Jayco Eagle TT 2020 Owner's Manual
  1. Manuals
  2. Brands
  3. Jayco Manuals
  4. Motorhomes
  5. Eagle TT 2020
  6. Owner's manual

Jayco Eagle TT 2020 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2020
TT and HT Towables
Owner's Manual
0283661.2020

Advertisement

Table of Contents
loading

Related Manuals for Jayco Eagle TT 2020

Summary of Contents for Jayco Eagle TT 2020

  • Page 1 2020 TT and HT Towables Owner’s Manual 0283661.2020...
  • Page 3 44,683 people. We’re proud of our results, and we know those numbers show that a little initiative can go a long way. The Jayco EcoAdvantage is our way of making sure endless generations can enjoy the Great Outdoors.

  • Page 5: Table Of Contents

    Table of Contents Section 1: Warranty & Service Factory Tours Options and Equipment Dealer Responsibility Customer Relations To Contact Us About This Manual Warranty Packet Safety Alerts Reporting Safety Defects Customer Responsibility Change Of Address/Ownership Suggestions For Obtaining Service Obtaining Service For Separately Warranted Items Obtaining Service At Our Customer Service Facility Parts and Accessories Section 2: Occupant Safety...
  • Page 6 Table of Contents Section 4: Vehicle Operation Towing RV Brake System Electric Brakes Brake Controller (customer supplied) Travel Trailer Breakaway Switch Hydraulic Brakes (if so equipped) Disc Brakes (if so equipped) Towing Behind Your RV Entrance Door Step(s) Stowable Entrance Door Step (if so equipped) Entrance Door Rear Backup Camera Prep Campsite Hook-Up...
  • Page 7 Table of Contents Section 5: Slideout Systems Electric Slide Room(s) (if so equipped) General Slideout Operation Slideout Overlap-Outside General Slideout Troubleshooting Checklist Flush Floor Slideout Schwintek In-Wall Slideout System Error Codes Norco Slideout System Norco Slideout Manual Operation Power Gear Slideout System Fig.1 Slideout Controller Power Gear Slim Rack Slideout System Operating the Slideout...
  • Page 8 Table of Contents Section 7: Fuel & Propane System Exhaust Gas Fumes Propane Gas System Propane Gas Container Servicing or Filling “Shut off for re-fueling” Label “Do not fill to more than 80%” Label LP Gas Container Overfill Maintenance Propane Cylinder Recertification Hoses, Pipes, Tubes and Fittings Propane Regulator Propane Use and Safety...
  • Page 9 Table of Contents Water Heater Gas/Electric DSI Tank (Storage) Water Heater System (if so equipped) Anode Rod Replacement Chart Water Heater Bypass (if so equipped) Outside Shower (if so equipped) Faucets Bathroom Tub / Shower Black/Grey Water System and Tanks Black and Grey Tank Drains Black/Grey Tank Drain and Valves Macerator Pump System (if so equipped)
  • Page 10 Section 11: Electronics HDTV Antenna/Satellite System(s) HDTV Antenna (if so equipped) Antenna Power Supply (if so equipped) Antenna Power Supply Satellite (if so equipped) Section 12: Interior Cleaning The Interior Window Treatments Window Shades Cabinetry and Tables Interior Wall Panel Quik Panel Wall Panels (if so equipped) ABS Plastics Sofa and Dinette...
  • Page 11 WARNING: Read all instructions in this manual and component manufac- turer supplied information before using your RV. This manual has been provided by your recreational vehicle manufacturer for the sole pur- pose of providing instructions concerning the operation and maintenance of this recreational vehicle.

  • Page 13: Section 1: Warranty & Service

    Canada may differ to conform to Canadian Codes. Dealer Responsibility At the time of sale of the new recreation vehicle, your Jayco dealer is expected to: Deliver your recreation vehicle in the best condition possible. Your recreation ve- hicle must pass the dealer’s pre-delivery inspection (PDI), including all systems...
  • Page 14 (or any effect of the alterations) to any of the parts, components, systems or assemblies installed by Jayco. Jayco is not responsible for the safety or quality of design features, materials or workmanship of any alterations by such suppliers.

  • Page 15: To Contact Us

    Canada. In addition, the club offers a variety of local and regional activities throughout the year. By belonging to the Jayco Travel Club, you will find new ways to enjoy your RV and make friends all across the country.

  • Page 16: Warranty Packet

    Section 1: Warranty & Service Warranty Packet There are components that are excluded from the vehicle warranty, or are warranted sepa- rately by their own individual manufacturer’s limited warranty. The Warranty Packet con- tains these component manufacturer supplied manuals or information sheets, warranty cards and/or registrations.

  • Page 17: Reporting Safety Defects

    Section 1: Warranty & Service  Indicates a potentially hazardous situation that, if not avoided, may result in death or serious injury. Reporting Safety Defects In the United States: If you believe that your recreation vehicle has an alleged defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying our Cus- tomer Service Department.

  • Page 18: Customer Responsibility

    Section 1: Warranty & Service Customer Responsibility It is important you read and understand all instructions and precautions before operating the recreation vehicle. Even if you are an experienced RV’er we encourage you to thoroughly read this Owner’s Manual, as well as the information contained in your Warranty Packet and Chassis Guide (motorized only).

  • Page 19: Obtaining Service For Separately Warranted Items

    Section 1: Warranty & Service Please be aware that all service shops require notification of any issues with their repairs within a specified time limit. Make sure you are familiar with their repair policies. Obtaining Service For Separately Warranted Items Your selling dealer is responsible for servicing your recreational vehicle before delivery, and has an interest in your continued satisfaction.
  • Page 20 If a substantial defect in material or workmanship, attributable to Jayco, is found to exist and is reported to Jayco or an authorized servicing dealer during the appli- cable warranty period, it will be repaired or replaced, at Jayco’s option, without charge to the RV owner, in accordance with the terms, conditions and limitations of this limited warranty.
  • Page 21 RV is delivered to the first retail purchaser by an independent, authorized dealer of Jayco, or, if the dealer places the vehicle in service before retail sale, on the date the RV is first placed in such service.
  • Page 22 10 days of your discovery of the substantial defect; AND (2) you deliver the RV to Jayco or an authorized dealership at your cost and expense. If this primary remedy fails to successfully cure any substantial defect after a reasonable number of repair attempts, your sole and exclusive remedy shall be to have Jayco pay an independent service shop of your choice to perform repairs to the substantial defect.
  • Page 23 • vening acts not attributable to Jayco; damage caused by unregulated water pressure, tank over fill, or plumbing system modi- •...
  • Page 24 In addition, this warranty is not intended to extend to future performance, and nothing in this warranty, or any action of Jayco, or any agent of Jayco, shall be interpreted as an extension of the warranty period or this limitation period.
  • Page 25 ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE. ALL ACTIONS OF ANY KIND RELATING TO THE RV SHALL BE DECIDED BY A JUDGE RATHER THAN A JURY. JAYCO, INC. 903 S. Main Street * P.O. Box 460 * Middlebury, IN 46540 Telephone: 574-825-5861 or...
  • Page 26 Section 1: Warranty & Service Notes:...

  • Page 27: Secondary Means Of Escape (Exit Window)

    Section 2: Occupant Safety Secondary Means of Escape (Exit Window) Your recreation vehicle has been equipped with a window(s) that serves as a secondary means of escape. The window(s) will allow a quick exit from the vehicle during an emer- gency if access to the main entrance door is not available.

  • Page 28: Fire Safety

    Section 2: Occupant Safety Lever style latch Remove the screen by pulling the red tab (upper right arrow). Pull the lever out from the sash clamps. Swing the lever out so it is positioned straight out from the window. Push the lever (and window) out to open and exit the vehicle. Fire Safety If a fire does start, follow these basic safety rules: Call 911 and evacuate the vehicle immediately.

