1. Manuals
  2. Brands
  3. Jayco Manuals
  4. Motorhomes
  5. JAY FEATHER Towables 2020
  6. Owner's manual

Jayco JAY FEATHER Towables 2020 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2020
Towables
Owner's Manual
0195624.2020

Advertisement

Table of Contents
loading

Related Manuals for Jayco JAY FEATHER Towables 2020

Summary of Contents for Jayco JAY FEATHER Towables 2020

  • Page 1 2020 Towables Owner’s Manual 0195624.2020...
  • Page 3 44,683 people. We’re proud of our results, and we know those numbers show that a little initiative can go a long way. The Jayco EcoAdvantage is our way of making sure endless generations can enjoy the Great Outdoors.

  • Page 5: Table Of Contents

    Table of Contents Section 1: Warranty & Service Factory Tours Options and Equipment Dealer Responsibility Customer Relations To Contact Us About This Manual Warranty Packet Safety Alerts Reporting Safety Defects Customer Responsibility Change Of Address/Ownership Suggestions For Obtaining Service Obtaining Service For Separately Warranted Items Obtaining Service At Our Customer Service Facility Parts and Accessories Section 2: Occupant Safety...
  • Page 6 Table of Contents Section 4: Vehicle Operation Towing RV Brake System Electric Brakes Brake Controller (customer supplied) Travel Trailer Breakaway Switch Hydraulic Brakes (if so equipped) Disc Brakes (if so equipped) Towing Behind Your RV Entrance Door Step(s) Stowable Entrance Door Step (if so equipped) Entrance Door Rear Backup Camera Prep Campsite Hook-Up...
  • Page 7 Table of Contents Norco Slideout System Norco Slideout Manual Operation Power Gear Slideout System Fig.1 Slideout Controller Power Gear Slim Rack Slideout System Operating the Slideout Power Gear Ram Slideout System Section 6: Electrical System The Electrical System In Case Of An Electrical Fire Command Center Command Center Panel Command Center Panel W/Switch Modules...
  • Page 8 Table of Contents Propane Use and Safety Propane Leak Test Using the Propane System Propane System Label Cooking With Propane Gas Calculating Propane Gas Usage Cooking / Comfort Heating Label Traveling With Propane Installing Propane Cylinder(s) Refueling Warning Label Single Cylinder Main Supply Hose Double Cylinder Two Propane Cylinders...
  • Page 9 Table of Contents Section 9: Heating & Cooling Air Conditioner Roof Mount (if so equipped) Wall Mount (if so equipped) Heat Pump Operation (if so equipped) Power Roof Vent (if so equipped) Attic Fan Control Furnace Microwave Section 10: Appliances Cooking Safety In Case Of a Grease Fire Cooking with Propane (if so equipped)
  • Page 10 Table of Contents Pantry or Hutch (if so equipped) Countertops Laminate Countertops (if so equipped) Solid Surface Countertops (if so equipped) Flooring Carpet Vinyl Flooring Murphy Bed (if so equipped) Unfolding the Sofa Lowering the Murphy Bed Storing the Murphy Bed Bed Storage Prop Rod (if so equipped) Heated Bed Mats (if so equipped)
  • Page 11 WARNING: Read all instructions in this manual and component manufacturer supplied information before using your RV. This manual has been provided by your recreational vehicle manufacturer for the sole pur- pose of providing instructions concerning the operation and maintenance of this recreational vehicle.

  • Page 13: Section 1: Warranty & Service

    Canada may differ to conform to Canadian Codes. Dealer Responsibility At the time of sale of the new recreation vehicle, your Jayco dealer is expected to: Deliver your recreation vehicle in the best condition possible. Your recreation ve- hicle must pass the dealer’s pre-delivery inspection (PDI), including all systems...
  • Page 14 (or any effect of the alterations) to any of the parts, components, systems or assemblies installed by Jayco. Jayco is not responsible for the safety or quality of design features, materials or workmanship of any alterations by such suppliers.

  • Page 15: To Contact Us

    Canada. In addition, the club offers a variety of local and regional activities throughout the year. By belonging to the Jayco Travel Club, you will find new ways to enjoy your RV and make friends all across the country.

  • Page 16: Warranty Packet

    Section 1: Warranty & Service Warranty Packet There are components that are excluded from the vehicle warranty, or are warranted sepa- rately by their own individual manufacturer’s limited warranty. The Warranty Packet con- tains these component manufacturer supplied manuals or information sheets, warranty cards and/or registrations.

  • Page 17: Reporting Safety Defects

    Section 1: Warranty & Service  Indicates a potentially hazardous situation that, if not avoided, may result in death or serious injury. Reporting Safety Defects In the United States: If you believe that your recreation vehicle has an alleged defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying our Cus- tomer Service Department.

  • Page 18: Customer Responsibility

    Section 1: Warranty & Service Customer Responsibility It is important you read and understand all instructions and precautions before operating the recreation vehicle. Even if you are an experienced RV’er we encourage you to thoroughly read this Owner’s Manual, as well as the information contained in your Warranty Packet and Chassis Guide (motorized only).

  • Page 19: Obtaining Service For Separately Warranted Items

    Section 1: Warranty & Service Please be aware that all service shops require notification of any issues with their repairs within a specified time limit. Make sure you are familiar with their repair policies. Obtaining Service For Separately Warranted Items Your selling dealer is responsible for servicing your recreational vehicle before delivery, and has an interest in your continued satisfaction.
  • Page 20 Section 1: Warranty & Service...
  • Page 21 If a substantial defect in material or workmanship, attributable to Jayco, is found to exist and is reported to Jayco or an authorized servicing dealer during the appli- cable warranty period, it will be repaired or replaced, at Jayco’s option, without charge to the RV owner, in accordance with the terms, conditions and limitations of this limited warranty.
  • Page 22 RV is delivered to the first retail purchaser by an independent, authorized dealer of Jayco, or, if the dealer places the vehicle in service before retail sale, on the date the RV is first placed in such service.
  • Page 23 Section 1: Warranty & Service If you need assistance, you may contact Jayco, at 903 S. Main Street, P.O. Box 460, Middle- bury, Indiana 46540, Attn: Customer Service, (574) 825-5861, (800) 283-8267 or www. jayco.com. NOTE: Jayco does not control the scheduling of service work at the independent, authorized dealerships.
  • Page 24 • vening acts not attributable to Jayco; damage caused by unregulated water pressure, tank over fill, or plumbing system modi- •...
  • Page 25 In addition, this warranty is not intended to extend to future performance, and nothing in this warranty, or any action of Jayco, or any agent of Jayco, shall be interpreted as an extension of the warranty period or this limitation period.
  • Page 26 ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE. ALL ACTIONS OF ANY KIND RELATING TO THE RV SHALL BE DECIDED BY A JUDGE RATHER THAN A JURY. JAYCO, INC. 903 S. Main Street * P.O. Box 460 * Middlebury, IN 46540 Telephone: 574-825-5861 or...
  • Page 27 Section 1: Warranty & Service...
  • Page 28 Section 1: Warranty & Service...

