1. Manuals
  2. Brands
  3. Baroness Manuals
  4. Lawn Mower
  5. LM3210A
  6. Owner's operating manual

Baroness LM3210A Owner's Operating Manual

5-unit reel mower
Hide thumbs Also See for LM3210A:
Table of Contents

Advertisement

Quick Links

Download this manual
5-Unit Reel Mower
Owner's Operating Manual
Serial No.
LM3210A：11045-
"Required reading"
Read this manual before using the machine.
Original Instructions Ver.1.4

Advertisement

Table of Contents
loading

Related Manuals for Baroness LM3210A

Summary of Contents for Baroness LM3210A

  • Page 1 5-Unit Reel Mower Owner's Operating Manual Serial No. LM3210A：11045- "Required reading" Read this manual before using the machine. Original Instructions Ver.1.4...
  • Page 2 LM3210A Regulations California Proposition 65 EU Emission Control (StageⅤ) (For California, USA) (For Europe) Important WARNING: No deliberate tampering with or misuse of the Operating, servicing and maintaining engine emissions control system should take a passenger vehicle or off-road place.
  • Page 3 LM3210A Greeting Thank you for purchasing the Baroness product. QR Code This manual describes the proper handling, adjustment, and inspection of your product. A QR code label is affixed on the machine. We hope you will use the product safely, and take advantage of its best performance.
  • Page 4 The operator is responsible for operating the product properly and safely. Maintenance service for this machine should be performed by a mechanic with expertise. If you have any questions concerning maintenance or genuine parts, please contact a Baroness dealer or Kyoeisha.
  • Page 5 When replacing parts, be sure to use genuine Baroness parts or parts designated by Kyoeisha. Note that the Baroness product warranty may not apply to defects caused by the use of parts from other companies. Prior to use, carefully read the following manuals to thoroughly understand the contents for safe and correct operation.
  • Page 6 LM3210A Introduction...

  • Page 7: Table Of Contents

    LM3210A Contents Safety .............. Page 1-1 Transporting ..........Page 5-20 Maintenance ........... Page 6-1 Safe Operating Practices .......Page 1-2 Disposal ............Page 2-1 Precautions for Maintenance ......Page 6-2 Jacking Up The Machine ....... Page 6-2 Recycle and Waste Disposal ......Page 2-2 Greasing ............
  • Page 8 LM3210A Contents...

  • Page 9: Safety

    LM3210A Safety Safe Operating Practices ...... Page 1-2 Training ..........Page 1-2 Preparation ..........Page 1-2 Operation ..........Page 1-3 Maintenance .......... Page 1-4 Storage ..........Page 1-5 Page 1-1...

  • Page 10: Safe Operating Practices

    LM3210A Safety Failure to adequately follow these safety Never allow children or people unfamiliar precautions may cause an accident resulting in with these instructions to use or service the injury or death. machine. Local regulations may restrict the age of the...

  • Page 11: Operation

    LM3210A Safety Add fuel before starting the engine. Never operate while people, especially Never remove the cap of the fuel tank or children, or pets are nearby. add fuel while the engine is running or Only operate in good light, keeping away when the engine is hot.

  • Page 12: Maintenance

    LM3210A Safety Before making height or depth adjustment Allow the engine/muffler to cool before unless adjustment can be made from the checking/maintenance. operator's position. To reduce the fire hazard, keep hot parts Before clearing blockages. such as the engine and silencer/muffler,...

  • Page 13: Storage

    LM3210A Safety Be extremely careful with high-pressure oil as it may pierce your skin, resulting in an injury. If fluid is injected into the skin it must be surgically removed within a few hours by a doctor familiar with this form of injury or gangrene may result.
  • Page 14 LM3210A Safety Page 1-6 Safe Operating Practices...

  • Page 15: Disposal

    LM3210A Disposal Recycle and Waste Disposal ....Page 2-2 About Recycle ........Page 2-2 About Waste Disposal ......Page 2-2 Page 2-1...

  • Page 16: Recycle And Waste Disposal

    LM3210A Disposal Recycle and Waste Disposal About Recycle Recycling battery etc. is recommended for environmental conservation and economical use of resources. It may be required by local laws. About Waste Disposal Make sure that waste generated when servicing or repairing the machine is disposed of in accordance with local regulations.

  • Page 17: Product Overview

    LM3210A Product Overview Specifications ........Page 3-2 Specifications .........Page 3-2 Sound Pressure Level ......Page 3-3 Sound Power Level ....... Page 3-3 Vibration Level ........Page 3-3 Carbon Dioxide (CO2) Emissions ..Page 3-3 Names of Each Section ......Page 3-4 Regulation Decals ........Page 3-5...