  • Page 29: Smoke Alarm

    Section 2: Occupant Safety  Do not check the pressure, test or practice using the fire extinguisher by squeezing the trigger, even briefly. The fire extinguisher is not rechargeable or refillable. Once used, it will gradually lose pressure and will not be fully charged for use in an emergency.

  • Page 30: Combination Carbon Monoxide /Propane Alarm

    Section 2: Occupant Safety alarms low battery warning (beep) starts to assure continued protection. When the battery is removed from the alarm, the battery flag will pop up; the alarm cannot be installed to the mounting bracket without a battery. To test, stand at arm’s length from the smoke alarm as the alarm horn is loud and may be harmful to your hear- ing.
  • Page 31 Section 2: Occupant Safety storage periods. This condition is not likely to occur except during storage situations when the inverter cannot restore the battery charge. If the battery cable is disconnected at the battery terminals, the combination alarm will not work. Be sure to read, understand and follow the owner’s information from the manufacturer of the combina- tion CO/propane alarm.
  • Page 32 Section 2: Occupant Safety Operate the RESET/SILENCE button. Call your emergency services (fire department or 911). Immediately move to fresh air (outdoors or by an open door or window). Do not re-enter the premises or move away from the open door or window until the emergency service responders have arrived, the premises have been aired out, and your alarm remains in its normal condition.

  • Page 33: Formaldehyde

    Section 2: Occupant Safety NOTE: Pressing the test button does not check the sensor opera- tion. Refer to the carbon monoxide/propane alarm manufacturers user’s manual provided with your recreation vehicle for additional information on testing the sensors. Repair or replace the combination carbon monoxide/propane alarm when the alarm no lon- ger functions.

  • Page 34: Cold Weather Usage

    Section 2: Occupant Safety Cold Weather Usage When used in freezing or below freezing temperatures, the precautions should be taken: Fresh water and drainage systems - preparations to avoid freeze-ups. Propane gas (if so equipped) and sufficient power is needed for protection from possible freeze-ups on the propane gas regulator.

  • Page 35: Vehicle Labels

    Section 3: Pre-Travel Information Vehicle Labels Decals and data plates used throughout the recreation vehicle aid in its safe and efficient op- eration; others give service instructions. Read all decals, data and instruction plates before operating your recreation vehicle. Any decal, data or instruction plate painted over, dam- aged or removed should be replaced.

  • Page 36: Occc Label (Yellow)

    Section 3: Pre-Travel Information OCCC Label (Occupant and Cargo Carrying Capacity The upper portion of this yellow label is feder- ally required and includes the maximum Oc- cupant and Cargo Carrying Capacity that may be placed in or on the trailer as it was manu- factured and weighed before leaving the factory.

  • Page 37: Loading Your Recreation Vehicle

    Section 3: Pre-Travel Information Loading Your Recreation Vehicle  Never load the RV in excess of the GAWR for either axle. Overload- ing your RV may result in adverse handling characteristics and dam- age to the RV. DO NOT EXCEED YOUR GVWR! This means you should weigh your RV as loaded for your normal travel to determine the actual weight.

  • Page 38: Rear Bumper

     Using an oversized or undersized hitch can cause damage to the RV frame. Jayco cannot be responsible for the tow vehicle suspension system. The fi- nal ball height after the tow vehicle/travel trailer combination is completely hooked up is a factor that must be considered. To avoid overloading your trailer axles and minimize possible handling difficulties, your trailer should be level when hooked to your tow vehicle.

  • Page 39: Travel Trailer Hitch Weight

    Section 3: Pre-Travel Information Travel Trailer Hitch Weight Maintain the proper tongue weight of the trailer. Stay within the target range of 10%-15% of the overall gross weight (travel trailer weight plus contents). Travel Trailer Hitch Height and Hitch Ball To determine the hitch height for your model, make sure that the trailer is level.

  • Page 40: Travel Trailer Weight Distributing System (Customer Supplied)

    Section 3: Pre-Travel Information Travel Trailer Weight Distributing System (customer supplied) This system provides a more stable tow vehicle/RV combination as it will spreads the weight evenly to distribute it to the tow vehicle front and rear axles and the trailer axle. Consult with your dealer for information on requirements and operation of this system.

  • Page 41: Wire Harness/Connector Plug

    Section 3: Pre-Travel Information Safety Chain Installation Wire Harness/Connector Plug A 7-way wire harness/connector plug is wired into your trailer to connect electrical power from the tow vehicle for travel. This supplies power to the RV brakes, taillights, clearance lights, turn signals, brake lights, etc. Wiring to operate your brakes must be the same size in both the tow vehicle and RV (the RV brake wiring is 12-gauge wire).

  • Page 42: Weighing Your Tow Vehicle And Rv

    Section 3: Pre-Travel Information NOTE: A 12V circuit tester is recommended to verify the trailer connections. Weighing Your Tow Vehicle and RV When the RV is fully loaded it should be weighed. The actual weight of the vehicle, all op- tions, liquids, the hitch weight, and your personal cargo is important for you to know so you do not exceed the GVWR.
  • Page 43 Section 3: Pre-Travel Information To determine the wheel position weight: Pull the RV onto the scale so only one tire is on the scale. Record the weight. Your RV must remain as level as possible on the scale (even though an axle or side is not physi- cally on the scale).
  • Page 44 Section 3: Pre-Travel Information Notes:...

  • Page 45: Section 4: Vehicle Operation

    Section 4: Vehicle Operation Towing  Your RV braking system is rated for operation at GVWR not GCWR. Whenever possible, do not travel with waste in the holding tanks. Liquid or debris in the holding tank(s) may affect the towing characteristics and may result in property damage or personal injury.

  • Page 46: Electric Brakes

    Section 4: Vehicle Operation Electric Brakes  Failure to maintain the brakes in proper working condition as specified in the operator’s manual supplied by the axle OEM will cause property damage, personal injury and possibly death. Consult with your dealer for assistance. The electric brakes are designed to work with the tow vehicle brakes.

  • Page 47: Disc Brakes (If So Equipped)

    If you do not have a Jayco factory installed hitch receiver, towing items behind your Jayco RV, or overloading the rear, will void the warranty and may result in: damage to the RV or add-on items, towing difficulties, property dam- age and/or personal injury.

  • Page 48: Entrance Door Step(S)

    Section 4: Vehicle Operation Entrance Door Step(s) Make sure your entrance step is fully extend- ed before exiting the vehicle, and retracted prior to towing. Lubricating the step mechanism Carefully clean the area around the pivot points (the rivets involved in the motion of the mecha- nism).

  • Page 49: Entrance Door

    Section 4: Vehicle Operation Step operation Open the entrance/screen door all the way. Twist the locking handle to release the steps from the locked position on the door frame (A). Lower the step assembly to the ground (B). Adjust the feet to stabilize the steps (C). Step storage Fold the handrail at the door out of the way or re- move the optional step handrail (if so equipped).

  • Page 50: Rear Backup Camera Prep

    Section 4: Vehicle Operation Rear Backup Camera Prep Your recreation vehicle has been pre-wired to allow for installation of a (customer supplied & customer installed) rear backup camera and a customer installed (or dealer installed) cam- era ON/OFF switch so the backup camera can be used as an observation/security camera. Depending on your RV model, a camera accessory power wire is pre-routed at the factory from the rear camera, to the bedroom or the command center panel inside the entrance door.