  • Page 29: Secondary Means Of Escape (Exit Window)

    Section 2: Occupant Safety Secondary Means of Escape (Exit Window) Your recreation vehicle has been equipped with a window(s) that serves as a secondary means of escape. The window(s) will allow a quick exit from the vehicle during an emer- gency if access to the main entrance door is not available.

  • Page 30: Fire Safety

    Section 2: Occupant Safety Lever style latch Remove the screen by pulling the red tab (upper right arrow). Pull the lever out from the sash clamps. Swing the lever out so it is positioned straight out from the window. Push the lever (and window) out to open and exit the vehicle. Fire Safety If a fire does start, follow these basic safety rules: Call 911 and evacuate the vehicle immediately.

  • Page 31: Smoke Alarm

    Section 2: Occupant Safety  Do not check the pressure, test or practice using the fire extinguisher by squeezing the trigger, even briefly. The fire extinguisher is not rechargeable or refillable. Once used, it will gradually lose pressure and will not be fully charged for use in an emergency.

  • Page 32: Combination Carbon Monoxide /Propane Alarm

    Section 2: Occupant Safety alarms low battery warning (beep) starts to assure continued protection. When the battery is removed from the alarm, the battery flag will pop up; the alarm cannot be installed to the mounting bracket without a battery. To test, stand at arm’s length from the smoke alarm as the alarm horn is loud and may be harmful to your hear- ing.
  • Page 33 Section 2: Occupant Safety The alarm is directly wired to the 12-volt electrical system, with continuous power being supplied by the recreational vehicle batteries. There is no 9-volt battery power supply. As a result, the alarm is al- ways drawing a small amount of current from the recreation vehicle batteries.
  • Page 34 Section 2: Occupant Safety What you should do if the alarm sounds  Actuation of this detector indicates the presence of carbon monoxide which can kill you. Never turn the 12-volt battery disconnect control to the off position and disconnect the battery cable to silence an alarm. The alarm will auto- matically sense when the level of carbon monoxide in the air reaches below dangerous levels.

  • Page 35: Formaldehyde

    Section 2: Occupant Safety Testing the combination carbon monoxide/propane alarm  Test the alarm operation after the RV has been in storage, before each trip and at least once per week during use. The TEST/RESET button tests all ELECTRICAL functions of the alarm. The TEST/Mute switch is located on the front of the alarm.

  • Page 36: Cold Weather Usage

    Section 2: Occupant Safety  Continuous or permanent living in your recreation vehicle may affect your warranty coverage and may void the “Limited Warranty” applicable to your vehicle. Cold Weather Usage When used in freezing or below freezing temperatures, the precautions should be taken: Fresh water and drainage systems - preparations to avoid freeze-ups.

  • Page 37: Section 3: Pre-Travel Information

    Section 3: Pre-Travel Information Tow Vehicle If you plan to tow your recreation vehicle with a tow vehicle you already own, or if you plan to purchase a new one, make sure the Gross Vehicle Weight Rating (GVWR) or your recreation vehicle does not exceed your tow vehicles towing rating.

  • Page 38: Occc Label (Yellow)

    Section 3: Pre-Travel Information OCCC Label (Occupant and Cargo Carrying Capacity The upper portion of this yellow label is feder- ally required and includes the maximum Occu- pant & Cargo Carrying Capacity that may be placed in or on the trailer as it was manufac- tured and weighed before leaving the factory.

  • Page 39: Loading Your Recreation Vehicle

    Section 3: Pre-Travel Information Loading Your Recreation Vehicle  Never load the RV in excess of the GAWR for either axle. Overload- ing your RV may result in adverse handling characteristics and dam- age to the RV. DO NOT EXCEED YOUR GVWR! This means you should weigh your RV as loaded for your normal travel to determine the actual weight.

  • Page 40: Rear Bumper

     Using an oversized or undersized hitch can cause damage to the RV frame. Jayco cannot be responsible for the tow vehicle suspension system. The fi- nal ball height after the tow vehicle/travel trailer combination is completely hooked up is a factor that must be considered. To avoid overloading your trailer axles and minimize possible handling difficulties, your trailer should be level when hooked to your tow vehicle.

  • Page 41: Travel Trailer Hitch Weight

    Section 3: Pre-Travel Information Travel Trailer Hitch Weight Maintain the proper tongue weight of the trailer. Stay within the target range of 10%-15% of the overall gross weight (travel trailer weight plus contents) Travel Trailer Hitch Height & Hitch Ball To determine the hitch height for your model, make sure that the trailer is level.

  • Page 42: Travel Trailer Weight Distributing System (Customer Supplied)

    Section 3: Pre-Travel Information Travel Trailer Weight Distributing System (customer supplied) This system provides a more stable tow vehicle/RV combination as it will spreads the weight evenly to distribute it to the tow vehicle front and rear axles and the trailer axle. Consult with your dealer for information on requirements and operation of this system.

  • Page 43: Wire Harness/Connector Plug

    Section 3: Pre-Travel Information Safety Chain Installation Wire Harness/Connector Plug A 7-way wire harness/connector plug is wired into your trailer to connect electrical power from the tow vehicle for travel. This supplies power to the RV brakes, taillights, clearance lights, turn signals, brake lights, etc. Wiring to operate your brakes must be the same size in both the tow vehicle and RV (the RV brake wiring is 12-gauge wire).

  • Page 44: Weighing Your Tow Vehicle And Rv

    Section 3: Pre-Travel Information NOTE: A 12V circuit tester is recommended to verify the trailer connections. Weighing Your Tow Vehicle and RV When the RV is fully loaded it should be weighed. The actual weight of the vehicle, all op- tions, liquids, the hitch weight, and your personal cargo is important for you to know so you do not exceed the GVWR.
  • Page 45 Section 3: Pre-Travel Information To determine the wheel position weight: Pull the RV onto the scale so only one tire is on the scale. Record the weight. Your RV must remain as level as possible on the scale (even though an axle or side is not physi- cally on the scale).
  • Page 46 Section 3: Pre-Travel Information Notes:...

  • Page 47: Section 4: Vehicle Operation

    Section 4: Vehicle Operation Towing  Your RV braking system is rated for operation at GVWR not GCWR. Whenever possible, do not travel with waste in the holding tanks. Liquid or debris in the holding tank(s) may affect the towing characteristics and may result in property damage or personal injury.

  • Page 48: Electric Brakes

    Section 4: Vehicle Operation have not been affected. Never operate any vehicle if a difference in braking efficiency is noticeable. Electric Brakes  Failure to maintain the brakes in proper working condition as specified in the operator’s manual supplied by the axle OEM will cause property damage, personal injury and possibly death.

  • Page 49: Hydraulic Brakes (If So Equipped)

    If you do not have a Jayco factory installed hitch receiver, towing items behind your Jayco RV, or overloading the rear, will void the warranty and may result in: damage to the RV or add-on items, towing difficulties, property dam- age and/or personal injury.

