug when transporting or storing disconnected containers whether full or empty. ASME tanks are permanently mounted to the RV and are commonly used on RV motor homes.
  • Page 98 Section 7: Fuel & Propane System The position of the propane container(s) and the hoses are critical to proper operation and propane flow. Follow these instructions to make sure your propane container(s) are con- nected properly. LP Gas Container Overfill Never allow your propane tank to be filled above the maximum safe level as indicated by the fixed liquid level gauge.
  • Page 99 Section 7: Fuel & Propane System It also has a left-handed thread, which means that it is turned clockwise to remove, and counter-clockwise to tighten. The P.O.L. fitting has been designed to help restrict the flow of LP gas in the event of a regulator failure or hose malfunction. Propane Regulator ...

  • Page 100: Propane Use And Safety

    Section 7: Fuel & Propane System Propane Use and Safety Propane is a colorless and odorless gas that, in the lique- fied state, resembles water. An odorant (usually a sulfur compound) is added as a warning agent. If you smell propane within the vehicle, quickly and carefully per- form the procedure listed on the propane system label.
  • Page 101 Section 7: Fuel & Propane System If you have double cylinders on your recreation vehicle, use only one at a time. Otherwise, the propane supply will be drawn equally from both cylinders until the supply has been total- ly exhausted. Using one cylinder until it is empty, then using the second cylinder will allow you to fill the empty cylinder at your convenience without running totally out of propane.

  • Page 102: Installing Propane Cylinder(S)

    Section 7: Fuel & Propane System Traveling With Propane NOTE: Some states prohibit propane appliances to be operat- ed during travel, especially in underground tunnels. Make sure you know the laws for the areas where you travel. Use care when fueling your motor fuel tanks and/or propane containers.
  • Page 103 Section 7: Fuel & Propane System Attach the 1/4” inverted flare x 24” Type 1 pigtail hose to the regulator inlet and the right hand swivel nut to the cylinder valve. Secure the cylinder to the A-frame bracket using the bolts, nuts and washers provided. Double Cylinder Mounted On A-Frame (if so equipped) When a second cylinder is installed, a tee check valve is used to replace the 90°...
  • Page 104 Section 7: Fuel & Propane System Notes: Maintenance Record Table of Contents...

  • Page 105: Plumbing System

    Section 8: Plumbing System Plumbing System There are two different water systems in your recreation vehicle: The fresh water system consists of the fresh water holding tank, faucets and con- nections, water pump, outside shower assembly (if so equipped), water heater, tub/ shower, and water purification system (if so equipped).
  • Page 106 Section 8: Plumbing System Operation Press only one tact switch at a time. As you push ei- ther the FRESH, BLK GREY1 or GREY2 switch, one or more LED lights will illuminate (from left to right) indicating the content level for that tank. When push- ing the “BATT”...

  • Page 107: Fresh Water System

    Section 8: Plumbing System Fresh Water System All water contains contaminant and mineral particles that can cause fresh water system odors. Untreated well water is a major source of water system odors. The fresh water (po- table water) system needs periodic sanitization and winterization to take care of all the com- ponents in the plumbing system to discourage the growth of bacteria and other organisms that can contaminate the water supply.

  • Page 108: Fresh Water Connections

    Section 8: Plumbing System Water Pump Switch (if so equipped) Most water pump switches illuminate when the water pump is activated. In most models, the (red) pump switch is located on the monitor panel or the utility center. When the water pump switch is ON the pump runs until 45 lbs.
  • Page 109 Section 8: Plumbing System NOTE: The City Water Fill inlet when connected to a pressurized fresh water source sends water through the water lines and fixtures without the use of the pump. The fresh water tank cannot be filled using the city water fill (the gravity fill is used to fill the fresh water tank).