  • Page 51: (Bal)Leveling System (If So Equipped)

    Section 4: Vehicle Operation (BAL)Leveling System (if so equipped)  NEVER USE THIS SYSTEM FOR ANYTHING OTHER THAN ITS INTENDED USE. NEVER USE THE LEVELING SYSTEM AS A LIFT FOR CHANG- ING TIRES OR WORKING UNDER THE UNIT. KEEP PEOPLE, PETS AND OBSTRUCTIONS CLEAR OF THE UNIT BEFORE TURNING ON THE LEVELING SYSTEM AND WHILE OPERATING THE SYSTEM.
  • Page 52 Section 4: Vehicle Operation Buttons outlined in white are selectable. Buttons outlined in yellow are active. AUTOMATIC FUNCTIONS INCLUDE: • RV Detachment • Auto Leveling (front stabilizer jacks, and rear leveling legs) • RV Attachment • Tongue Jack Extend or Retract MANUAL FUNCTIONS INCLUDE: •...
  • Page 53 Section 4: Vehicle Operation The system will go through a series of moving the jacks and checking the unit for level. The display will read “Auto Level in Progress”. (G below) When the system successfully levels the unit the display will read “Auto Level Suc- cessful”...
  • Page 54 Section 4: Vehicle Operation The system will retract all stabilizer jacks and the rear leveling jacks, then extend or retract the tongue jack until proper connection height is achieved. Display will read “Auto Reconnect in Progress”. (M below) When the system has completed the “Auto Reconnect” function the display will read “Auto Reconnect Successful”...

  • Page 55: Tongue Jack Manual Override

    Section 4: Vehicle Operation MANUAL LEVELING JACK: Press MANUAL MODE. (U below) Use bubble level on the display to guide you. When the bubble is in the center of the circle the unit is level. Press and hold FRONT, REAR, LEFT or RIGHT and the jacks move as follows: •...

  • Page 56: Rear Leveling Jack Leg Override

    Section 4: Vehicle Operation Method 2 The tongue jack can also be overridden by removing the rubber plug to the right of the touch screen in the com- partment on top of the tongue jack. Use a ratchet wrench and insert a 3/8” square drive extension into the square hole located inside the plastic cover.

  • Page 57: Lci 3.0 Leveling System (If So Equipped)

    Section 4: Vehicle Operation LCI 3.0 Leveling System (if so equipped) The LCI Ground Control 3.0 is an electric 4 or 6 point automatic leveling control. The system utilizes one main control board and a separate waterproof remote level sensor to measure and manage level point, and can be operated from several user interface devices including: Auto Leveling Control Touch Pad - Mounted outside the RV within view of the hitch.

  • Page 58: Auto Leveling Touch Pad

    Section 4: Vehicle Operation NOTE: Pressing both the arrow buttons simultaneously turns on the touchpad. Touchpad will time out after 7 minutes of non-use. Auto Level Touchpad LED Indicator status OFF - Touch pad is locked Solid Green - Touch pad is active Blinking Green - Jacks are moving Solid Red - Low battery Blinking Red - Error...

  • Page 59: Onecontrol Touch Panel

    Section 4: Vehicle Operation NOTE: If the AUTO LEVEL sequence does not perform as described above, place the system in manual mode and test that the jacks operate correctly by using the OneControl touch panel inside the RV. OneControl Touch Panel Press the button at the bottom of the touch panel to power up the display.

  • Page 60: Onecontrol Touch Panel

    Section 4: Vehicle Operation Standard Mode and Menu Basic Jack operation Unhitching Instructions Auto Leveling Linc Remote Control Configuring the remote to sync with the OneControl Touch panel: Press the chrome button on the bottom of the remote to turn it on.

  • Page 61: Stabilizer Jacks

    Section 4: Vehicle Operation Stabilizer Jacks  DO NOT USE THE STABILIZER JACKS TO LEVEL THE RV. It is important to remember that the stabilizer jacks are to be used only for support while occupying and moving around the RV. They are not designed to support the weight of the RV.

  • Page 62: Emergency Stopping

    Section 4: Vehicle Operation Emergency Stopping Always carry road flares or reflective warning signs. Pull off the roadway as far as possible for emergency stopping. Turn ON your vehicle hazard warning flashers. If traveling at night, use three red warning indicators such as flares, reflectors or lanterns as required by the Uniform Vehicle Code and Model Traffic Ordinance as follows: Place the first warning indicator on the traffic side of the recreation vehicle, directed at the nearest approaching traffic.

  • Page 63: Wheel Lugs

    Section 4: Vehicle Operation Wheel Lugs After your first trip, check the wheel lug torque periodically for safety. Check the wheel lugs after winter storage, after a wheel removal, before starting a trip or following extensive braking: Use the correct star pattern sequence to attach the recreation vehicle wheels. Start all nuts by hand to prevent cross threading.

  • Page 64: Wheel Lug Nut Torque Values

    Section 4: Vehicle Operation Wheel Lug Nut Torque Values Prior to travel and after excessive braking, wheel lug nuts should be checked for torque. Torque readings must fall within the Final Torque Values in chart above. Torque specifications should be checked using a proper torque wrench. If the torque falls below the Final Torque Values, additional torque is required.

  • Page 65: Tires

    Section 4: Vehicle Operation Torque Wrench Usage Tools should be maintained, in good condition, and stored appropriately. • Avoid dropping or sliding a torque wrench. Dropping it can cause the instrument to lose reliable calibration. • Damaged tools must not be used and must be removed from service for evaluation and either reported and re-calibrated or replaced.
  • Page 66 Section 4: Vehicle Operation Tire Pressure  Failure to follow proper inflation guidelines may result in tire failure, which, under certain circumstances can cause loss of vehicle control or accidents that may result in property damage, bodily injury and/or death. You must follow the manufacturer’s inflation guidelines for maximum load capacity;...

  • Page 67: Changing A Tire

    Section 4: Vehicle Operation NOTE: Cold tire inflation pressure is defined as a tire that has not been used for three or more hours, or has been driven less than one mile. Tire inflation pressure of a hot tire may show an increase of as much as 6 psi over a cold tire.

  • Page 68: Spare Tire Carrier (If So Equipped)

    Section 4: Vehicle Operation If you experience a flat tire on your recreational vehicle while driving, gradually decrease your speed and move the recreational vehicle to a safe place on the side of the road. Keep the recreational vehicle attached to the tow vehicle. Block the tire on the opposite side of the recreational vehicle from the tire you are changing.

  • Page 69: Bumper Mount

    Section 4: Vehicle Operation Raising and lowering the hoist The crank handle to raise and lower the tire will be located (fastened to the sidewall) in a basement compartment of the recreational vehicle. Insert the crank handle into the crank access port located either in the center of the rear bumper, or on the sidewall of the RV.

  • Page 70: Setting Up Your Recreation Vehicle

    Section 4: Vehicle Operation To install the tire on the tire carrier Place the tire on the carrier with the top lug bolt in- serted into one of the holes in the tire rim and the bottom lug bolt in the center of the rim. Install the top lug nut.

  • Page 71: Awnings (If So Equipped)

    Section 4: Vehicle Operation Awnings (if so equipped)  Awnings must be closed (and locked if applicable) while the RV in transit.  The effects of wind and rain on an awning are unpredictable and can cause severe damage to the awning and/or the recreation vehicle. Retract the aw- ning if: If wind or extended periods of rain are expected If you leave the RV unattended for a length of time, to avoid unexpected...
  • Page 72 Section 4: Vehicle Operation Notes:...

  • Page 73: Section 5: Slideout Systems

    Section 5: Slideout Systems Electric Slide Room(s) (if so equipped) The mechanical components of the slide out are gear driven. Electric powered slideout room systems have a manual override to allow you to extend or retract the slideout room(s) in case of a power loss.

  • Page 74: Slideout Overlap-Outside

    Section 5: Slideout Systems Operating the switch after the room is fully extended or retracted may damage the switch and motor. After the slideout is extended, visually inspect the slideout and the surrounding area to make sure the slideout has extended properly and has adequate clearance from any outside obstruc- tions.
  • Page 75 Section 5: Slideout Systems NOTE: For long-term storage it is recommend the room be closed (retracted). Trouble shooting the flush floor slideout Refer to the general troubleshooting check list before proceeding. Electric Operation NOTE: Install transit bars (if so equipped) on the slideout room during storage and transportation.