  • Page 50: Entrance Door Step(S)

    Section 4: Vehicle Operation Entrance Door Step(s) Make sure your entrance step is fully extended before exiting the vehicle, and retracted prior to towing. Lubricating the step mechanism Carefully clean the area around the pivot points (the rivets involved in the motion of the mechanism).

  • Page 51: Entrance Door

    Section 4: Vehicle Operation Step operation Open the entrance/screen door all the way. Twist the locking handle to release the steps from the locked position on the door frame (A). Lower the step assembly to the ground (B). Adjust the feet to stabilize the steps (C). Step storage Fold the handrail at the door out of the way or re- move the optional step handrail (if so equipped).

  • Page 52: Rear Backup Camera Prep

    Section 4: Vehicle Operation Rear Backup Camera Prep Your recreation vehicle has been pre-wired to allow for installation of a (customer supplied & customer installed) rear backup camera and a customer installed (or dealer installed) cam- era ON/OFF switch so the backup camera can be used as an observation/security camera. Depending on your RV model, a camera accessory power wire is pre-routed at the factory from the rear camera, to the bedroom or the command center panel inside the entrance door.

  • Page 53: Manual Stabilizer Jacks (If So Equipped)

    Section 4: Vehicle Operation Each stabilizer jack can be individually adjusted to stabilize the RV for use. When setting up on soft ground, you may wish to place a wood pad or the equivalent under each stabilizer jack foot to help keep the jack from sinking into the ground. Manual Stabilizer Jacks (if so equipped) To lower each jack, insert the jack crank onto the applicable stabilizer jackshaft.

  • Page 54: Emergency Stopping

    Section 4: Vehicle Operation Emergency Stopping Always carry road flares or reflective warning signs. Pull off the roadway as far as possible for emergency stopping. Turn ON your vehicle hazard warning flashers. If traveling at night, use three red warning indicators such as flares, reflectors or lanterns as required by the Uniform Vehicle Code and Model Traffic Ordinance as follows: Place the first warning indicator on the traffic side of the recreation vehicle, directed at the nearest approaching traffic.

  • Page 55: Wheel Lug Nut Diagrams

    Section 4: Vehicle Operation NOTE: The proper method of tightening wheel lug nuts is with a properly calibrated torque wrench and socket, not with an impact wrench or by hand. Do not use a 4-way lug wrench or any other type of wrench that does not measure the actual pressure applied to the lug nut.

  • Page 56: Wheel Lug Nut Torque Values

    Section 4: Vehicle Operation Wheel Lug Nut Torque Values Prior to travel and after excessive braking, wheel lug nuts should be checked for torque. Torque readings must fall within the Final Torque Values in chart above. Torque specifications should be checked using a proper torque wrench. If the torque falls below the Final Torque Values, additional torque is required.

  • Page 57: Tires

    Section 4: Vehicle Operation Torque Wrench Usage Tools should be maintained, in good condition, and stored appropriately. • Avoid dropping or sliding a torque wrench. Dropping it can cause the instrument to lose reliable calibration. • Damaged tools must not be used and must be removed from service for evaluation and either reported and re-calibrated or replaced.
  • Page 58 Section 4: Vehicle Operation  Tire wear should be checked frequently. Once a wear pattern becomes firmly established in a tire it is difficult to stop, even if the underlying cause is cor- rected. Tire Pressure  Failure to follow proper inflation guidelines may result in tire failure, which, under certain circumstances can cause loss of vehicle control or accidents that may result in property damage, bodily injury and/or death.

  • Page 59: Changing A Tire

    Section 4: Vehicle Operation Changing A Tire  Do not use the stabilizer jacks to support the recreational vehicle while under the vehicle or changing tires. The stabilizer jacks are designed as a stabilizing system only. Do not use the stabilizer jacks as a jack or in conjunction with a jack.

  • Page 60: Bracket Mount Travel Position

    Section 4: Vehicle Operation Depending on your model, the spare tire may have (side or bottom) brackets or it will be mounted against the underside of the recreation vehicle (flush mount) to give it stability in travel. Hoist Mount Travel Position Bracket Mount Travel Position NOTE: If your spare tire is a flush mount application, it must make contact with the underside of the recreational vehicle to insure...

  • Page 61: Bumper Mount

    Section 4: Vehicle Operation Bumper Mount The spare tire bracket can be released and extended down to access a storage compartment at the rear of the trailer without removing the tire. To extend the tire down Remove the cotter key from the pin holding the tire car- rier in place.

  • Page 62: Caring For The Tent

    Section 4: Vehicle Operation 15. Drive away. 16. Adjust the fifth-wheel height for proper front to back leveling of the RV. Caring For The Tent  It is very important to “season” your new tent. If you do not follow this proce- dure, you may experience some water seepage during the first few exposures to rain.

  • Page 63: Tent Maintenance

    Section 4: Vehicle Operation Tent Maintenance  Do not use any cleaner which contains abrasives, solvents, citrus or chlorine bleach. Damage to the fabric will result. Exterior or Vinyl Side For minor stains, dirt, etc., the vinyl or outside of the material can be cleaned with mild liq- uid detergent and water, using a sponge or soft cloth.
  • Page 64 Section 4: Vehicle Operation The front bed is equipped with canvas straps to hold the bunk mats in place while not in use. Unhook the canvas straps by using the clips at the top edge. Unlock and release the exterior locks that hold the bed board in place.
  • Page 65 Section 4: Vehicle Operation Remove the bed bow brace from the ceiling by pushing in on the exposed push-button and pulling down. Pull the bed bow towards you and remove the “claw” connector from the curved win- dow bow. Set the bed bow brace aside. From the exterior, lift the bottom of the tent up exposing the bed platform.

  • Page 66: Awnings (If So Equipped)

    Section 4: Vehicle Operation  Heated bed mats (if so equipped) should not be stored between the wall and bed platform. Storing them in a tight space or in a twist or bind may result in damage to the heating elements. See Section 12; Heated Bed Mats for more information.

  • Page 67: Power Awnings (If So Equipped)

    Section 4: Vehicle Operation Power Awnings (if so equipped)  Awnings must be closed (and locked if applicable) while the RV is in transit.  The effects of wind and rain on an awning are unpredictable and can cause severe damage to the awning and/or the recreation vehicle. If wind or extended periods of rain are expected, retract the awning.

  • Page 68: Carefree® Travel'r Awnings (If So Equipped)

    Section 4: Vehicle Operation Hold on to the awning arm to keep it steady while adjusting the pitch. Press in the pitch adjustment pins located on the scissor arm. Applying LIGHT pres- sure on the arm will decrease the force required to press the pitch adjustment pins. Slide the scissor arm to the desired set hole –...
  • Page 69 Section 4: Vehicle Operation Press the power switch to ON. The Direct Response system is activated and man- ual controls are active. All functions are disabled if the switch is off. Press and hold the EXTEND switch to open the awning. Press and release the RETRACT switch.
  • Page 70 Section 4: Vehicle Operation Notes:...

