Table of Contents
Advertisement
GENERAL USE:
Water quality (standard):
– The recommended water quality must comply with the following standards.
– Chlorine concentration less than 2.5 ppm
– pH between 6.9 and 8
– In case of sudden chlorination, isolate the heat pump by shutting the inlet and outlet valves of the device, and reset them to their initial
positions after treatment.
USE
– Cover the pool with a cover (bubble cover, shutter...) to reduce heat losses.
Maintaining the temperature:
– Once the desired temperature has been reached, you can set the daily filtration time according to your habits (8 to 10 hours per day minimum
during the season). The heat pump will start automatically whenever necessary. The minimum operating time varies based on the time of use,
please contact your distributor for further information.
If you notice the water temperature of the pool is falling, despite the device operating continuously, increase the daily filtration time.
Do not forget to cover the pool with an insulated cover when you are not using it, to limit heat losses.
IMPORTANT: a swimming pool without a cover will lose 4 times more energy than the same pool with a cover.
The choice of the heat pump should always take into account the presence of a tarpaulin, a rolling shutter, or any other type of protection of the
pool when it is not being used.
REVERSIBLE DISPLAY LOCATION:
This HP is designed to make it possible to choose the side on which the screen will be positioned.
1: Open the access hatch
2: From the inside, unplug the display connector from the white cable
3: From the outside, unscrew the lateral steel panel with the opening for the display (7 screws)
4: From the outside, unscrew the oposite steel panel as well
5: Unclip the display from his position and clip it on the oposite niche.
6: From the inside, move the connector + white cable to the opposite side
7: Reconnect the display and check if the display is correctly running
8: Put the steel panel with an opening on the display side.
9: Replace the screws back and tight.
10: Apply the same process to the complete steel panel
11: Close the access hatch
PENTAIR TEMP App
Make sure the heat pump can receive a WiFi signal. Take a recent smartphone, activate Bluetooth.
- On Apple and Android store, download the Pentair Temp App then create your account by following the steps.
- Scan the QR code located behind the access hatch to connect your IntelliTemp. You can now control your heat pump
remotely. Activate the Bluetooth connection of your HP by pressing the pairing button on the WiFi module installed
on top of the electrical box for 10 seconds.
- You can now control your heat pump remotely. Once the heat pump is connected, our technicians can intervene
remotely if necessary.
INSTALLATIONS
INTELLITEMP
INSTALLATIONS
18°C
INTELLITEMP
26°C
28°C
12
INTELLITEMP
18°C
INTELLITEMP
INTELLITEMP
18°C
26°C
28°C
OFF
28°C
OFF
28°C
28°C
MODES
RÉGULATION
RUNNING
MODES
SMART
MODES
RÉGULATION
RUNNING
RÉGULATION
SMART
AUTO
SMART
INTELLITEMP
18°C
18°C
INTELLITEMP
18°C
28°C
22°C
28°C
22°C
13°C
MODES
2022 10 18
LOW FLOW
RÉGULATION
RUNNING
2022 10 15
LOW FLOW
AUTO
SMART
AUTO
2022 10 18
MODES
LOW FLOW
RUNNING
2022 10 15
RÉGULATION
LOW FLOW
AUTO
MODES
RÉGULATION
RUNNING
INTELLITEMP
INTELLITEMP
18°C
INTELLITEMP
18°C
28°C
REGULATION
13°C
ECO
SMART
BOOST
RUNNING
INTELLITEMP
INTELLITEMP
POMPE À CHALEUR
18°C
18°C
POMPE À CHALEUR
18°C
18°C
REGULATION
RUNNING MODE
ECO
HEATING
RUNNING MODE
HEATING
SMART
AUTO
AUTO
BOOST
COOLING
COOLING
Advertisement
Table of Contents