  • Page 76: Schwintek In-Wall Slideout System

    Section 5: Slideout Systems Schwintek In-Wall Slideout System The in-wall slideout system requires no maintenance or adjustments. This system has two vertical columns with a drive motor located at the top of each column. The right and left NOTE: Do not operate the switch after the room is fully extended or retracted as damage can occur to the motor and/or switch.
  • Page 77 Section 5: Slideout Systems This slideout system requires very little maintenance. It contains a pre-lubed bearing that is lubricated when the room is moved in and out. Do not spray oil or grease on the rails while the room is extended. Trouble shooting the in-wall slideout system Checking Fuses: The in-wall slide requires a minimum 30-amp fuse.
  • Page 78 Section 5: Slideout Systems The red and green LED’s will flash indicating you are in override mode. Release the mode button. Using either a wall or command center panel switch, press and hold the switch toward the word IN or RETRACT until the unit comes in completely. This will allow you to get the recreation vehicle to a service center to have the slideout malfunction diagnosed.

  • Page 79: Error Codes

    Section 5: Slideout Systems Physically push/ pull the room back into the opening; keep both sides relatively even. The room must be travel locked to keep the room in place for road travel.  DO NOT MOVE THE RV UNLESS THE MOTORS ARE PLUGGED IN TO THE CONTROLLER AND THERE IS BATTERY POWER TO THE RV.

  • Page 80: Norco Slideout Manual Operation

    Section 5: Slideout Systems Norco Slideout Manual Operation Locate the included flexible shaft in your owner’s packet. Attach flexible shaft to the 1/4” hex fitting on the end of the motor. Attach 1/4” socket & ratchet, or drill to the other end, and turn in the proper direction to move the room.
  • Page 81 Section 5: Slideout Systems  When the motor brake is disengaged the slideout room WILL NOT lock into place and will not be sealed. When the room has been manually retracted, be sure to install transit bars (if so equipped) and return the motor brake lever to its normal engaged position in order to seal and lock the room into position.

  • Page 82: Power Gear Slim Rack Slideout System

    Section 5: Slideout Systems 10. Install the transit bars (if so equipped) to the slideout room and take the unit to an authorized dealer for service. Refer to the Power Gear® Electric Slideout Operation Manual for detailed operation, safety and troubleshooting information. Power Gear Slim Rack Slideout System The Power Gear®...
  • Page 83 Section 5: Slideout Systems Press and hold the OUT button (Fig 4). To retract, press and hold the IN button. There will be a slight delay before the room begins moving. The GREEN LED should be solid ON when room is in motion.
  • Page 84 Section 5: Slideout Systems Fault Codes Fault F a u l t Type Description Possible Cause Possible Solution Code -Stops have not been Steps need to be programmed Stops not Major -Stops were cleared by an authorized service programmed facility. -Stops were improp- erly set Run room in opposite direc-...
  • Page 85 Section 5: Slideout Systems Refer to the Power Gear® website www.powergearus.com for additional information. Override Modes: In the event of component failure or loss of system power, your slideout can be manually overridden and retracted for travel. NOTE: During the override procedure, the unit will exit this mode if the room has not been moved for two (2) minutes or if a fault is detected during room movement.
  • Page 86 Section 5: Slideout Systems Re-install the wall touchpad. Take the unit to an OEM certified dealer for repairs. Manually Retract Room with Ratchet and Socket If the power is lost to the slideout motor(s) or the override mode above will not work, the room may be manually retracted using a ratchet and socket attached to the end of the coupler (Fig 11).

  • Page 87: Power Gear Ram Slideout System

    Section 5: Slideout Systems Power Gear Ram Slideout System Typically used for Class C motorhomes. Manual Override Procedure The system has been equipped with 3/4” hex override couplers located on the drive compo- nent of the system. Due to the size and weight of some rooms, assistance may be needed to push the room in.
  • Page 88 Section 5: Slideout Systems will void your motor warranty. These photos will help you figure out how this works. The side-by-side photo (be- low) shows the spring lock lever and the brake lever. The spring lock lever is a thin metal arm with a slight bend at the end, which will hold the brake lever in the released position.

  • Page 89: The Electrical System

    Section 6: Electrical System The Electrical System The RV electrical system is comprised of two independent electrical systems. One operates off of 12-volt DC power and the other off of 120-volt 60hz AC power. All installations have been made in compliance with industry standards applicable on the date of manufacture. Because the electrical equipment and associated circuitry are engineered into a dedicated system specific to your RV, do not make unauthorized changes or add fixed appliances to it.

  • Page 90: Command Center

    Section 6: Electrical System Command Center The command center is typically located inside the entrance door or in the living area of the RV, and contains switches and controls for various electrical functions. Command center applications, configurations and components will vary by model. Command Center Panel or Command Center Panel with Switch Modules Items found on these panels may include:...

  • Page 91: Command Center Panel W/Switch Modules

    Section 6: Electrical System GFCI Receptacle There is a ground fault current interrupter (GFCI) engineered into the electrical system. It is designed to reduce the possible injury caused by electric shock. The GFCI will not protect against short circuits or circuit overloads. Test all GFCI receptacles monthly: Push in the GFCI “TEST”...
  • Page 92 Section 6: Electrical System NOTE: If a device does not appear on your touchscreen then that particular system is not installed on your RV. Awning Operation: Select the AWNING icon; the screen opens showing the awnings (Fig 5). If there are multiple awnings, there will be a selection for each awning at the left of the screen.

  • Page 93: 5-Way And 8-Way Power Remote (If So Equipped)

    Section 6: Electrical System DSI FLT - Direct Spark Ignition Fault (if so equipped): This light above the GAS water heater switch on the Command Center panel indicates a problem with the LP portion of the water heater. When the GAS switch is turned on, the light will blink quickly 3 times and the water heater will ignite.
  • Page 94 Section 6: Electrical System Reset the handheld remote PIN code Press the silver “HOME” button to turn the remote ON. Press and release the “HOME” button five times. The button with a picture of a key changes to the word “CONFIG”. Press the “CONFIG”...
  • Page 95 Section 6: Electrical System Important remote control operating information Never attempt to operate a slide-out, awning, stabilizer jack, landing gear, etc from the handheld remote and a corresponding switch (at the command center) at the same time. Doing so can blow one or more fuses on the multi-function receiver.

  • Page 96: Testing The Campsite Power Connection

    Section 6: Electrical System Batteries The remote is equipped with rechargeable batteries along with a charger. There are no user replaceable batteries. Testing the Campsite Power Connection The campsite 120-volt power receptacle(s) should always be tested for proper function- ality prior to plugging the recreation vehicle shore power cord into it. Campsite 120-volt power receptacles can be tested using a digital multimeter or a dedi- cated circuit analyzer.

  • Page 97: Connecting The Power Cord

    Section 6: Electrical System  Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. DO NOT plug the shore power cord into a campsite receptacle(s): That has reverse polarity With non-functioning ground circuits That shows outward signs of heat damage.

  • Page 98: Power Converter

    Section 6: Electrical System The shore line power cord should be unplugged when the recreation vehicle is left unattended. If something would happen to the electrical system, this may help limit potential damage. When you are ready to leave, reverse the power cord connection process. Use care to pre- vent damaging the power cord electrical connection pins when connecting or disconnecting the shore line power cord.

  • Page 99: Converter With Charge Wizard (If So Equipped)

    Section 6: Electrical System If the converter output voltage at the battery reads in the 0.0VDC range, or the battery is not charging, check for: An open inline fuse in the battery wire An open wire between the converter and the RV battery Loose ground connection Improper torques If the converter fuses and AC voltage are good, but the converter output still reads zero volts,...

  • Page 100: 12-Volt Dc System

    Section 6: Electrical System REVERSE BATTERY PROTECTION: Reverse polarity fuse(s) provide protection for the converter when a battery is used. If the battery is connected backwards to the fuse board a fuse will blow preventing damage to the converter. Four easily accessible fuses are located next to the wizard button.

  • Page 101: Auxiliary Battery (Customer Supplied)

    Section 6: Electrical System  Keep the protective dust cap on the 12-volt DC outlet when not in use to pre- vent ingestion of foreign material and potential short circuit conditions. Auxiliary Battery (customer supplied)  Do not store anything inside the battery compartment(s) or near the batteries that could touch the battery or battery cable terminals.