  • Page 71: Electric Slide Room(S) (If So Equipped)

    Section 5: Slideout Systems Electric Slide Room(s) (if so equipped) The mechanical components of the slide out are gear driven. Electric powered slideout room systems have a manual override to allow you to extend or retract the slideout room(s) in case of a power loss.

  • Page 72: General Slideout Troubleshooting Checklist

    Section 5: Slideout Systems Operating the switch after the room is fully extended or retracted may damage the switch and motor. After the slideout is extended, visually inspect the slideout and the surrounding area to make sure the slideout has extended properly and has adequate clearance from any outside obstruc- tions.
  • Page 73 Section 5: Slideout Systems NOTE: For long-term storage it is recommend the room be closed (retracted). Trouble shooting the flush floor slideout Refer to the general troubleshooting check list before proceeding. Electric Operation NOTE: Install transit bars (if so equipped) on the slideout room during storage and transportation.

  • Page 74: Schwintek In-Wall Slideout System

    Section 5: Slideout Systems Schwintek In-Wall Slideout System The in-wall slideout system requires no maintenance or adjustments. This system has two vertical columns with a drive motor located at the top of each column. The right and left motors are synchronized by a circuit board. Schwintek slideouts are typically used on both towables and motorhomes.
  • Page 75 Section 5: Slideout Systems This slideout system requires very little maintenance. It contains a pre-lubed bearing that is lubricated when the room is moved in and out. Do not spray oil or grease on the rails while the room is extended. Trouble shooting the in-wall slideout system Checking Fuses: The in-wall slide requires a minimum 30-amp fuse.
  • Page 76 Section 5: Slideout Systems The red and green LED’s will flash indicating you are in override mode. Release the mode button. Using either a wall or command center panel switch, press and hold the switch toward the word IN or RETRACT until the unit comes in completely. This will allow you to get the recreation vehicle to a service center to have the slideout malfunction diagnosed.

  • Page 77: Error Codes

    Section 5: Slideout Systems Physically push/ pull the room back into the opening; keep both sides relatively even. The room must be travel locked to keep the room in place for road travel.  DO NOT MOVE THE RV UNLESS THE MOTORS ARE PLUGGED IN TO THE CONTROLLER AND THERE IS BATTERY POWER TO THE RV.

  • Page 78: Norco Slideout Manual Operation

    Section 5: Slideout Systems Norco Slideout Manual Operation Locate the included flexible shaft in your own- er’s packet. Attach flexible shaft to the 1/4” hex fitting on the end of the motor. Attach 1/4” socket & ratchet, or drill to the other end, and turn in the proper direction to move the room.
  • Page 79 Section 5: Slideout Systems  When the motor brake is disengaged the slideout room WILL NOT lock into place and will not be sealed. When the room has been manually retracted, be sure to install transit bars (if so equipped) and return the motor brake lever to its normal engaged position in order to seal and lock the room into position.

  • Page 80: Power Gear Slim Rack Slideout System

    Section 5: Slideout Systems 10. Install the transit bars (if so equipped) to the slideout room and take the unit to an authorized dealer for service. Refer to the Power Gear® Electric Slideout Operation Manual for detailed operation, safety and troubleshooting information. Power Gear Slim Rack Slideout System The Power Gear®...
  • Page 81 Section 5: Slideout Systems Release the OUT button when the room is fully extended or the IN button when fully retracted, and stops moving. Turn OFF the on/off switch or key. Fault Diagnostics / Troubleshooting The control has the ability to detect and display several faults. When a fault is detected, room movement stops and two different LEDs will flash in a pattern.
  • Page 82 Section 5: Slideout Systems Check 2-pin power connector Supply voltage to con- at control box. If the voltage Minor trol box is 17 0 V DC is 17. VDC or higher, contact or greater O.E.M for power and ground supplies -Set parking brake (if ap- -Parking brake not set plicable)
  • Page 83 Section 5: Slideout Systems Emergency Retract Mode Use this procedure when there is NO loss of power or electrical problem with the system. Remove the touchpad (Fig 4) from the wall. Prior to clearing the MAJOR fault, record the number of RED and GREEN flashes observed on the touchpad (Fig 6).
  • Page 84 Section 5: Slideout Systems NOTE: One person on each side of the room with a ratchet and socket will expedite the process. Room moves ¼ inch for every 30 to 40 degree turn of the wrench. Secure the room in place by either: Re-installing the motors (making sure the end of the retaining screw is re-hooked to the motor spring clip (Fig 10A).

  • Page 85: Power Gear Ram Slideout System

    Section 5: Slideout Systems Power Gear Ram Slideout System Typically used for Class C motorhomes. Manual Override Procedure The system has been equipped with 3/4” hex override couplers located on the drive component of the system. Due to the size and weight of some rooms, assistance may be needed to push the room in.
  • Page 86 Section 5: Slideout Systems 12. Return the brake release lever back to the “engaged” position (parallel to the spring lock lever). Pressing the bent end of the spring lock lever will allow the brake le- ver to be moved. 13. Plug the motor connector back in again. 14.

  • Page 87: The Electrical System

    Section 6: Electrical System The Electrical System The RV electrical system is comprised of two independent electrical systems. One operates off of 12-volt DC power and the other off of 120-volt 60hz AC power. All installations have been made in compliance with industry standards applicable on the date of manufacture. Because the electrical equipment and associated circuitry are engineered into a dedicated system specific to your RV, do not make unauthorized changes or add fixed appliances to it.

  • Page 88: Command Center

    Section 6: Electrical System Command Center The command center is typically located inside the entrance door or in the living area of the RV, and contains switches and controls for various electrical functions. Command center applications, con- figurations and components will vary by model. Command Center Panel or Command Center Panel with Switch Modules Items found on these panels may include:...

  • Page 89: Gfci Receptacle

    Section 6: Electrical System GFCI Receptacle There is a ground fault current interrupter (GFCI) engineered into the electrical system. It is designed to reduce the possible injury caused by electric shock. The GFCI will not protect against short circuits or circuit overloads. Test all GFCI receptacles monthly: Push in the GFCI “TEST”...
  • Page 90 Section 6: Electrical System Press “SAVE” (Fig 6-A). 10. Press “HOME” button. When the keypad appears on the screen, enter the new 4-digit PIN (Fig 7). Operating the handheld remote The menu screen will show sets of (4) functions (Fig 8). Select a function or press “NEXT”...
  • Page 91 Section 6: Electrical System remote will enter “Sleep Mode” after 60 seconds of inactivity. Press the “HOME” button to wake it up. Awning Operation: Select the AWNING 1 switch; the screen opens showing the awning function screen. If there are multiple awnings, there will be a selection for each aw- ning at the left of the screen.