  • Page 18: Specifications

    LM3210A Product Overview Specifications Specifications Model LM3210A Name 5-Unit Reel Mower Mower unit type Type_F Type_R Total length 315 cm 124.06 in 330 cm 129.92 in During 367 cm 144.49 in 368 cm 144.88 in operation Total width During Dimensions 235 cm 92.52 in...

  • Page 19: Sound Pressure Level

    LM3210A Product Overview x Mowing width x Mowing width x Efficiency ← ← 0.8) 0.8) Maximum inclination for operation 15 degrees ← Front wheel 31 x 13.50 - 15 31 x 15.50 - 15 Tire size Rear wheel 20 x 12.00 - 10 ←...

  • Page 20: Names Of Each Section

    LM3210A Product Overview Names of Each Section Seat Steering handle Tilt lever Diff-lock switch Parking brake lever Brake pedal Forward pedal Reverse pedal Mower unit up/down lever Throttle knob Reel rotation switch 2WD/4WD selector switch Reel rotation/stop switching lever Fuel tank...

  • Page 21: Regulation Decals

    LM3210A Product Overview Regulation Decals Specification Decal (For Europe) Positions of Regulation Decals CE mark indicates that the machine sold in the EU nations complies with the EU requirements. The Specification decal indicates the CE marking, model , and weight, etc.
  • Page 22 LM3210A Product Overview Noise Emission Decal ROPS Caution Decal (For Europe) ROPS caution decal describes the following The noise emission decal indicates the sound caution messages. power level determined by measuring Replace damaged ROPS. ･ identical machines in accordance with the Do not repair or revise.
  • Page 23 LM3210A Product Overview Recycle Decal California Proposition 65 Decal (Riding Type) Recycle Decal illustrates Recycle Mark in (For the State of California, USA) accordance with local regulation. California Proposition 65 decal describes the (For Europe) warning messages as required by California Proposition 65.

  • Page 24: Safety Signs And Instruction Signs

    49003365 Positions of Safety Signs and Instruction Signs_002 Part numbers for decals that need to be replaced are listed in the parts catalog. Order them from a Baroness dealer or Kyoeisha. Positions of Safety Signs and Instruction Signs 6iul4h-040...
  • Page 25 LM3210A Product Overview Operation decal Start/stop decal (reel) Caution to mutilation decal Caution for high temperatures decal Caution to injury decal Caution to rotating object decal Hydraulic oil icon Diesel fuel icon Fire prohibited decal 6iul4h-056 Caution for mower lock decal...

  • Page 26: Description Of Safety Decals And Instruction Decals

    Turn the key to the "ON (GLOW)" Warning position, and then wait for the "BARONESS" logo to turn off. Apply the parking brake, stop the engine, Turn the key to the "START" position. remove the ignition key, and then leave the machine.
  • Page 27 LM3210A Product Overview Caution to Mutilation Decal Caution to Injury Decal K4205001600 K4205001580 DECAL, CAUTION TO MUTILATION Decal, caution to injure Warning Caution May cut your hand or leg - Stop the cutter May pinch - There is a risk of being pinched.
  • Page 28 LM3210A Product Overview Hydraulic Oil Icon Fire Prohibited Decal K4209000980 K4205001940 Hydraulic oil icon Decal, fire prohibited Read the Owner's Operating Manual. Warning Keep away from fire. i77xz6-001 Hydraulic Oil Icon_001 Diesel Fuel Icon r653fo-001 K4209001000 Fire Prohibited Decal_001 Diesel fuel icon Caution for Mower Lock Decal Use diesel fuel.
  • Page 29 LM3210A Product Overview Caution for Spouting Coolant Decal Caution Exhaust Gas Decal K4205001970 K4205001950 Decal, caution for spouting coolant Decal, caution exhaust gas Caution Warning Caution for spouting coolant - Do not open Caution for exhaust gas while hot. High temperature - Do not touch. Otherwise, you will get burned.
  • Page 30 LM3210A Product Overview Maintenance Decal 2WD/4WD Selector Important Decal K4209001950 K4205002330 Label, maintenance DECAL, IMPORTANT 2WD/4WD SELECTOR The maintenance decal indicates the Important necessary inspection and maintenance items for this machine. Be sure to operate the 2WD/4WD selector switch when the machine stops.