  • Page 102: Battery Disconnect Switches

    Section 6: Electrical System this from occurring, disconnect the 7-way trailer plug or install a battery isolator. When the tow vehicle engine is operating with the RV connected, the tow vehicle charging system will charge both batteries. Replacement and Maintenance Some equipment in your RV will draw small amounts of current even when turned OFF.

  • Page 103: Load Center

    Section 6: Electrical System Load Center The Load Center contains 12VDC fuses and 120VAC circuit breakers for almost all of the electrical appliances and circuits in the RV. The 120V main breaker may be located in this panel and will turn off all 120-volt power to the RV.

  • Page 104: Approximate Electrical Load Ratings

    Section 6: Electrical System  Replacement circuit breakers must be of the same voltage, amperage rating and type. Never use a higher rated replacement circuit breaker; doing so may cause a fire by overheating the RV wiring. Maintenance At the beginning of camping season, inspect the circuit breakers and replace as needed. Test by turning each circuit breaker “off”...

  • Page 105: 120-Volt (30 Amp) Ac System (If So Equipped)

    Section 6: Electrical System 120 VOLT SYSTEM Air Conditioner 18 AMPS Coffee Maker 6-12 AMPS Converter (each) 8 AMPS DVD System 3 AMPS Fireplace 12 AMPS Hair Dryer or Curling Iron 10-14 AMPS Microwave 12 AMPS Refrigerator 6 AMPS Satellite Receiver 2 AMPS 2-4 AMPS Vacuum Cleaner...

  • Page 106: 30-Amp Power Cord (If So Equipped)

    Section 6: Electrical System 30-amp Power Cord (if so equipped)  Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. Polarity indicators can be purchased in most electrical and hardware stores. Do not use any cheater plug, adapter or extension cord to reconfigure incoming AC power or break the continuity of the circuit connected to the grounding pin.

  • Page 107: 120-Volt (50 Amp) Ac System (If So Equipped)

    Section 6: Electrical System 120-Volt (50 AMP) AC System (if so equipped) The 50 amp 120-volt 60hz AC electrical system can be powered by an outside 120/240-volt 60hz utility service like those commonly found in campgrounds or by 120/240-volt 60hz generator power.

  • Page 108: Solar Prep (If So Equipped)

    Section 6: Electrical System The shore power cord is designed to continuously carry the 50-amp current flow required to power each leg of the electrical system. It also creates a critical ground connection between the vehicle electrical system and the campground shore power receptacle. Always test the external power source (i.e., the campsite power receptacle or electrical box) with a ground monitor before connecting your power cord to it.

  • Page 109: Section 7: Fuel & Propane System

    Section 7: Fuel & Propane System Exhaust Gas Fumes  Avoid inhaling exhaust gases as they contain carbon monoxide, which is a potentially toxic gas that is colorless and odorless. If you are in a recreation vehicle with either a nearby tow vehicle engine running or the generator (if so equipped) running there is a potential for exhaust fumes to filter back into the recreation vehicle To avoid breathing exhaust gases, follow these precautions:...

  • Page 110: Propane Gas Container

    Section 7: Fuel & Propane System recommended. Hand tighten the LP gas system valves only, do not use a wrench or pliers as over tightening may damage the valve seals and cause them to leak. NOTE: All propane lines have been checked with air pressure at the time of manufacture.

  • Page 111: Servicing Or Filling

    Section 7: Fuel & Propane System Be sure to securely re-install DOT cylinder(s) after they have been removed for filling or replacement. Always close the service valve and install a dust cap or plug when transporting or storing disconnected containers whether full or empty. ASME tanks are permanently mounted to the RV and are commonly used on RV mo- torhomes.

  • Page 112: Do Not Fill To More Than 80%" Label

    Section 7: Fuel & Propane System FILLED. This “shut off for re-fueling” label should be kept permanently affixed to your RV. The position of the propane container(s) and the hoses are critical to proper operation and propane flow. Follow these instructions to make sure your propane container(s) are con- nected properly.

  • Page 113: Propane Regulator

    Section 7: Fuel & Propane System It also has a left-handed thread, which means that it is turned clockwise to remove, and counter-clockwise to tighten. The P.O.L. fitting has been designed to help restrict the flow of LP gas in the event of a regulator failure or hose malfunction. Propane Regulator ...

  • Page 114: Propane Use And Safety

    Section 7: Fuel & Propane System Propane Use and Safety Propane is a colorless and odorless gas that, in the liq- uefied state, resembles water. An odorant (usually a sulfur compound) is added as a warning agent. If you smell propane within the vehicle, quickly and carefully perform the procedure listed on the propane system la- bel.

  • Page 115: Cooking With Propane Gas

    Section 7: Fuel & Propane System If you have double cylinders on your recreation vehicle, use only one at a time. Otherwise, the propane supply will be drawn equally from both cylinders until the supply has been total- ly exhausted. Using one cylinder until it is empty, then using the second cylinder will allow you to fill the empty cylinder at your convenience without running totally out of propane.

  • Page 116: Traveling With Propane

    Section 7: Fuel & Propane System Traveling With Propane NOTE: Some states prohibit propane appliances to be operated during travel, especially in underground tunnels. Make sure you know the laws for the areas where you travel. Use care when fueling your motor fuel tanks and/or propane containers.

  • Page 117: Main Supply Hose

    Section 7: Fuel & Propane System Secure the cylinder to the A-frame bracket using the bolts, nuts and washers provided. Double Cylinder Mounted On A-Frame (if so equipped) When a second cylinder is installed, a tee check valve is used to replace the 90° elbow at the top of the regulator and another 1/4”...
  • Page 118 Section 7: Fuel & Propane System Notes:...

  • Page 119: Section 8: Plumbing System

    Section 8: Plumbing System Plumbing System There are two different water systems in your recreation vehicle: The fresh water system consists of the fresh water holding tank, faucets and con- nections, water pump, outside shower assembly (if so equipped), water heater, tub/ shower, and water purification system (if so equipped).

  • Page 120: Fresh Water System

    Section 8: Plumbing System The LEDs on the panel indicate the following: C = Charge at 12.7 volts G = Good at 12.1 volts F = Fair at 11.6 volts L = Low at 6.0 volts The water pump switch (if so equipped) may be lo- cated on the monitor panel, the utility center or both.

  • Page 121: Water Pressure Regulator (Customer Supplied)

    Section 8: Plumbing System Water Pressure Regulator (customer supplied)  A water pressure regulator is recommended to prevent damage to the plumb- ing system or components. To prevent damage when using the city water connection, a 45 lb. (315 KPa) rated water pressure regulator is recommended. Excessive pressure from the water supply source may be encountered in some parks, espe- cially in mountain regions when using the fresh water inlet or black tank flush.

  • Page 122: Draining The Fresh Water System

    Section 8: Plumbing System The water pump switch should be in the OFF position when the RV is left unattended for any amount of time. If something would happen to the water system, this may help limit water damage to a smaller area. NOTE: In some models the water pump switch will be a black rocker switch located...

  • Page 123: Utility Center - 2 Valves (6 In 1)

    Section 8: Plumbing System Utility Center – 2 Valves (6 In 1) Your RV may be equipped with a small lockable en- closed docking station, which provides convenient ac- cess to certain plumbing system functions at one central location. The 6 in 1 utility center contains the following features: City water / tank fill valve Lighted white switch (switch itself acts as a light for the panel)
  • Page 124 Section 8: Plumbing System Fresh Water Connection Inlet The fresh water connection should be unplugged (i.e., the non-toxic drinking water hose disconnected) when the recreation vehicle is unattended for any amount of time. If something would happen to the water system, this may help limit water damage to a smaller area.
  • Page 125 Section 8: Plumbing System PRESSURE FILL WATER TANK: This setting will fill the water tank from a pressurized water source attached to the utility center panel. Set the blue CITY WATER / TANK FILL valve at the utility center to the TANK FILL position (horizontal) pointing to the left (as shown).
  • Page 126 Section 8: Plumbing System Place the clear suction hose into a container of sanitizer solution. Turn the pump switch ON and sanitizer will be drawn into fresh water tank. NOTE: Make sure you have sufficient 12V power and all drain valves are closed to create a siphon.