  • Page 92: Testing The Campsite Power Connection

    Section 6: Electrical System Batteries The remote is equipped with rechargeable batteries along with a charger. There are no user replaceable batteries. Testing the Campsite Power Connection The campsite 120-volt power receptacle(s) should always be tested for proper function- ality prior to plugging the recreation vehicle shore power cord into it. Campsite 120-volt power receptacles can be tested using a digital multimeter or a dedi- cated circuit analyzer.

  • Page 93: Connecting The Power Cord

    Section 6: Electrical System Connecting the Power Cord Always test the external power source (i.e., the campsite power receptacle or electrical box) with a ground monitor before connecting your power cord to it. If the ground monitor indi- cates ‘reverse polarity’ or an ‘open ground’ DO NOT connect the power cord. To help prevent power surges from damaging the connected loads, please follow these in- structions when hooking up to the external power source: Turn “off”...

  • Page 94: Converter With Charge Wizard (If So Equipped)

    Section 6: Electrical System  It is important that the fluid level of any connected batteries be checked on a regular basis. All batteries will “gas” and lose some fluid when continuously connected to any charging source (does not apply to “gel-cell” batteries). Before checking for converter output voltage, the battery cables must be disconnected at the battery.

  • Page 95: 12-Volt Dc System

    Section 6: Electrical System BOOST MODE: Green LED is on solid. Output voltage is 14.4VDC to rapidly charge the battery up to 90% of full charge. STORAGE MODE: Green LED flashes every 6-8 seconds. Output voltage has been reduced to 13.2VDC; the RV bat- tery is fully charged and converter is maintaining the charge.

  • Page 96: Auxiliary Battery (Customer Supplied)

    Section 6: Electrical System The fuse panel label should be kept permanently affixed to your recreation vehicle. Fuses will not offer complete protection of the electrical system in the event of a power surge or spike. 12-Volt DC Outlet There may be one or more 12-volt DC power outlets in your recreation vehicle. When the 12-volt DC outlet is used as a power source for an electric appliance, make sure the appli- ance operates on 12-volt DC power and that it consumes less than 60 watts (5 amps) of power.

  • Page 97: Replacement And Maintenance

    Section 6: Electrical System (12.0 + 3.0) 15.0 amps per hour. This does not include any 12-volt lights, or any other 12- volt component. If the furnace and refrigerator in this example operated constantly, a 75 amp-hour battery would become fully discharged in 5 hours. The auxiliary battery should be installed in parallel with the battery in your tow vehicle.

  • Page 98: Load Center

    Section 6: Electrical System Load Center The Load Center contains 12VDC fuses and 120VAC circuit breakers for almost all of the electrical appliances and circuits in the RV. The 120V main breaker may be located in this panel and will turn off all 120-volt power to the RV.
  • Page 99 Section 6: Electrical System  Replacement circuit breakers must be of the same voltage, amperage rating and type. Never use a higher rated replacement circuit breaker; doing so may cause a fire by overheating the RV wiring. Maintenance At the beginning of camping season, inspect the circuit breakers and replace as needed. Test by turning each circuit breaker “off”...

  • Page 100: Approximate Electrical Load Ratings

    Section 6: Electrical System Approximate Electrical Load Ratings 12 VOLT SYSTEM Exterior Entertainment Center 5-7 AMPS 1.5 AMPS Furnace 12.0 AMPS Generator Start 95.0 AMPS* Illuminated Switch .125 AMP Inverter variable Leveling System 95.0 AMPS* LP Detector .125 AMP Light; Halogen 1.7 AMPS Light;...

  • Page 101: 120-Volt (30 Amp) Ac System (If So Equipped)

    Section 6: Electrical System 120-Volt (30 AMP) AC System (if so equipped) The 30 amp 120-volt 60hz AC electrical system.is designed to operate on 1 leg of 120-volt power at a maximum current flow of 30 amperes. Exposure to voltages higher or lower than a nominal 120-volts will damage or shorten the service life of the electrical system and appliances.

  • Page 102: 120-Volt (50 Amp) Ac System (If So Equipped)

    Section 6: Electrical System power each leg of the electrical system. It also creates a critical ground connection between the vehicle electrical system and the campground shore power receptacle. Always test the external power source (i.e., the campsite power receptacle or electrical box) with a ground monitor before connecting your power cord to it.
  • Page 103 Section 6: Electrical System 50-AMP Power Cord (if so equipped)  Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. Polarity indicators can be purchased in most electrical and hardware stores. Do not use any cheater plug, adapter or extension cord to reconfigure incoming AC power or break the continuity of the circuit connected to the grounding pin.

  • Page 104: Solar Prep (If So Equipped)

    Section 6: Electrical System Solar Prep (if so equipped) Your recreation vehicle may be wired with a (exterior) plug in that will allow the batteries to be trickle charged using a free standing solar panel. In most models, the solar panel kit is a customer pur- chased and installed option.

  • Page 105: Section 7: Fuel & Propane System

    Section 7: Fuel & Propane System Exhaust Gas Fumes  Avoid inhaling exhaust gases as they contain carbon monoxide, which is a potentially toxic gas that is colorless and odorless. If you are in a recreation vehicle with either a nearby tow vehicle engine running or the generator (if so equipped) running there is a potential for exhaust fumes to filter back into the recreation vehicle.

  • Page 106: Propane Gas Container

    Section 7: Fuel & Propane System Continued periodic checks of the propane system at 5,000 miles of travel (or at least once a year), by a qualified propane service representative as part of your normal maintenance is recommended. Hand tighten the LP gas system valves only, do not use a wrench or pliers as over tightening may damage the valve seals and cause them to leak.

  • Page 107: Servicing Or Filling

    Section 7: Fuel & Propane System position indicated. Be sure to securely re-install DOT cylinder(s) after they have been removed for filling or replacement. Always close the service valve and install a dust cap or plug when transporting or storing disconnected containers whether full or empty. ASME tanks are permanently mounted to the RV and are commonly used on RV mo- torhomes.

  • Page 108: Do Not Fill To More Than 80%" Label

    Section 7: Fuel & Propane System purged for best performance and must NEVER BE OVERFILLED. This “shut off for re- fueling” label should be kept permanently affixed to your RV. The position of the propane container(s) and the hoses are critical to proper operation and propane flow.

  • Page 109: Propane Regulator

    Section 7: Fuel & Propane System It also has a left-handed thread, which means that it is turned clockwise to remove, and counter-clockwise to tighten. The P.O.L. fitting has been designed to help restrict the flow of LP gas in the event of a regulator failure or hose malfunction. Propane Regulator ...

  • Page 110: Propane Use And Safety

    Section 7: Fuel & Propane System Propane Use and Safety Propane is a colorless and odorless gas that, in the liq- uefied state, resembles water. An odorant (usually a sulfur compound) is added as a warning agent. If you smell propane within the vehicle, quickly and carefully perform the procedure listed on the propane system la- bel.

  • Page 111: Cooking With Propane Gas

    Section 7: Fuel & Propane System If you have double cylinders on your recreation vehicle, use only one at a time. Otherwise, the propane supply will be drawn equally from both cylinders until the supply has been total- ly exhausted. Using one cylinder until it is empty, then using the second cylinder will allow you to fill the empty cylinder at your convenience without running totally out of propane.