  • Page 31: Operation Decals

    LM3210A Product Overview Operation Decals Positions of Operation Decals STOP 6n6oux-187 Positions of Operation Decals_005 Key switch decal Reel rotation mark 6n6oux-184 2WD/4WD selector mark Positions of Operation Decals_001 DPF regeneration mark (EN) Mower unit up/down decal Light switch mark...

  • Page 32: Description Of Operation Decals

    LM3210A Product Overview Description of Operation Decals 2WD/4WD Selector Mark Key Switch Decal 2WD/4WD selector mark This indicates the 2WD/4WD positions. Decal, key switch This indicates the key switch positions. sdts98-002 2WD/4WD Selector Mark_001 v2e27i-071 Key Switch Decal_001 DPF Regeneration Mark (EN)
  • Page 33 LM3210A Product Overview Mower Unit Up/Down Decal Engine Rotation Mark Decal, mower unit up/down Engine rotation mark This indicates the Up/Down positions of the This indicates low/high speed of engine mower unit. rotation. 8kzlbt-001 kp2t9l-001 Mower Unit Up/Down Decal_001 Engine Rotation Mark_001...
  • Page 34 LM3210A Product Overview Tilt Steering Decal FORWARD Decal K4203001350 K4203001430 Decal, tilt steering Decal, FORWARD This illustrates the tilt directions of the This indicates forward travel. steering wheel and the locked/free positions. FORWARD FREE LOCK kqca3e-001 hj3943-003 FORWARD Decal_001 Tilt Steering Decal_001...
  • Page 35 LM3210A Product Overview Lapping Decal Reel Stop Decal K4203001590 K4203001310 Decal, lapping Decal, reel stop This indicates rotational direction of the reel This indicates stop of the reel cutter (cutting cutter (cutting cylinder). cylinder). v57o51-001 if834g-002 Lapping Decal_001 Reel Stop Decal_001...
  • Page 36 LM3210A Product Overview Page 3-20 Operation Decals...

  • Page 37: Description Of Functions

    LM3210A Description of Functions Proximity Sensors ......... Page 4-2 Relays ............. Page 4-2 Reel Rotation Switch ......Page 4-3 2WD/4WD Selector Switch ....Page 4-3 DPF Auto Regeneration Inhibit Switch ............. Page 4-4 DPF Parked Regeneration Switch ..Page 4-5 Light Switch ...........

  • Page 38: Proximity Sensors

    LM3210A Description of Functions Proximity Sensors There are three proximity sensors on mower arm fulcrums #3, #4 and #5. These sensors detect the raised or lowered positions of mower units #3, #4 and #5. The information is related to controlling rotation and stop of the reel cutters (cutting cylinders).

  • Page 39: Reel Rotation Switch

    LM3210A Description of Functions Reel Rotation Switch Caution When traveling, be sure to stop the rotation of Caution the reel cutters (cutting cylinders) and raise the mower units. Set the reel rotation switch to the "Rotation" position immediately before starting cutting work.

  • Page 40: Dpf Auto Regeneration Inhibit Switch

    LM3210A Description of Functions DPF Auto Regeneration Inhibit Switch Caution Normally, set the DPF auto regeneration inhibit switch to "Auto regeneration mode". However, when operating in a location where fires may occur, set the DPF auto regeneration inhibit switch to "Auto regeneration inhibit mode".

  • Page 41: Dpf Parked Regeneration Switch

    LM3210A Description of Functions DPF Parked Regeneration Switch Light Switch Note: Danger Danger Depending on the specifications, this function may not be available. Do not perform DPF regeneration in a location where fires may occur since it will become Caution extremely hot around the exhaust outlet during DPF regeneration.

  • Page 42: Reel Reverse Switch

    LM3210A Description of Functions The reel rotation/stop switching lever is located Reel Reverse Switch on the reel motor attached to each mower unit. It is used during cutting and back lapping. Important You must shift only the lever(s) for the mower unit(s) that you plan to use for cutting or back Do not switch the rotation directions, "Normal...

  • Page 43: Mower Lock Lever (Latch)

    LM3210A Description of Functions For mower units #2 and #3 xqolpb-001 bczghz-006 Mower Lock Lever (Latch)_001 Reel Rotation Adjustment Valve_002 Mower lock lever (latch) Valve for mower units #2 and #3 Mower Unit Up/Down Lever Reduce the rotation speed by loosening the lock nut, then tightening the knob.

  • Page 44: Throttle Knob

    LM3210A Description of Functions Mower unit up/down lever Neutral DOWN Note: When the mower units are raised, the reels stop rotating, even if the reel rotation switch is set to the "Rotation" position. Throttle Knob k3y8px-002 Diff-Lock Switch_001 The throttle knob is located to the right of the...