  • Page 110: Draining The Fresh Water System

    Section 8: Plumbing System Draining the Fresh Water System Water tanks may be drained through a valve located near the tank. A recreational vehicle with a demand pressure pump system will have low-point drains attached to the water lines (normally located near the water tank). These low-point drains will release water in the supply lines by opening the valves and all faucets.
  • Page 111 Section 8: Plumbing System Bypass Mode: operation diverts the flow of water around the water heater keeping water out of the wa- ter heater. Valve handles should be turned so they are pointing in line with the vertical bypass tube (connect- ing both valves together).
  • Page 112 Section 8: Plumbing System the gravity fill. Remove the hose (or funnel) and container used to pour the chlorine solution, and con- tinue filling the fresh water tank with clean (potable) water until tank is full. Pour fresh water into the gravity fill inlet until tank is completely full. After the recommended amount of sanitizing solution is in the tank, the water tank is full, and water filter has been removed and bypassed, turn the pump ON which sends sanitizer into the water lines.w...
  • Page 113 Section 8: Plumbing System Follow the steps outlined in Draining the Fresh Water System with one exception: do not drain the water heater. Water heater bypass valves set to BYPASS (refer to Water Heater Bypass section). Do not remove the water heater drain plug. Remove the cartridge water filter (if equipped) and replace it with the bypass tube included with your RV.
  • Page 114 Section 8: Plumbing System If you chose to perform the winterization process yourself, read and understand the follow- ing information before starting. Contact customer service or your dealer for questions about this process. It may be easier to winterize the RV with another person to assist you. NOTE: The water heater must be drained to prevent damage from freezing.
  • Page 115 Section 8: Plumbing System NOTE: Filters should be replaced at the beginning of the camping season or if they have come into contact with contaminated water or antifreeze. Run the pump until it is dry (approximately 15 to 20 seconds). Operating the pump longer than that with no water can damage the pump.
  • Page 116 Section 8: Plumbing System  Automotive antifreeze (ethylene glycol) and windshield washer antifreeze (methanol) are poisonous. Never use these products in your fresh water sys- tem. These products are harmful and may be fatal if swallowed. NOTE: Antifreeze should never enter the water heater, RV water filter, refrigerator, refrigerator water filter, or fresh water tank.
  • Page 117 Section 8: Plumbing System Winterizing the Macerator System (if so equipped) Ensure all tanks are empty. Pour RV antifreeze into the empty black water tank. (Be sure to have a container available for capturing system fluid) Turn the macerator pump ON. Run the pump until antifreeze begins to discharge from the dump connector attached to the flex hose.

  • Page 118: Water Heater

    Section 8: Plumbing System Water Heater The water heater manufacturer has preset the sensing limit to maintain the water temperature when the water heater is activated.  Hydrogen gas may result if you have not used the water heater for two weeks or more.
  • Page 119 Section 8: Plumbing System Odor from the hot water system Many water supplies contain sufficient amounts of sulfur to produce an odor, often called “sulfur water”. Sulfur water can be caused by a chemical action or by bacteria. Generally, sulfur water is not harmful, only unpleasant to smell. Refer to the water heater manufac- turer’s owner’s manual for details on eliminating the odor from sulfur water.
  • Page 120 Section 8: Plumbing System heating the water because of incomplete combustion of the burner at these higher altitudes. Consult with the local propane company, your dealer or the water heater manufacturer for proper derating of the water heater. Change out of the orifice (derating) should be done by the dealer or a qualified service agency.

  • Page 121: Outside Shower (If So Equipped)

    Section 8: Plumbing System Draining and Winterization: If the recreation vehicle is to be stored over the winter months, the water heater must be drained to prevent damage from freezing. Damage to the water heater caused by freezing is not warrantable. It is recommended the water heater be drained and bypassed during the winterization process, particularly if introducing RV antifreeze into the plumbing sys- tem.

  • Page 122: Bathroom Tub / Shower

    Section 8: Plumbing System Faucets The bathroom, kitchen and outside shower faucets operate much the same way as the faucets in your home. Make sure there is sufficient water available and the 12-volt water pump is turned ON before operating. NOTE: There may be air in the water plumbing lines which needs to be bled out before a steady stream of water comes from the faucet.
  • Page 123 Section 8: Plumbing System By adding water and using a RV approved deodorizing agent you will dissolve the contents faster and will keep the drain lines and tanks clean and free flowing. These chemicals are available at an RV supply store or your dealer. Drain Pipes with Dry Sealing Valve (if so equipped): Your RV may be equipped with a dry sealing valve that prevents the escape of odors from your waste system and...
  • Page 124 Section 8: Plumbing System  Never travel with full black or grey water holding tanks. This not only wastes your fuel but depending on the location of the tank(s), it can affect your tow vehicle handling characteristics.  Never leave the black tank drain in the open position continuously when connected to the campground sewer system.

