Table of Contents
Advertisement
Available languages
Available languages
en
ENGLISH
Loss of cutting performance
Saw blade blunt (possibly tempering marks on
blade body):
• Replace saw blade (see chapter 10.
Maintenance).
Chip ejection blocked
No dust collector connected or suction capacity
insufficient:
• Connect extraction system or increase suction
capacity (air speed 20 m/sec at chip ejection
tube).
13. Accessories
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Saw blade Power Cut
Order no.: 6.28025
- For rough and medium-fine cuts with rapid
movement and limited power requirements
- Good cutting results for longitudinal cuts in solid
wood
Saw blade Precision Cut
Order no.: 6.28059
- Very wide range of applications in wood
processing
- For very good, clean cutting results for straight
and cross cuts in soft and hard wood
- Well suited for hard wood and plywood, untreated
chipboards, coated or veneered, MDF, composite
materials
Circular saw blade Multi Cut
Order no.: 6.28093
- Universal use for demanding materials
- When high cutting quality is required, e.g.
laminate, plastic, thin-walled aluminium, copper,
and brass profiles
- Ideally suited for many applications in interior
construction
- Perfect cutting results also for cross cuts in solid
wood, uncoated, coated or veneered chip board,
MDF
Push stick (as replacement)
Order no.: 343433180
For a complete range of accessories, see
www.metabo.com or the catalogue.
14. Repairs
Danger!
For safety reasons, repairs to power tools
must be carried out by qualified electricians
only using original spare parts!
A defective mains cable must be replaced only
with a special, original mains cable from Metabo
available from the Metabo service.
Please contact your Metabo service centre if you
have Metabo devices that require repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
15. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of
disused machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/
EU on Waste from Electric and Electronic
Equipment and implementation in national law,
used power tools must be collected separately
and recycled in an environmentally-friendly
manner.
16. Technical Specifications
Explanatory notes on the specifications on page 3.
20
Subject to change in accordance with technical
progress.
U
= mains voltage (~ alternating current)
P
= Rated input power
1
I
= Rated current
F
= Min. fuse protection
IP
= protection class
n
= No-load speed
0
v
= Max. cutting speed
0
W
= thickness of splitting wedge
D
= saw blade diameter (outer)
d
= saw blade hole (inside)
b
= cutting width
a
= max. base body thickness of the saw
blade
T
= cutting height with vertical saw blade
90°
T
= cutting height with saw blade inclination
45°
of 45°
S
= saw blade swivel range
x°
L
= max. cutting width with ripping fence
p
L
= max. cross-section with angle guide
W
A
= dimensions without machine stand
1
(lxwxh)
S
= length of saw table
L
S
= width of saw table
B
m
= machine weight
Measured values determined in conformity with
EN 62841.
~
AC power
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be
higher or lower depending on the operating
conditions, the condition of the power tool or the
accessories. Please allow for breaks and periods
when the load is lower for assessment purposes.
Arrange protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Typical A-effective perceived sound levels:
L
= Sound-pressure level
pa
L
= Acoustic power level
WA
K
, K
=Uncertainty
pA
WA
Wear ear protectors!
Advertisement
Chapters
Table of Contents