  • Page 45: Brake Pedal

    LM3210A Description of Functions Brake Pedal Brake pedals Parking brake lever The brake pedal is located in the left foot area. Safety Mechanisms To stop the machine, depress the brake pedal when needed. This machine features a safety device for starting/stopping the engine.

  • Page 46: Warning Mechanisms

    LM3210A Description of Functions Engine Warning Lamp Warning Mechanisms Warning Buzzer Important Make repairs immediately if the fault codes of Important PCD (Particulate Control Diagnostic) and When the buzzer (intermittent tone) sounds, NCD (NOx Control Diagnostic) appear. be sure to stop operation since the engine is overheated.

  • Page 47: Monitor Led

    LM3210A Description of Functions Engine warning lamp blinks when only DTC Monitor LED relevant to PCD/NCD come up. Monitor (LED) turns on when a failure occurs on the function of engine. Check the fault code (DTC) in the monitor display when Monitor (LED) turns on.

  • Page 48: Monitor

    LM3210A Description of Functions Displayed Icon Monitor The icon appears at the top of the monitor The monitor displays various information about display. the machine, such as the operating status and fault conditions. The information of desired items can be confirmed according to operating the keys.

  • Page 49: Main Menu Items

    LM3210A Description of Functions Main Menu Items 1-Up Display / 4-Up Display While any parameter is displayed, press the "GO TO 1-UP DISPLAY" / "GO TO 4-UP menu key to display the main menu with the DISPLAY" are used to set whether to display following 11 items.
  • Page 50 LM3210A Description of Functions Parameter Items ￭ The parameters and corresponding information that appear in the monitor display are listed below. Monitor display L Monitor display S Description ENGINE SPEED ENG RPM Displays the engine rpm. DRIVERS DEMAND DEMAND TQ Displays the torque required by the ECU.
  • Page 51 LM3210A Description of Functions Monitor display L Monitor display S Description EXHAUST FILTER Displays the DPF outlet gas temperature measured by the EF OUT T OUTLET TEMP exhaust temperature sensor. Shows the status of the regeneration icon. PARTICUATE TRAP PT LAMP Icon not displayed="OFF", Icon blinking="ON BLINK", Icon...
  • Page 52 LM3210A Description of Functions Text 2 ･ Language With "LANGUAGES", the language used in the monitor display can be set to either of the following two. 1 of 4 C : 3 SPN 172 FMI 3 ･ ENGLISH CORRECTIVE ACTION:...
  • Page 53 LM3210A Description of Functions Custom Setup Menu key ￭ Arrow keys With "CUSTOM SETUP", the type and Enter key number of parameters as well as their display order can be specified. Highlight "USE DEFAULTS", and then Press the menu key. After the main menu press the Enter key.
  • Page 54 LM3210A Description of Functions Change the parameters. Check that the number at the right of the parameter disappeared. To add a parameter Use the arrow keys to highlight the parameter to be added, and then press the Enter key. ENGINE SPEED...
  • Page 55 LM3210A Description of Functions When "AUTOMATIC SCAN ON" appears, Use Defaults ￭ the parameters are scrolled automatically. For manual scrolling, highlight With "USE DEFAULTS", the 4-up display "AUTOMATIC SCAN ON", and then press parameters return to the factory defaults. the Enter key.
  • Page 56 LM3210A Description of Functions "RESTORED TO DEFAULTS" appears in Highlight "CUSTOM SETUP", and then the monitor display, and the parameters press the Enter key. are reset to the factory defaults of the following 8 items. First page ･ ENGINE SPEED...
  • Page 57 LM3210A Description of Functions The parameters appear. Check that a number appeared to the The number at the right of the right of the selected parameter. parameter indicates the location in the 4-up display. 1=Upper left 2=Lower left ENGINE SPEED...
  • Page 58 LM3210A Description of Functions Check that the number at the right of Reset Reminders ￭ the parameter disappeared. With "RESET REMINDER", displayed remaining time can be reset to the time specified with "MODIFY REMINDERS". Press the menu key. ENGINE SPEED...
  • Page 59 LM3210A Description of Functions Use the arrow keys to highlight the item to Modify Reminders ￭ be changed, and then press the Enter key. A plus appears at the right of the currently With "MODIFY REMINDERS", the selected items. replacement time period for consumables can be specified.
  • Page 60 LM3210A Description of Functions Use the arrow keys to highlight the item to "MODIFY SERVICE REMINDER?" be changed, and then press the Enter key. appears. To save the changes, press the Enter key. To cancel the changes, press the menu key.
  • Page 61 LM3210A Description of Functions Reminder Display Select Units ￭ With "SELECT UNITS", the units of parameter Important values can be set to any of the following three formats. If a warning message appears, immediately stop operation, and then perform the ENGLISH ･...
  • Page 62 LM3210A Description of Functions Units Adjust Backlight Monitor display S ENGLIS METRI METRI With "ADJUST BACKLIGHT", the brightness C KPA C BAR of the monitor display can be adjusted. ENG RPM Press the right arrow key to make the display DEMAND TQ ％...
  • Page 63 LM3210A Description of Functions Utilities With "UTILITIES", the remaining fuel volume can be specified and the monitor configuration can be displayed. 0 RPM 83 % ENG RPM % SOOT The following 6 items appear when 19 C NO DATA "UTILITIES" is selected.
  • Page 64 LM3210A Description of Functions Highlight "FUEL LEVEL", and then press Low Fuel Level Display the Enter key. Important If a warning message appears, immediately stop operation, and then supply fuel. BACKLIGHT DIMMER FUEL LEVEL When the fuel level falls below the...
  • Page 65 LM3210A Description of Functions A warning mark appears in the upper- Fault Code Displays right corner of the monitor display. Important When the fault code (DTC) appears in the monitor display, contact your dealer. 0 RPM 83 % A fault code (DTC) appears in the monitor...
  • Page 66 LM3210A Description of Functions Pressing the Enter key changes the screen Text 2 ･ from the fault code to the parameter display. The corrective action appears. Important If the service reminders are configured, the notices of the replacement time period for...