  • Page 127: Sanitizing The Plumbing System

    Section 8: Plumbing System Bypass Mode operation diverts the flow of water around the water heater keeping water out of the water heater. Hot water bypass valve (B) should point away from water heat- er and inline with the hot water output. Cold water bypass valve (A) should point away from the water heater and inline with the cold water supply.
  • Page 128 Section 8: Plumbing System Put the sanitizer solution in the fresh water tank. Place the end of the clear plastic tub- ing (found inside the basement access panel or at the water pump) into a container of chlorine solution. Turn the black valve (at the pump) so it is pointing to the clear siphon hose. Turn the white valve (at the pump) so it is pointing to the left toward the water tank line (as shown in Sanitize Tank &...
  • Page 129 Section 8: Plumbing System 16. Pressure fill the fresh water tank (refer to Step 9). Set the 2 valve water heater bypass to NORMAL allowing water into the water heater. Refer to the 2-Valve Water Heater Bypass section. 17. Water valves at the water pump should be in the NORMAL position to allow water into the RV lines.

  • Page 130: Winterizing (With Utility Center)

    Section 8: Plumbing System 12. Remove full system canister, insert the filter, and re-attach canister to the mount. For 2-Valve Bypass (if so equipped), set the water heater bypass valves to the NORMAL position. 13. Refill the fresh water system with clean water. Use pressure fill or siphon fill method explained previously.

  • Page 131: Air Pressure Method

    Section 8: Plumbing System The preferred method to winterize your recreation vehicle is by using RV antifreeze in the plumbing system. Air Pressure Method  If the recreation vehicle is going to be stored in a non-temperature controlled environment with a risk of temperatures reaching 32°F (0°C) or lower, the air pressure method is not adequate, winterizing with RV antifreeze must be used in the plumbing system.

  • Page 132: Winterizing With Antifreeze Method

    Section 8: Plumbing System NOTE: Filters should be replaced at the beginning of the camping season or if they have come into contact with contaminated water or antifreeze. Run the water pump until it is dry (approximately 15 to 20 seconds). Operating the pump longer than that with no water in it can damage the pump.
  • Page 133 Section 8: Plumbing System NOTE: Antifreeze should never enter the hot water heater or the water filter. Turn power to the water heater OFF (both electric and LP gas switches. Level the recreation vehicle and drain the fresh water plumbing system. See Draining the Fresh Water System.

  • Page 134: Nautilus P2.5 Uni-Dock Utility Center

    Section 8: Plumbing System Drain the hose by holding it at a sloped angle to remove excess water, return hose to the stored location. As an added safety measure, drain the macerator bypass valve. De-winterize the macerator system: Emptying the black tanks in the spring will flush antifreeze out of the macerator system.
  • Page 135 Section 8: Plumbing System Rinse the black tank to help control odors and prevent waste buildup Connect up to (3) coax lines with SAT, CABLE and AUX • SAT input is wired only to the wall plate for the satellite receiver. •...
  • Page 136 Section 8: Plumbing System “POWER FILL TANK” (Pressurized fresh water source) Connect the fresh water hose to the City water connection inlet on the utility center. Set the color coded valves to POWER FILL TANK setting: Green handle pointing left Blue handle pointing down Water heater bypass lever - NORMAL Connect the other end of the hose to a pressurized fresh water source...
  • Page 137 Section 8: Plumbing System “SANITIZE” (or Siphon Fill) the Fresh Water Tank via Pump NOTE: Refer to the Sanitizing Plumbing System section for complete instructions on how to sanitize the water lines. “WINTERIZE” (plumbing lines and fixtures via pump) NOTE: Refer to the Winterizing Plumbing System section for complete instructions on how to winterize the water lines and fixtures.
  • Page 138 Section 8: Plumbing System Prepare a chlorine solution using 1/4 cup of household bleach (sodium hypochlorite solution) to one gallon (3.785 liters) of water in a container. Prepare one gallon of solution for every 15 gallons of tank capacity. This will result in a residual chlorine concentration of 50 ppm in the water system.
  • Page 139 Section 8: Plumbing System 12. Set the valves to the DRY CAMPING setting. Green valve points down Blue valve points to the right Water Heater Bypass valve is still set to BYPASS. 13. Turn the water pump ON and sanitized water will flow into the water lines from the water tank (when a fixture is opened).
  • Page 140 Section 8: Plumbing System Run water through all faucets (hot and cold, including outside shower and outside kitchen) until chlorine smell is gone. Turn all faucets and outside shower off, turn pump OFF. Drain the fresh water system again. If the RV has the full system canister water filter, remove the canister, reinstall the filter, and reattach the canister.

  • Page 141: Winterizing The Plumbing System

    Section 8: Plumbing System Open faucets and check that the chlorine smell is gone. 10. Drain the system one more time. 11. Replace the water filter: Canister filter: Turn off water valves at the canister filter. Remove canister lid, put filter back into canister, and replace the canister lid.

  • Page 142: Winterize With Air Pressure

    Section 8: Plumbing System The preferred method to winterize your recreation vehicle is by using RV antifreeze in the plumbing system. It may be easier to winterize the RV with another person to assist you.  If the recreation vehicle is going to be stored in a non-temperature controlled environment with a risk of temperatures reaching 32°F (0°C) or lower, the plumbing system must be winterized with RV antifreeze.

  • Page 143: Winterize The Black Tank Flush

    Section 8: Plumbing System Your RV may have one of two types of filters: Full System Canister Filter: Remove the canister lid, take out the filter and then re- attach the lid on the empty canister. Cartridge Water Filter: Remove the cartridge filter and replace it with a bypass hose (supplied with your RV).

  • Page 144: Draining The Spray Port

    Section 8: Plumbing System NOTE: If the RV has a macerator system, you need to open the bypass valve for the macerator under the RV. This will allow the black tank to drain through the 4” sewer hose. Attach a garden hose to the TANK FLUSH inlet at the utility center. Attach the other end of the hose to a pressurized water source.
  • Page 145 Section 8: Plumbing System Turn water heater power OFF. The Gas and Electric switches inside the RV at the Command Center should be OFF. The water heater should never be drained when HOT or under pressure. Level the RV and drain the fresh water plumbing system. Refer to Draining the Fresh Water System.
  • Page 146 Section 8: Plumbing System 15. Wipe any RV antifreeze out of the sinks, shower (or tub), toilet, washing machine tub, and dishwasher tub with a soft, dry cloth. Contact your dealer if you require further assistance.  Water can accumulate in the flexible hose and dump connector of the macera- tor system.

  • Page 147: Water Heater

    Section 8: Plumbing System Water Heater  Hydrogen gas may result if you have not used the water heater for two weeks or more. HYDROGEN GAS IS EXTREMELY FLAMMA- BLE. To reduce the risk of injury under these conditions, open the hot water faucet for several minutes at the kitchen sink before you use any electrical appliance connected to the hot water system.

  • Page 148: Anode Rod Replacement Chart

    Section 8: Plumbing System NOTE: Each ignition cycle will have a 15 second purge before spark cycle if the system is a three try system. If lock-out occurs before the main burner lights, turn the water heater control switch to OFF, wait five seconds and turn the switch to the ON position. This will restart the ignition cycle.
  • Page 149 Section 8: Plumbing System To prevent a water leak when replacing the anode rod, a pipe thread sealant approved for potable water (such as Teflon tape) must be applied to the threads of the anode rod. Proper application of a thread sealant will not interfere with the anode’s function. High altitude deration Operation of the water heater at high altitudes may require derating.
  • Page 150 Section 8: Plumbing System Periodically, inspect the water heater vent for soot. Soot is a sign of incomplete combustion and must be corrected before operating the water heater. This is your visual warning that the water heater is operating in an unsafe manner. If soot is present, immediately shut the unit down and contact your dealer or a qualified service agency.