  • Page 112: Traveling With Propane

    Section 7: Fuel & Propane System Propane consumption chart NOTE: Some states prohibit propane appliances to be operat- ed during travel, especially in underground tunnels. Make sure you know the laws for the areas where you travel. The following chart provides average propane con- sumption information.

  • Page 113: Main Supply Hose

    Section 7: Fuel & Propane System Attach the 1/4” inverted flare x 24” Type 1 pigtail hose to the regulator inlet and the right hand swivel nut to the cylinder valve. Secure the cylinder to the A-frame bracket using the bolts, nuts and washers provided. Double Cylinder Mounted On A-Frame (if so equipped) When a second cylinder is installed, a tee check valve is used to replace the 90°...
  • Page 114 Section 7: Fuel & Propane System Notes:...

  • Page 115: Section 8: Plumbing System

    Section 8: Plumbing System Plumbing System There are two different water systems in your recreation vehicle: The fresh water system consists of the fresh water holding tank, faucets and con- nections, water pump, outside shower assembly (if so equipped), water heater, tub/ shower, and water purification system (if so equipped).

  • Page 116: Fresh Water System

    Section 8: Plumbing System (lowest) to right (highest) to indicate the estimated auxiliary battery condition. The LEDs on the panel indicate the following: C = Charge at 12.7 volts G = Good at 12.1 volts F = Fair at 11.6 volts L = Low at 6.0 volts NOTE:When using shore power all 4 LEDs will light.

  • Page 117: Water Pressure Regulator (Customer Supplied)

    Section 8: Plumbing System Water Pressure Regulator (customer supplied)  A water pressure regulator is recommended to prevent damage to the plumb- ing system or components. To prevent damage when using the city water connection, a 45 lb. (315 KPa) rated water pressure regulator is recommended. Excessive pressure from the water supply source may be encountered in some parks, espe- cially in mountain regions when using the fresh water inlet or black tank flush.

  • Page 118: Fresh Water Connections

    Section 8: Plumbing System NOTE: In some models the water pump switch will be a black rocker switch located near the sink cabinet .The water pump switch should be in the OFF position when the RV is left unattended for any amount of time. If something would happen to the water system, this may help limit water damage to a smaller area.

  • Page 119: Potable Water Label

    Section 8: Plumbing System for an explanation on configuring the bypass valves. Bypass valves are normally lo- cated near the water heater. The fresh water connection should be unscrewed (i.e., the non-toxic drinking water hose dis- connected) when the recreation vehicle is left unattended for any amount of time. If some- thing would happen to the water system, this may help limit water damage to a smaller area.

  • Page 120: Sanitizing/Winterizing The Plumbing System (No Utility Center)

    Section 8: Plumbing System Open the “low point drains” by turning, then pulling the handles up. They are installed at the lowest point of the water lines. A la- bel is placed on the outside of the RV to indicate where the drains are located.

  • Page 121: How To Sanitize

    Section 8: Plumbing System NOTE:: Valve D is the suction (siphon) valve that has the clear hose attached to it for siphoning in antifreeze, sanitizer or fresh water from an external container. Valve E (if equipped) is a shutoff valve for the fresh water tank.
  • Page 122 Section 8: Plumbing System 10. Close the hot water faucets and repeat opening all cold water faucets one by one until you smell chlorine. Include outside shower faucets (if swo equipped) and toilet. 11. Turn OFF the water pump. 12. Let the solution remain in the tank & lines for at least four hours when disinfecting with 50-PPM residual chlorine.

  • Page 123: Winterizing The Plumbing System

    Section 8: Plumbing System After draining the system: Water heater power should be OFF (both switches: electric and LP gas). Water heater bypass valves should be set to BYPASS. Put the vinegar solution into the fresh water tank. Pour the vinegar solution into the gravity fill using a hose (or funnel).

  • Page 124: Water Heater Drain Plug Location

    Section 8: Plumbing System NOTE: The water heater must be drained to prevent damage from freezing. It is recommended the water heater be drained and bypassed during the winterization process particularly if introducing RV antifreeze into the plumbing system. Do not drain the water heater while it is hot or under pressure! Antifreeze should be kept out of the water heater.
  • Page 125 Section 8: Plumbing System Run the pump until it is dry (approximately 15 to 20 seconds). Operating the pump longer than that with no water can damage the pump. Open all faucets in the RV. If there is an outside shower, attach the show- er hose to the shower, and open the shower faucets.
  • Page 126 Section 8: Plumbing System Turn water heater power OFF. Turn water heater gas valve (if so equipped) OFF (out- side of the RV). Water heater bypass valves should be set to BYPASS. Refer to Water Heater Bypass Section. Water is prevented from entering the water heater. Level the RV and drain the fresh water plumbing system.

  • Page 127: Water Heater

    Section 8: Plumbing System When you are done adding RV antifreeze: Turn the water pump OFF. Turn siphon valve OFF. Remove the clear hose from the container of RV antifreeze. Leave the water tank shutoff valve (Valve E if equipped) closed to keep antifreeze out of the fresh water tank.
  • Page 128 Section 8: Plumbing System controls. Double check the bypass valves, make sure they are set properly. Always open both the hot and cold water faucets when filling the fresh water tank to allow air pockets to be forced out of the water heater. Water heater switch (if so equipped) The “propane GAS”...

  • Page 129: High Altitude Deration

    Section 8: Plumbing System Operating the water heater without the proper anode rod protection will decrease tank life and will void the tank manufacturer’s warranty on the tank. To extend the anode life, drain the water from the wa- ter heater tank whenever the RV is not being used. Avoid any extended time of non-use with water in the tank.

  • Page 130: Outside Shower (If So Equipped)

    Section 8: Plumbing System  Do not place a valve between the pressure and temperature (P&T) valve and the tank. Do not remove or plug the relief valve under any circumstances. Maintenance Do not allow the burner to burn with a yellow flame, or continue to operate the water heater with an improper burner flame.

  • Page 131: Faucets

    Section 8: Plumbing System NOTE: The shower head may be removed from the hose so that it will drain faster. If you remove the shower head, be sure to reas- semble it prior to storage. NOTE: When putting the shower assembly back into the storage compartment, make sure the hose is not pinched or the shower head is positioned in a way it can be damaged.

  • Page 132: Black/Grey Water System And Tanks

    Section 8: Plumbing System Maintenance Refer the manufacturer’s user guide or label instructions for detailed cleaning information. The tub/shower walls are made of ABS plastic material. Use a mild detergent soap and warm water to clean. Do not use gritty or abrasive particle soaps or scouring compound to clean ABS plastic.