  • Page 67: Engine

    LM3210A Description of Functions Text 2 ･ Engine The corrective action appears. Handling Tier 4 Emission Control Compliant Engine The engine installed in this vehicle meets Tier 1 of 1 WARNING 4 emission control for "non-road emission SPN 110 FMI 3 CORRECTIVE ACTION: regulation."...
  • Page 68 LM3210A Description of Functions DPF Regeneration Caution Normally, set the DPF auto regeneration Danger Danger inhibit switch to the "Auto regeneration mode". However, when operating in a location where Since it will become extremely hot around the fires may occur, set the DPF auto exhaust outlet during DPF regeneration, do regeneration inhibit switch to the "Auto...
  • Page 69 LM3210A Description of Functions When the regeneration completed, the Important regeneration icon disappears. When the system enters the level where DPF regeneration is required, perform the regeneration immediately. Interrupting the regeneration or ignoring the warning and continuing traveling or cutting...
  • Page 70 LM3210A Description of Functions Stop traveling and cutting work. Important Park this machine in a safe location. If the regeneration remains uncompleted in Apply the parking brake. automatic regeneration, parked regeneration Set the throttle opening to 0% (idling). is required with the blinking regeneration icon.
  • Page 71 LM3210A Description of Functions Important When the system enters the level where DPF regeneration is required, perform the 1 of 2 C : 1 regeneration immediately. SPN 3701 FMI 15 E x c e s s i v e P M 3...
  • Page 72 LM3210A Description of Functions ■In PM accumulation "Level 4": Contact your dealer for manual regeneration. Important Replacement of DPF If ignoring the manual regeneration requirement and continuing traveling or cutting When PM accumulates excessively in the work in PM accumulation "Level 4", PM DPF or ash accumulates, replace the DPF accumulation level enters "Level 5".
  • Page 73 LM3210A Description of Functions Stop traveling and cutting work. Conditions for DPF Regeneration Park this machine in a safe location. Apply the parking brake. Danger Danger Stop the engine. Since it will become extremely hot around the Contact your dealer for DPF replacement.
  • Page 74 LM3210A Description of Functions <Automatic regeneration> PM Accumulation Level ■When the DPF auto regeneration inhibit switch set to the "Auto regeneration mode": Level 0 ￭ When the conditions for automatic DPF regeneration is not necessary. regeneration are met, the automatic...
  • Page 75 LM3210A Description of Functions <Parked regeneration> Press the DPF parked regeneration switch. These are the conditions for activating ･ Parked regeneration starts and the parked regeneration. regeneration icon changes from blinking to The parking brake is applied. lighting. The traveling pedal is in neutral.
  • Page 76 LM3210A Description of Functions <Automatic regeneration> <Parked regeneration> ■When the DPF auto regeneration inhibit These are the conditions for activating ･ switch set to the "Auto regeneration mode": parked regeneration. When the conditions for automatic The parking brake is applied.
  • Page 77 LM3210A Description of Functions Press the DPF parked regeneration These are the statuses in PM switch. accumulation "Level 3". Parked regeneration starts and the regeneration icon changes from blinking to lighting. When the regeneration completed, the 1 of 2 C : 1 regeneration icon disappears.
  • Page 78 LM3210A Description of Functions When the regeneration completed, the These are the statuses in PM regeneration icon disappears. accumulation "Level 4". Level 4 ￭ Danger Danger Since it will become extremely hot around the 1 of 2 C : 1...
  • Page 79 LM3210A Description of Functions Level 5 ￭ When PM accumulates excessively in the DPF or ash accumulates, replace the DPF since the regeneration in that case is prohibited. You can not continue to use this machine ･ for traveling and cutting work.
  • Page 80 LM3210A Description of Functions Page 4-44 Engine...