  • Page 125: Black Tank Flush (If So Equipped)

    Section 8: Plumbing System Please contact your RV dealer for assistance in the purchase and installation of a sewer hose or sewer hose extension (if needed). Sewage (black) tank preparation:  It is important to add enough water to prevent solid waste buildup. Follow the directions listed below and in the manufacturer’s operator manual.
  • Page 126 Section 8: Plumbing System  The black tank drain valve must be OPEN any time there is a hose (water supply) connected to the black tank flush. Do not leave any hose (water supply) connected to the black tank flush when it is not in use.

  • Page 127: Section 9: Heating & Cooling

    Section 9: Heating & Cooling Air Conditioner The air conditioning system is controlled by a thermostat. Cooled air enters the RV through the grill. Make sure you have sufficient power available before operating the air conditioner. Do not operate the air conditioner without the return air filter. Operating the system without the filter allows the lint and dirt that is normally stopped by the filter to accumulate on the cooling coil of the air conditioner.
  • Page 128 Section 9: Heating & Cooling Furnace The furnace installed in your recreation vehicle is controlled by a 12-volt DC thermostat. Depending on your model, there may be up to two thermostats enabling you to control the temperature to your comfort level. The furnace requires both 12-volt power and propane gas for full operation.

  • Page 129: Section 10: Appliances

    Section 10: Appliances Microwave  To prevent damage, remove the turntable from the microwave when trav- eling. Make sure you are connected to a 120-volt power source.  Never use the microwave cavity for storage. The microwave cavity should always be empty when not in use. For details on operation, cleaning and safety information, refer to the manufacturer’s user guide.
  • Page 130 Section 10: Appliances Cooking With Propane (if so equipped) See the Propane System Section for important safety instructions. Refer to the manufactur- er’s owner’s manual for detailed operating and safety instructions for all propane appliances. Cooktops: Range and Oven (if so equipped) For detailed operating and safety information, refer to the manufacturer’s user guide.
  • Page 131 Section 10: Appliances  Do not use aluminum foil on the electric range cooktop, as this material will damage the cooktop surface if it melts. Do not use aluminum foil under any circumstances on the electric range cooktop. Gas Drop-In Cooktops (if so equipped) Depending on your model, it may be equipped with either a 2 burner or 3 burner cooktop.
  • Page 132 Section 10: Appliances Gas BBQ Grill (if so equipped)  Be sure to read, understand and follow all information supplied with your recreation vehicle concerning the use of propane before operating the BBQ grill. The propane hose must be correctly connected before lighting the grill.
  • Page 133 Section 10: Appliances Rail Mount (if so equipped) Hang the grill bracket on the aluminum mount- ing strip located on the side of the recreation vehicle. Open the (2) folding arms on the bracket mak- ing sure they lock in position. Slide the grill onto the (2) arms against the stops.

  • Page 134: Range Hood (If So Equipped)

    Section 10: Appliances Range Hood (if so equipped) If your recreational vehicle is equipped with a range hood, it will be connected to an exterior vent. The vent has an inner flap with two snaps. This flap can be snapped shut when the vehicle is in motion, or during storage to keep insects, debris, snow, rain, etc.
  • Page 135 Section 10: Appliances  The ice maker (if so equipped) should be turned off and the ice tray emptied when power to your recreation vehicle has been shut off. With no power, the ice will melt and water may “pool” in the refrigerator door. When power is restored, the vibration may cause this water to run out of the door and on to the vehicle floor.
  • Page 136 Section 10: Appliances If you need to clean the condenser: Remove the base grille. Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area of the condenser. Replace the base grille when finished.
  • Page 137 Section 10: Appliances Place the “quick coupler handle in the OFF position and push back the sleeve. The valve handle must be OFF to make the connection. Insert the plug and release the sleeve Quick Connect Coupler Push the plug until the sleeve snaps for- ward, locking the plug into the socket.
  • Page 138 Section 10: Appliances  The grill requires proper ventilation. It is designed for RV outdoor use only. NEVER put lava rocks or charcoal or anything else on or under the grate. Grill is designed so it does not require those items. Serious injury or property damage can occur by placing foreign objects on the grate.