  • Page 133: Black/Grey Water Holding Tanks

    Section 8: Plumbing System Black/Grey Water Holding Tanks Dump the gray and black water holding tanks before traveling to avoid carrying unnecessary weight. The weight of the holding tank contents is not calculated into the RV cargo carrying capacity (this extra weight would reduce your available cargo capacity). Traveling with full holding tank(s) could possibly cause you to exceed the individual tire ratings and/or the RV GAWR or RV GVWR.

  • Page 134: Black Tank Flush (If So Equipped)

    Section 8: Plumbing System Open the grey tank dump valve (depending on your model the valve will be located under the RV or on the utility center). Close the dump valve when the grey holding tank is emptied. Remove, clean and store the sewer hose. Close the sewer hose housing dust cap.

  • Page 135: Toilet

    Section 8: Plumbing System Dump the black water tank (see Gray Tank Drain and Black Tank Drain) and leave the black tank drain valve open. Connect a garden hose from the water supply source to the black tank flush. With the water source turned ON, flush the black water holding tank until the water running out of the black tank drain valve is clear (not discolored or cloudy).
  • Page 136 Section 8: Plumbing System Sewage (black) tank preparation Release one to two quarts (1 or 2 liters) of water into the toilet bowl. Follow the directions on your (approved RV) toilet chemical bottle (customer sup- plied), by placing the recommended quantity of holding tank chemical into the toilet bowl.

  • Page 137: Section 9: Heating & Cooling

    Section 9: Heating & Cooling Air Conditioner The air conditioning system is controlled by a thermostat. Cooled air enters the RV through the grill. Make sure you have sufficient power available before operating the air conditioner. Do not operate the air conditioner without the return air filter. Operating the system without the filter allows the lint and dirt that is normally stopped by the filter to accumulate on the cooling coil of the air conditioner.

  • Page 138: Furnace

    Section 9: Heating & Cooling Furnace The furnace installed in your recreation vehicle is controlled by a 12-volt DC thermostat. Depending on your model, there may be up to two thermostats enabling you to control the temperature to your comfort level. The furnace requires both 12-volt power and propane gas for full operation.

  • Page 139: Cooking Safety

    Section 10: Appliances General Cleaning Microwave and Convection Microwave IMPORTANT: Before cleaning, make sure all controls are off and the microwave oven is cool. Always follow label instructions on cleaning products. To avoid damage to the microwave oven caused by arcing due to soil buildup keep cavity, microwave inlet cover, cooking rack supports, and area where the door touches the frame clean.

  • Page 140: Cooktops: Range And Oven (If So Equipped)

    Section 10: Appliances Cooktops: Range and Oven (if so equipped) For detailed operating and safety information, refer to the manufacturer’s user guide.  During and after use, do not touch or let clothing or other flammable ma- terial come in contact with the top burners (or heating elements), burner grates or other areas near the top burners or oven until they have had sufficient time to cool.

  • Page 141: Gas Drop-In Cooktops (If So Equipped)

    Section 10: Appliances  Do not use aluminum foil on the electric range cooktop, as this material will damage the cooktop surface if it melts. Do not use aluminum foil under any circumstances on the electric range cooktop. Gas Drop-In Cooktops (if so equipped) Depending on your model, it may be equipped with either a 2 burner or 3 burner cooktop.

  • Page 142: Gas Bbq Grill (If So Equipped)

    Section 10: Appliances Gas BBQ Grill (if so equipped)  Be sure to read, understand and follow all information supplied with your recreation vehicle concerning the use of propane before operating the BBQ grill. The propane hose must be correctly connected before lighting the grill.

  • Page 143: Gas Grill And Mounting

    Section 10: Appliances Rail Mount (if so equipped) Hang the grill bracket on the aluminum mount- ing strip located on the side of the recreation vehicle. Open the (2) folding arms on the bracket mak- ing sure they lock in position. Slide the grill onto the (2) arms against the stops.

  • Page 144: Range Hood (If So Equipped)

    Section 10: Appliances Range Hood (if so equipped) If your recreational vehicle is equipped with a range hood, it will be connected to an exterior vent. The vent has an inner flap with two snaps. This flap can be snapped shut when the vehicle is in motion, or during storage to keep insects, debris, snow, rain, etc.

  • Page 145: Cleaning The Interior

    Section 10: Appliances  The ice maker (if so equipped) should be turned off and the ice tray emptied when power to your recreation vehicle has been shut off. With no power, the ice will melt and water may “pool” in the refrigerator door. When power is restored, the vibration may cause this water to run out of the door and on to the vehicle floor.

  • Page 146: Cleaning The Exterior

    Section 10: Appliances If you need to clean the condenser: Remove the base grille. Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area of the condenser. Replace the base grille when finished.

  • Page 147: Exterior Refrigerator

    Section 10: Appliances Attaching the “quick coupler” connection The “quick coupler” is directly connected to the RV propane system. The “quick-coupler” con- nection has a positive shut-off valve as required by code and standards. Quick Connect Coupler Place the “quick coupler handle in the OFF position and push back the sleeve.
  • Page 148 Section 10: Appliances  The grill requires proper ventilation. It is designed for RV outdoor use only. NEVER put lava rocks or charcoal or anything else on or under the grate. Grill is designed so it does not require those items. Serious injury or property damage can occur by placing foreign objects on the grate.

  • Page 149: Section 11: Electronics

    Section 11: Electronics HDTV Antenna/Satellite System(s) HDTV Antenna (if so equipped) Your recreation vehicle is equipped with an exterior fixed height high definition TV antenna. This antenna rotates 360° and is capable of re- ceiving any over-the-air (OTA) high definition television signals being broadcast in your receiving area.
  • Page 150 Section 11: Electronics Notes:...

  • Page 151: Section 12: Interior

    Section 12: Interior Cleaning The Interior To keep the value of your recreation vehicle, perform regular maintenance using the proper materials and procedures. Using the wrong cleaner may result in damage to the surfaces in your vehicle. Check with the manufacturer’s information for the recommended cleaning agent.

  • Page 152: Cabinetry And Tables

    Section 12: Interior Mini Blinds: A simple dry rag may do the trick. If they are especially dirty, you can use cold or warm water to clean them; never use hot water. Fill a spray bottle with water and a tiny amount of soap. Then spray a lint-free towel with the mixture and use the towel to wipe down each slat.

  • Page 153: Abs Plastics

    Section 12: Interior NOTE: Oil based soaps and cleaners are not recommended. No abrasive cleaners or alcohol cleansers should be used. If other cleaner solutions are used, we recommend trying a spot in an incon- spicuous area. ABS Plastics Dust and wipe clean with soft, damp cloth or chamois, wiping gently. Do not use gritty or abrasive particle soaps or scouring compound to clean ABS plastic.

  • Page 154: Cube Sofa

    Section 12: Interior Cube Sofa The Cube Sofa functions similar to a residential futon. The slanted back pillows offer nu- merous options as a sofa, along with the ability to extend the cushions for additional sleeping space. Booth Dinette (if so equipped) The dinette is designed to seat up to four adults.