  • Page 81: Handling Instructions

    LM3210A Handling Instructions Operations Before Service ....Page 5-2 Procedure to Stop Engine ....Page 5-19 Parking and Stopping ......Page 5-19 Opening and Closing of Hood ....Page 5-2 Opening and Closing of Underseat Leaving the machine ......Page 5-19 Cover ............. Page 5-2 Move ............Page 5-19...

  • Page 82: Operations Before Service

    LM3210A Handling Instructions Hook the hood stay on the receiver on the Operations Before Service back side of the hood. Make sure that the hood is fixed, and then Opening and Closing of Hood release your hands. Caution Do not open the hood in strong winds.

  • Page 83: Inspection And Cleaning

    LM3210A Handling Instructions Cover Lever Seat Inspection of Covers Pull up Tilt forward Warning Tilt the seat forward to open the cover. If you have removed the covers during To close the cover, slowly lower the seat. inspection, be sure to securely install them in Inspection and Cleaning their original positions.

  • Page 84: Cr Brush

    LM3210A Handling Instructions CR brush Cleaning of Radiator Cover Inspection of CR Brush Important Note: An unclean radiator cover may cause Depending on the specifications, this function overheating or damage to the engine. may not be available. It may also cause malfunction of the hydraulic Bearing wear due to frequent use or bearing system.

  • Page 85: Coolant

    LM3210A Handling Instructions Coolant Cleaning of Radiator Inspection of Coolant Important An unclean radiator may cause overheating or Caution damage to the engine. Do not touch the radiator or coolant during It may also cause malfunction of the hydraulic engine operation or immediately after the system.

  • Page 86: Oil Cooler

    LM3210A Handling Instructions Coolant Supply Reserve tank If no coolant is in the reserve tank, follow Caution the steps below to fill the tank with clean water. Do not touch the radiator or coolant during engine operation or right after the engine has Open the radiator cap, and then supply been turned off.

  • Page 87: Hydraulic Oil

    LM3210A Handling Instructions Make sure that the oil level is at the middle Cleaning of Oil Cooler of the oil gauge. Important An unclean oil cooler may cause malfunction of the hydraulic system. Important Do not use solid objects, such as a spatula or screwdriver, or high-pressure water to clean the radiator or oil cooler.

  • Page 88: Hydraulic Hoses

    LM3210A Handling Instructions If the oil level is low, remove the left tank Check the hydraulic hoses and pipes, and cover, and then open the tank cap and make any necessary repairs before operating supply oil. the machine. Make sure that there is no wear, deterioration or damage in the hydraulic hoses and pipes.
  • Page 89 LM3210A Handling Instructions Press the reset button for the vacuum Cleaning of Air Cleaner Element indicator. A contaminated air cleaner element may cause malfunction of the engine. To maximize the life of the engine, clean the air cleaner properly. Important The inner element cannot be cleaned.

  • Page 90: Battery

    LM3210A Handling Instructions Inspecting the cable terminals Battery If the connection between the battery terminals and vehicle's cable terminals are Inspection of Battery loose, tighten the nuts until the cable terminals are secured firmly. Danger Danger Insufficiently tightened terminals may result...

  • Page 91: Electrical Wiring

    LM3210A Handling Instructions Tighten the vent plug securely. UPPER LEVEL line LOWER LEVEL line Supply of Battery Fluid U P P E R L E V E L L O W E R L E V E L Danger Danger Be careful not to let your skin, eyes or clothes, etc., come into contact with the battery fluid or...

  • Page 92: Brake

    LM3210A Handling Instructions Type_R Wire Tire size Pneumatic pressure 　 Inspection of Wire Front 31 x 13.50 - 140 kPa (1.4 20 psi wheel kgf/cm Inspect wires. If necessary, adjust or replace wires. 140 kPa (1.4 Rear 20 x 12.00 -...