  • Page 139: Hdtv Antenna/Satellite System(S)

    Section 11: Electronics HDTV Antenna/Satellite System(s) HDTV Antenna (if so equipped) Your recreation vehicle is equipped with an exterior fixed height high definition TV antenna. This antenna rotates 360° and is capable of re- ceiving any over-the-air (OTA) high definition television signals being broadcast in your receiving area.
  • Page 140 Section 11: Electronics Notes: Maintenance Record Table of Contents...

  • Page 141: Cleaning The Interior

    Section 12: Interior Cleaning The Interior To keep the value of your recreation vehicle, perform regular maintenance using the proper materials and procedures. Using the wrong cleaner may result in damage to the surfaces in your vehicle. Check with the manufacturer’s information for the recommended cleaning agent.
  • Page 142 Section 12: Interior Mini Blinds: A simple dry rag may do the trick. If they are especially dirty, you can use cold or warm water to clean them; never use hot water.Fill a spray bottle with water and a tiny amount of soap. Then spray a lint-free towel with the mixture and use the towel to wipe down each slat.
  • Page 143 Section 12: Interior NOTE: Oil based soaps and cleaners are not recommended. No abrasive cleaners or alcohol cleansers should be used. If other cleaner solutions are used, we recommend trying a spot in an incon- spicuous area. ABS Plastics Dust and wipe clean with soft, damp cloth or chamois, wiping gently. Do not use gritty or abrasive particle soaps or scouring compound to clean ABS plastic.
  • Page 144 Section 12: Interior Cube Sofa The Cube Sofa functions similar to a residential futon. The slanted back pillows offer nu- merous options as a sofa, along with the ability to extend the cushions for additional sleeping space. Booth Dinette (if so equipped) The dinette is designed to seat up to four adults.

  • Page 145: Pantry Or Hutch (If So Equipped)

    Section 12: Interior Pantry or Hutch (if so equipped) Your recreation vehicle may have a pantry or hutch that you can use for storage. Make sure all items stored in the pantry or hutch are secured to prevent shifting during travel. This cabinetry has been designed to accommodate the normal camping items which may be bulky but not necessarily heavy.

  • Page 146: Murphy Bed (If So Equipped)

    Section 12: Interior Run cold water when pouring hot/boiling water into the sink. Solid surface sink maintenance Occasionally, clean the solid surface sink by filling one-quarter full with a 50/50 water/ bleach solution. Let soak for 15 minutes, and then wash sides and bottom of sink as solu- tion drains.
  • Page 147 Section 12: Interior  The slide out must be fully extended before putting the Murphy bed in the sleeping position. The Murphy bed must be in the stored position before the slide out can be moved to the in (travel) position. Failure to do so may result in injury or property damage This label has been installed in your recreation- al vehicle at the foot end of the Murphy bed.
  • Page 148 Section 12: Interior  Snap hooks (if present) must be attached to the steel rings on the sofa arms before using the bed. Failure to attach these snap hooks to the steel loops on the sofa can result in serious injury or property damage. MAKE SURE THE SAFETY STRAPS AT EACH SIDE OF THE FOOTBOARD ARE ATTACHED TO THE STEEL LOOPS ON THE SOFA ARMS BEFORE PUT-...

  • Page 149: Bed Storage

    Section 12: Interior  Keep hands and fingers away from the collapsing footboard and struts when pushing the bed back in to the storage position. Secure the two “D” bolts on each side of the bed. Flip the sofa back up into the seated position: ○...
  • Page 150 Section 12: Interior NOTE: Some types of bunk beds will not include a ladder.  Exercise extreme care when entering or exiting the bunk beds and using the ladder (if so equipped). Do not allow more than one person on the top bunk. Do not allow children under 6 years of age to use the upper bunk.