  • Page 155: Pantry Or Hutch (If So Equipped)

    Section 12: Interior Pantry or Hutch (if so equipped) Your recreation vehicle may have a pantry or hutch that you can use for storage. Make sure all items stored in the pantry or hutch are secured to prevent shifting during travel. This cabinetry has been designed to accommodate the normal camping items which may be bulky but not necessarily heavy.

  • Page 156: Flooring

    Section 12: Interior Run cold water when pouring hot/boiling water into the sink. Solid surface sink maintenance Occasionally, clean the solid surface sink by filling one-quarter full with a 50/50 water/ bleach solution. Let soak for 15 minutes, and then wash sides and bottom of sink as solu- tion drains.

  • Page 157: Unfolding The Sofa

    Section 12: Interior  The slide out must be fully extended before putting the Murphy bed in the sleeping position. The Murphy bed must be in the stored position before the slide out can be moved to the in (travel) position. Failure to do so may result in injury or property damage This label has been installed in your recreation- al vehicle at the foot end of the Murphy bed.

  • Page 158: Storing The Murphy Bed

    Section 12: Interior  Snap hooks (if present) must be attached to the steel rings on the sofa arms before using the bed. Failure to attach these snap hooks to the steel loops on the sofa can result in serious injury or property damage. MAKE SURE THE SAFETY STRAPS AT EACH SIDE OF THE FOOTBOARD ARE ATTACHED TO THE STEEL LOOPS ON THE SOFA ARMS BEFORE PUT-...

  • Page 159: Bed Storage

    Section 12: Interior  Keep hands and fingers away from the collapsing footboard and struts when pushing the bed back in to the storage position. Secure the two “D” bolts on each side of the bed. Flip the sofa back up into the seated position: ○...

  • Page 160: Heated Bed Mats (If So Equipped)

    Section 12: Interior  Before lifting, be sure there is nothing on the bed that will restrict its movement or add extra weight. Use caution when opening or closing the bed to keep hands and fin- gers at the end ledge provided (not on the side or farther back than necessary).

  • Page 161: Bunk Beds (If So Equipped)

    Section 12: Interior Do not use pins or any heavy, sharp pointed objects on the heated bed mats. They may damage the heating elements. Be sure the heated bed mats are used on a 120 volt AC circuit. Turn off the electric current when this bedding is not in actual use. Maintenance Unplug the bed mats first.
  • Page 162 Section 12: Interior  Exercise extreme care when entering or exiting the bunk beds and using the ladder (if so equipped). Do not allow more than one person on the top bunk. Do not allow children under 6 years of age to use the upper bunk. Do not allow horseplay on or under the bed and prohibit jumping on the bed.

  • Page 163: Section 13: Exterior

    Section 13: Exterior Cleaning the Exterior To protect your recreation vehicle’s exterior finish, wash it often and thoroughly. For recreation vehicles with painted exterior graphics: If desired you may wash and wax your vehicle 60 days after purchase. The exterior paint does need time to cure before any wax is applied to the exterior surface.
  • Page 164 Section 13: Exterior Drying the recreation vehicle is just as important as washing your vehicle. Tap and well water contain many chemicals that could water stain your vehicle’s finish. We suggest using a damp natural or synthetic chamois. There are other drying products such as lint-free micro-fiber towels that work just as well.

  • Page 165: Frame

    Section 13: Exterior Polishing your recreation vehicle If painted surfaces have been severely damaged and have lost their original luster and color tone, polish the surface lightly with a fine polishing compound. Avoid limiting your polish- ing to the damaged surface only; polish a somewhat wider area, moving the polishing cloth in one direction.

  • Page 166: Exterior Roof And Sidewall Vents

    Section 13: Exterior Exterior Roof and Sidewall Vents Inspect the roof vents (including sealants) for cracks and keep them clean. Inspect the re- frigerator and holding tank vents for blockages from bird nests, spider webs, leaves, etc. All exterior access doors and vents need to be kept clean and free of obstructions (i.e., insect nests, mud daubers, etc.) while the appliances are in use.

  • Page 167: Sealants

    Section 13: Exterior  LADDER CAPACITY MAXIMUM 300 lbs (136 kg) DO NOT exceed the ladder maximum weight rating. The maximum rating includes the person’s weight PLUS weight of items carried. When climbing: • Always face the ladder. • Climb slowly with weight centered between side rails. •...

  • Page 168: Travel Trailers - Sealant Diagram

    Section 13: Exterior If you notice water inside the recreation vehicle, immediately have the dealer check for the source of the leak. Failure to correct the leak may result in serious damage to your recreation vehicle; this damage may not be warrantable. Although the following diagrams may not accurately reflect the exact model of your recre- ation vehicle, make sure you inspect all sealants as indicated in the text.

  • Page 169: Travel Checklist

    Section 14: Travel/Camping/Storage Checklists Travel Checklist Following is a preliminary list of items that need to be checked before leaving your home or campsite. This is a general list, which you may want to customize as you determine your own needs. Safety Make sure you follow all safety precautions noted in this owner’s manual and in any manufacturer’s operators manual when preparing to travel.

  • Page 170: Rv Storage

    Section 14: Travel/Camping/Storage Checklists Before leaving the campsite Check the area under the RV after overnight parking and look for water or other fluid leaks. If leaks are detected, find the cause and correct it immediately. Turn off propane tanks. Empty black and gray holding tanks, rinse as needed (if so equipped).
  • Page 171 Section 14: Travel/Camping/Storage Checklists Close the propane cylinder valve(s). We recommend using a propane cylinder cover, and to make sure the propane regulator is covered. If is equipped with a gas/electric DSI range, light a range gas burner to consume any gas remaining in the lines.
  • Page 172 Section 14: Travel/Camping/Storage Checklists Notes:...

  • Page 173: Featured Components Quick Reference Chart

    Your recreation vehicle may be equipped with some of the items listed below. This is a partial listing and it is not intended to cover all components. All information is the latest available at the time of publication. Jayco reserves the right to change any of the following information without notice.
  • Page 174 Section 15: Additional Information Thermostat Coleman Mach www.airxcel.com/coleman-mach Toilet Thetford Corp. www.thetford.com See manufacturers’ user guide Winegard Company www.winegard.com TV Antenna King Jack www.kingconnect.com Water Heater, Tank DSI Atwood Greenbrier www.atwoodmobile.com Girard Systems www.greenrvproducts.com Water Heater, Tankless Truma AquaGo www.truma.com Shurflo East www.shurflo.com Water Pump, 12V...

  • Page 175: Vehicle Maintenance Record

    Section 15: Additional Information Vehicle Maintenance Record Make: Model: Model Year: Vehicle Serial#: Service Performed Mileage Work Performed Notes Date...

  • Page 176: Ownership Notification

    Section 15: Additional Information Jayco Ownership Notification Fax Form To: (800) 825-7876 ATTENTION! Federal record keeping laws require that we maintain a file of owners of our product. Your cooperation in filling out this from will be appreciated. □ □...
  • Page 177 Section 15: Additional Information Notes:...

Table of Contents