  • Page 151: Outside Shower (If So Equipped)

    Section 8: Plumbing System To reduce temperature: ○ Turn GMC dial “counter-clockwise”. ○ Increase hot water flow. ○ Gradually add cold water. To increase temperature: ○ Turn GMC dial “clockwise”. NOTE: Use caution not to increase the dial too much which could cause the hot water temperature to rise to the point the water heater “limits’...

  • Page 152: Faucets

    Section 8: Plumbing System To turn off the water, always close the hot/cold control (faucet) knobs. The lever on the shower head will not completely stop the flow of water; this is intentional to allow for drain- ing. After the water has been allowed to drain from the shower head, return it to the outside shower compartment.

  • Page 153: Black/Grey Water System And Tanks

    Section 8: Plumbing System The shower faucet includes a vacuum breaker for the shower. There are two purposes for this breaker: To prevent siphoning water through the hose from another fixture. To prevent water from being retained in the hose. The showerhead DOES NOT have a complete shut-off valve (the complete shut-off is at the faucet).
  • Page 154 Section 8: Plumbing System Vents Another important part of this system is the vent pipes and vents that release air from the grey and black water holding tanks. On most models the ex- terior vent cap is attached to the roof and must be kept clear of obstructions to perform as intended.

  • Page 155: Black And Grey Tank Drains

    Section 8: Plumbing System Black and Grey Tank Drains There are labels on the exterior of the recreation vehicle indicating the location of the grey and black tank drains (also called dump valves). Always drain the black water holding tank first so the following grey tank waste water can help rinse any solids or debris from the dump outlet and sewer hose.

  • Page 156: Macerator Pump System (If So Equipped)

    Section 8: Plumbing System Macerator Pump System (if so equipped) Your RV may be equipped with a macerator pump system used to discharge waste from the gray and black waste tank. The system has a 1-1/2 inch diameter flexible hose that runs from the pump (under the RV) and is stored in an exterior storage compartment.

  • Page 157: Black Tank Flush (If So Equipped)

    Section 8: Plumbing System The Macerator Bypass Valve is located underneath the external hose storage box. This by- pass will allow you to gravity dump the waste from the tanks straight down to a 3-inch sewer hose connection under the trailer, in the event there is a problem with the macerator motor. NOTE: The bypass valve also doubles as an emergency cutoff in the event of a problem with the flex hose or dump connector.

  • Page 158: Tank Heaters (If So Equipped)

    Section 8: Plumbing System With the water source turned ON, flush the black water holding tank until the water running out of the black tank drain valve is clear (not discolored or cloudy). Disconnect the garden hose and close the black tank drain valve. Fasten the sewer hose housing dust cap back on the tank flush inlet.

  • Page 159: Toilet

    Section 8: Plumbing System When the recreation vehicle is connected to city sewer and the gate valves are open. NOTE: Free draining is never recommended, especially in cold weather use. When ambient temperatures rise and remain above freezing. No maintenance on the heaters is required, only a periodic inspection for loose wires, dam- age, etc.

  • Page 160: Spray Port (If So Equipped)

    Section 8: Plumbing System Spray Port (if so equipped) Your RV may include a Spray Port on the exterior door side of the trailer. This Spray Port provides a way to rinse items off outside the RV or can be used to extinguish a campfire. There are no fau- cets to control (cold only) water flow.

  • Page 161: Air Conditioner

    Section 9: Heating & Cooling Air Conditioner The air conditioning system is controlled by a thermostat. Cooled air enters the RV through the grill. Make sure you have sufficient power available before operating the air conditioner. Do not operate the air conditioner without the return air filter. Operating the system without the filter allows the lint and dirt that is normally stopped by the filter to accumulate on the cooling coil of the air conditioner.

  • Page 162: Furnace

    Section 9: Heating & Cooling Furnace The furnace installed in your recreation vehicle is controlled by a 12-volt DC thermostat. Depending on your model, there may be up to two thermostats enabling you to control the temperature to your comfort level. The furnace requires both 12-volt power and propane gas for full operation.

  • Page 163: Microwave

    Section 10: Appliances Microwave  To prevent damage, remove the turntable from the microwave when traveling. Make sure you are connected to a 120-volt power source.  Never use the microwave cavity for storage. The microwave cavity should always be empty when not in use. For details on operation, cleaning and safety information, refer to the manufacturer’s user guide.

  • Page 164: Cooktops: Range And Oven (If So Equipped)

    Section 10: Appliances Cooking With Propane (if so equipped) See the Propane System Section for important safety instructions. Refer to the manufactur- er’s owner’s manual for detailed operating and safety instructions for all propane appliances. Cooktops: Range and Oven (if so equipped) For detailed operating and safety information, refer to the manufacturer’s user guide.

  • Page 165: Gas Drop-In Cooktops (If So Equipped)

    Section 10: Appliances  Do not use aluminum foil on the electric range cooktop, as this material will damage the cooktop surface if it melts. Do not use aluminum foil under any circumstances on the electric range cooktop. Gas Drop-In Cooktops (if so equipped) Depending on your model, it may be equipped with either a 2 burner or 3 burner cooktop.

  • Page 166: Gas Bbq Grill (If So Equipped)

    Section 10: Appliances Gas BBQ Grill (if so equipped)  Be sure to read, understand and follow all information supplied with your recreation vehicle concerning the use of propane before operating the BBQ grill. The propane hose must be correctly connected before lighting the grill.

  • Page 167: Attaching The "Quick Coupler" Connection

    Section 10: Appliances Rail Mount (if so equipped) Hang the grill bracket on the aluminum mount- ing strip located on the side of the recreation vehicle. Open the (2) folding arms on the bracket mak- ing sure they lock in position. Slide the grill onto the (2) arms against the stops.

  • Page 168: Range Hood (If So Equipped)

    Section 10: Appliances Range Hood (if so equipped) If your recreational vehicle is equipped with a range hood, it will be connected to an exterior vent. The vent has an inner flap with two snaps. This flap can be snapped shut when the vehicle is in motion, or during storage to keep insects, debris, snow, rain, etc.

  • Page 169: Cleaning The Interior

    Section 10: Appliances  The ice maker (if so equipped) should be turned off and the ice tray emptied when power to your recreation vehicle has been shut off. With no power, the ice will melt and water may “pool” in the refrigerator door. When power is restored, the vibration may cause this water to run out of the door and on to the vehicle floor.

  • Page 170: Cleaning The Exterior

    Section 10: Appliances If you need to clean the condenser: Remove the base grille. Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area of the condenser. Replace the base grille when finished.

  • Page 171: Vacuum Systems (If So Equipped)

    Section 10: Appliances Vacuum Systems (if so equipped) Depending on your model, one or both of the following vacuum systems may be in your recreation vehicle. Central Vacuum System The following is an overview of the central vacuum system operation. For detailed operat- ing and safety instructions, refer to the manufacturer’s user guide.

  • Page 172: Exterior Refrigerator

    Section 10: Appliances Outside kitchen access and locking functions may vary depending on your model. The following applies when using any outside kitchen configuration. Make sure all supports are securely in place before using the outside kitchen. Before using, make sure the propane connection is properly hooked up and secure. Do not leave the cooktop unattended while using.
  • Page 173 Section 10: Appliances NOTE: A drip pan is included with the grill. The drip pan MUST be used underneath the grill to catch hot grease and liquids dripping from the grill and to prevent injury. The drip pan attaches to tabs underneath the grill at each end.
  • Page 174 Section 10: Appliances Cleaning The Grill Make sure the grill is completely cool before cleaning. Use only non-abrasive cleaners or degreasers designed for use on stainless steel. Apply a stainless steel shine product to all external parts of your grill after cleaning. Clean the cooking grid with soap and water and a wire brush after each use.