  • Page 151: Cleaning The Exterior

    Section 13: Exterior Cleaning the Exterior To protect your recreation vehicle’s exterior finish, wash it often and thoroughly. For recreation vehicles with painted exterior graphics: If desired you may wash and wax your vehicle 60 days after purchase. The exterior paint does need time to cure before any wax is applied to the exterior surface.
  • Page 152 Section 13: Exterior Drying the recreation vehicle is just as important as washing your vehicle. Tap and well water contain many chemicals that could water stain your vehicle’s finish. We suggest using a damp natural or synthetic chamois. There are other drying products such as lint-free micro-fiber towels that work just as well.

  • Page 153: E-Z Lube Or Super-Lube Axle (If So Equipped)

    Section 13: Exterior tone, polish the surface lightly with a fine polishing compound. Avoid limiting your polish- ing to the damaged surface only; polish a somewhat wider area, moving the polishing cloth in one direction. After polishing, flush the compound from the surface and apply a coat of wax to regain a beautiful luster.
  • Page 154 Section 13: Exterior Exterior Roof and Sidewall Vents Inspect the roof vents (including sealants) for cracks and keep them clean. Inspect the re- frigerator and holding tank vents for blockages from bird nests, spider webs, leaves, etc. All exterior access doors and vents need to be kept clean and free of obstructions (i.e., insect nests, mud daubers, etc.) while the appliances are in use.
  • Page 155 Section 13: Exterior Travel Trailers - Sealant Diagram Maintenance Record Table of Contents...
  • Page 156 Section 13: Exterior Notes: Maintenance Record Table of Contents...

  • Page 157: Section 14: Travel/Camping/Storage Checklists

    Section 14: Travel/Camping/Storage Checklists Travel Checklist Following is a preliminary list of items that need to be checked before leaving your home or campsite. This is a general list, which you may want to customize as you determine your own needs. Safety Make sure you follow all safety precautions noted in this owner’s manual and in any manufacturer’s operators manual when preparing to travel.
  • Page 158 Section 14: Travel/Camping/Storage Checklists Before leaving the campsite Check the area under the RV after overnight parking and look for water or other fluid leaks. If leaks are detected, find the cause and correct it immediately. Turn off propane tanks. Empty black and gray holding tanks, rinse as needed (if so equipped).
  • Page 159 Section 14: Travel/Camping/Storage Checklists Close the propane cylinder valve(s). We recommend using a propane cylinder cover, and to make sure the propane regulator is covered. If is equipped with a gas/ electric DSI range, light a range gas burner to consume any gas remaining in the lines.
  • Page 160 Section 14: Travel/Camping/Storage Checklists Notes: Maintenance Record Table of Contents...

  • Page 161: Featured Components Quick Reference Chart

    Your recreation vehicle may be equipped with some of the items listed below. This is a partial listing and it is not intended to cover all components. All information is the latest available at the time of publication. Jayco reserves the right to change any of the following information without notice.
  • Page 162 Section 15: Additional Information Thermostat Coleman Mach www.airxcel.com/coleman-mach Toilet Thetford Corp. www.thetford.com See manufacturers’ user guide Winegard Company www.winegard.com TV Antenna King Jack www.kingconnect.com Water Heater, Tank DSI Atwood Greenbrier www.atwoodmobile.com Girard Systems www.greenrvproducts.com Water Heater, Tankless Truma AquaGo www.truma.com Shurflo East www.shurflo.com Water Pump, 12V...

  • Page 163: Vehicle Maintenance Record

    Section 15: Additional Information Vehicle Maintenance Record Make: Model: Model Year: Vehicle Serial#: Service Performed Mileage Work Performed Notes Date Maintenance Record Table of Contents...
  • Page 164 Section 15: Additional Information Jayco Ownership Notification Fax Form To: (800) 825-7876 ATTENTION! Federal record keeping laws require that we maintain a file of owners of our product. Your cooperation in filling out this from will be appreciated. □ □...
  • Page 165 Section 15: Additional Information Notes: Maintenance Record Table of Contents...

Table of Contents