  • Page 93: Engine Oil

    LM3210A Handling Instructions Engine Oil Supply of Engine Oil Inspection of Engine Oil Important Do not supply too much engine oil. Otherwise, Important the engine may be damaged. Securely tighten the oil level gauge and oil filler cap. Important Stop the engine, wait for 10 to 20 minutes Do not mix different types of engine oil.

  • Page 94: Fuel

    LM3210A Handling Instructions Note: Fuel The factory default low fuel level is 10%.The level can be changed optionally. Inspection of Fuel Quantity With the machine on a level surface, observe the fuel level in the monitor to check the fuel level.

  • Page 95: Water Separator

    LM3210A Handling Instructions Loosen the water drain plug and air- Water Separator bleeding bolt to drain the water into the container. Inspection of Water Separator Important If water contaminates the fuel, the supply pump and injector will seize due to heat.

  • Page 96: Fuel Filter

    LM3210A Handling Instructions Remove and clean the cup, element and Locate the leakage and identify the type of float. liquid. Replace the element with a new one Bolts and Nuts when replacement needed. Inspection of Bolts and Nuts Important Be sure to retighten the bolts and nuts, because they may be loosened at the earlier stage of the use.

  • Page 97: Adjustment Before Work

    LM3210A Handling Instructions Mower Unit Cleaning of Mower Unit Important While cleaning, do not allow water on the sealed parts of the reel shaft. (Avoid high- pressure water cleaning.) Otherwise, it may cause damage to the machine. 75uxaw-010 Adjustment of Steering Wheel Position_001 Be sure to clean the mower unit after use.

  • Page 98: Start/Stop Of Engine

    7 seconds after the key switch is turned to the "OFF" position. Make sure that the glow plug is generating heat, the "BARONESS" logo or "Warming up" message appears in the monitor display, Important and the yellow and red LEDs are lit.

  • Page 99: Parking And Stopping

    Install the rubber cap to the key switch. Hook the mower lock levers (latches) for the After the "BARONESS" logo and the yellow mower units #4 and #5. and red LEDs go off and the parameters (items and values such as the rotation Step off the machine to leave.

  • Page 100: Cutting Work

    LM3210A Handling Instructions Cutting Work Transporting Cutting Work Transporting Procedure When loading the machine into a trailer or a Caution truck to transport it, drive the machine forward. When unloading, drive the machine in reverse. Be sure to operate at an appropriate speed for If the roof is installed on the machine, remove the mowing site.

  • Page 101: Maintenance

    LM3210A Maintenance Precautions for Maintenance ....Page 6-2 Long-Term Storage ......Page 6-33 Jacking Up The Machine .......Page 6-2 About Jacking Up The Machine .....Page 6-2 Jack-Up Points ........Page 6-2 Greasing ..........Page 6-3 About Greasing ........Page 6-3 Greasing Points ........Page 6-4 Lubrication ...........

  • Page 102: Precautions For Maintenance

    First, learn well the operations you plan to perform. Important Use tools appropriate for each operation. Important Use Baroness genuine parts for replacement and accessories. Our product warranty may be void if you use non-genuine parts for replacement or accessories.

  • Page 103: Greasing

    LM3210A Maintenance Front right frame Below rear wheel motors There is one jack-up point below each rear wheel motor (left and right). rwyt62-076 Jack-Up Points_002 Front left frame rwyt62-078 Jack-Up Points_005 Greasing About Greasing Since there may be adhesion or damage due to lack of grease on moving parts, they must be greased.
  • Page 104 LM3210A Maintenance Greasing Points No. of Location greasing 　 Type_F points Mower arm fulcrum Grease nipples are installed in the following locations. Lift arm fulcrum Add grease every 50 hours of operation. Brake lever shaft If specified locations, periods and grease are...
  • Page 105 LM3210A Maintenance Mower units #2 and #3 Mower unit #5 ysd2y4-006 ysd2y4-009 Type_F_003 Type_F_006 Lift arm fulcrum Brake lever shaft There is one greasing point on each lift arm There are two greasing points on the brake fulcrum connected to a mower unit.
  • Page 106 LM3210A Maintenance Pivot Neutral position area There are two greasing points on the Middle between the rear wheels neutral position area. ysd2y4-011 8bq62b-223 Type_F_009 Type_F_012 Rear left wheel Reel housing There is one greasing point on the right and left housings of each mower unit.
  • Page 107 LM3210A Maintenance Front roller Caution There is one greasing point on the left and Always use a hand operated grease gun and right of the front roller of each mower unit. only add a maximum of 2 pumps of grease every 50 hours.
  • Page 108 LM3210A Maintenance Cutting reel pivot pins (axis bolts) Type_R Apply 0.5 g (0.001 lb) of urea-based No. 2 grease to the cutting reel pivot pins (axis Grease nipples are installed in the following bolts) mounted on each mower unit every locations.
  • Page 109 LM3210A Maintenance Mower arm fulcrum Mower units #2 and #3 There is one greasing point on each mower arm fulcrum connected to a mower unit. Grease mower units #2 and #3 in the swiveled position. "Swiveling Mower Units #2 and #3" (Page...
  • Page 110 LM3210A Maintenance Traveling pedal shaft fulcrum Rear right wheel There are two greasing points on the traveling pedal shaft fulcrum. 8bq62b-034 Type_R_011 8bq62b-036 Neutral position area There are two greasing points on the Type_R_008 Pivot neutral position area. Middle between the rear wheels...