  • Page 175: Section 11: Electronics

    Section 11: Electronics HDTV Antenna/Satellite System(s) HDTV Antenna (if so equipped) Your recreation vehicle is equipped with an exterior fixed height high definition TV antenna. This antenna rotates 360° and is capable of re- ceiving any over-the-air (OTA) high definition television signals being broadcast in your receiving area.
  • Page 176 Section 11: Electronics Notes:...

  • Page 177: Cleaning The Interior

    Section 12: Interior Cleaning The Interior To keep the value of your recreation vehicle, perform regular maintenance using the proper materials and procedures. Using the wrong cleaner may result in damage to the surfaces in your vehicle. Check with the manufacturer’s information for the recommended cleaning agent.

  • Page 178: Cabinetry And Tables

    Section 12: Interior Fill a spray bottle with water and a tiny amount of soap. Then spray a lint-free towel with the mixture and use the towel to wipe down each slat. While cleaning, try not to bend the slats. They can also be soaked in a bathtub to loosen up any debris so the slats can be wiped down easily.

  • Page 179: Abs Plastics

    Section 12: Interior NOTE: Oil based soaps and cleaners are not recommended. No abrasive cleaners or alcohol cleansers should be used. If other cleaner solutions are used, we recommend trying a spot in an incon- spicuous area. ABS Plastics Dust and wipe clean with soft, damp cloth or chamois, wiping gently. Do not use gritty or abrasive particle soaps or scouring compound to clean ABS plastic.

  • Page 180: Cube Sofa

    Section 12: Interior Cube Sofa The Cube Sofa functions similar to a residential futon. The slanted back pillows offer nu- merous options as a sofa, along with the ability to extend the cushions for additional sleeping space. Booth Dinette (if so equipped) The dinette is designed to seat up to four adults.

  • Page 181: Rolling Island Pantry (If So Equipped)

    Section 12: Interior Rolling Island Pantry (if so equipped) The rolling island pantry must be secured when traveling. Two se- curing rings are attached to the wall just inside the entrance door. The tie down strap runs through the rings and around the island to keep the doors closed and the pantry stationary while traveling.

  • Page 182: Flooring

    Section 12: Interior Laminate Countertops (if so equipped) Glass rings, food spills, water spots and smudges usually wipe off with a damp sponge. Stubborn stains can be removed with a general-purpose spray cleaner. Some stains can be removed by squeezing fresh lemon juice over the stain and allowing the juice to soak for ap- proximately forty-five minutes.

  • Page 183: Bed Storage

    Section 12: Interior Bed Storage Additional storage has been provided under the bed. To access the storage area, grasp the end ledge at the foot of the bed and lift carefully. The bed platform must be held when raised. It is recommended that two people retrieve stored items from under the bed so that one person may hold the platform, and the other to retrieve the stored items from under the bed.

  • Page 184: Bunk Beds (If So Equipped)

    Section 12: Interior Gas Struts (if so equipped) On certain models, the bed platform may be equipped with gas struts to assist with easy ac- cess to storage area. Grasp the end ledge at the foot of the bed and lift carefully. Two gas struts will hold the bed platform open allowing access to the storage area.
  • Page 185 Section 12: Interior  Exercise extreme care when entering or exiting the bunk beds and using the ladder (if so equipped). Do not allow more than one person on the top bunk. Do not allow children under 6 years of age to use the upper bunk. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
  • Page 186 Section 12: Interior Notes:...

  • Page 187: Cleaning The Exterior

    Section 13: Exterior Cleaning the Exterior To protect your recreation vehicle’s exterior finish, wash it often and thoroughly. For recreation vehicles with painted exterior graphics: If desired you may wash and wax your vehicle 60 days after purchase. The exterior paint does need time to cure before any wax is applied to the exterior surface.
  • Page 188 Section 13: Exterior Drying the recreation vehicle is just as important as washing your vehicle. Tap and well water contain many chemicals that could water stain your vehicle’s finish. We suggest using a damp natural or synthetic chamois. There are other drying products such as lint-free micro-fiber towels that work just as well.

  • Page 189: Frame

    Section 13: Exterior tone, polish the surface lightly with a fine polishing compound. Avoid limiting your polish- ing to the damaged surface only; polish a somewhat wider area, moving the polishing cloth in one direction. After polishing, flush the compound from the surface and apply a coat of wax to regain a beautiful luster.

  • Page 190: Exterior Roof And Sidewall Vents

    Section 13: Exterior Exterior Roof and Sidewall Vents Inspect the roof vents (including sealants) for cracks and keep them clean. Inspect the re- frigerator and holding tank vents for blockages from bird nests, spider webs, leaves, etc. All exterior access doors and vents need to be kept clean and free of obstructions (i.e., insect nests, mud daubers, etc.) while the appliances are in use.

  • Page 191: Sealants

    Section 13: Exterior  LADDER CAPACITY MAXIMUM 300 lbs (136 kg) DO NOT exceed the ladder maximum weight rating. The maximum rating includes the person’s weight PLUS weight of items carried. When climbing: • Always face the ladder. • Climb slowly with weight centered between side rails. •...

  • Page 192: Travel Trailers - Sealant Diagram

    Section 13: Exterior If you notice water inside the recreation vehicle, immediately have the dealer check for the source of the leak. Failure to correct the leak may result in serious damage to your recreation vehicle; this damage may not be warrantable. Although the following diagrams may not accurately reflect the exact model of your recre- ation vehicle, make sure you inspect all sealants as indicated in the text.

  • Page 193: Travel Checklist

    Section 14: Travel/Camping/Storage Checklists Travel Checklist Following is a preliminary list of items that need to be checked before leaving your home or campsite. This is a general list, which you may want to customize as you determine your own needs. Safety Make sure you follow all safety precautions noted in this owner’s manual and in any manufacturer’s operators manual when preparing to travel.

  • Page 194: Rv Storage

    Section 14: Travel/Camping/Storage Checklists Before leaving the campsite Check the area under the RV after overnight parking and look for water or other fluid leaks. If leaks are detected, find the cause and correct it immediately. Turn off propane tanks. Empty black and gray holding tanks, rinse as needed (if so equipped).
  • Page 195 Section 14: Travel/Camping/Storage Checklists Close the propane cylinder valve(s). We recommend using a propane cylinder cover, and to make sure the propane regulator is covered. If is equipped with a gas/ electric DSI range, light a range gas burner to consume any gas remaining in the lines.
  • Page 196 Section 14: Travel/Camping/Storage Checklists Notes:...

  • Page 197: Featured Components Quick Reference Chart

    Your recreation vehicle may be equipped with some of the items listed below. This is a partial listing and it is not intended to cover all components. All information is the latest available at the time of publication. Jayco reserves the right to change any of the following information without notice.
  • Page 198 Section 15: Additional Information Thermostat Coleman Mach www.airxcel.com/coleman-mach Toilet Thetford Corp. www.thetford.com See manufacturers’ user guide Winegard Company www.winegard.com TV Antenna King Jack www.kingconnect.com Water Heater, Tank DSI Atwood Greenbrier www.atwoodmobile.com Girard Systems www.greenrvproducts.com Water Heater, Tankless Truma AquaGo www.truma.com Shurflo East www.shurflo.com Water Pump, 12V...

  • Page 199: Vehicle Maintenance Record

    Section 15: Additional Information Vehicle Maintenance Record Make: Model: Model Year: Vehicle Serial#: Service Performed Mileage Work Performed Notes Date...

  • Page 200: Ownership Notification

    Section 15: Additional Information Jayco Ownership Notification Fax Form To: (800) 825-7876 ATTENTION! Federal record keeping laws require that we maintain a file of owners of our product. Your cooperation in filling out this from will be appreciated. □ □...
  • Page 201 Section 15: Additional Information Notes:...

This manual is also suitable for:

Eagle ht 2020

Table of Contents