  • Page 111: Lubrication

    LM3210A Maintenance Reel housing side Cutting reel pivot pins (axis bolts) Apply 0.5 g (0.001 lb) of urea-based No. 2 grease to the cutting reel pivot pins (axis bolts) mounted on each mower unit every 500 hours. 8bq62b-386 Type_R_014 Rear roller There is one greasing point on the left and right of the rear roller of each mower unit.
  • Page 112 LM3210A Maintenance Mower cylinder spherical bearing Lubricating Points There are two points on each mower cylinder. Type_F Mower cylinder #1 Apply lubricant at the following locations every 50 hours of operation. ysd2y4-020 Type_F_002 Mower cylinder #2 and 3 ysd2y4-021 Type_F_003...
  • Page 113 LM3210A Maintenance Steering cylinder spherical bearing Mower cylinder spherical bearing There are two points. There are two points on each mower cylinder. Mower cylinder #1 ysd2y4-023 Type_F_005 ysd2y4-020 Type_R Type_R_002 Apply lubricant at the following locations every Mower cylinder #2 and 3 50 hours of operation.

  • Page 114: Operations Before Maintenance

    LM3210A Maintenance Steering cylinder spherical bearing Swivel the mower unit toward the outside of There are two points. the machine. ysd2y4-023 sibu71-002 Type_R_005 Swiveling Mower Units #2 and #3_002 Fully insert the grip pin into the locking hole Operations Before Maintenance...

  • Page 115: Adjustment And Replacement

    LM3210A Maintenance Insert two or three strips of newspaper into Adjustment and Replacement the space between the reel cutter (cutting cylinder) and the bed knife (bottom blade) at Adjustment of Blade Engagement an angle of 90 degrees. Then, rotate the reel...
  • Page 116 LM3210A Maintenance Use the cutting height gauge to Adjustment of Cutting Height determine the position, then tighten cutting height adjustment nut B securely. Roller (Roller Type) Adjust the cutting height to fit your cutting work. You can adjust the front roller in four stages.
  • Page 117 LM3210A Maintenance Attach the wheel in a position within the range Adjustment of Cutter Adjustment Spring of cutting height that suits your work requirements. If the diameter of the reel cutter (cutting cylinder) becomes smaller, adjust the cutter To increase cutting height: adjustment spring.
  • Page 118 LM3210A Maintenance Select the hold position of the cover Adjustment of Rear Scraper (Wire Type) adjustment plate and secure the reel cover. Note: Adjustment of CR Brush Depending on the specifications, this function Note: may not be available. Depending on the specifications, this function Important may not be available.
  • Page 119 Caution Do not perform back lapping with any other persons. Have the following items ready: Strips of newspaper, Abrasive [Back lapping powder mixed with oil; or gel compound (Baroness genuine abrasive)], Brush. zhz6po-002 Back Lapping_001 Adjustment and Replacement Page 6-19...
  • Page 120 LM3210A Maintenance Check the sharpness of the entire range Newspaper (three or four points) of the reel cutter Back lapping powder (cutting cylinder). Gel compound Using a piece of chalk, mark locations on the Brush blade that are sharp. Shift the reel rotation/stop switching levers of...
  • Page 121 (8.07 in) (3.44 in) (7.28 in) (3.05 in) For sharpening the reel cutter (cutting cylinder), contact your dealer or Baroness Note: unless you have a grinding machine. The outer diameter of the reel cutter (cutting Caution cylinder) shaft is 30 mm (1.18 in).
  • Page 122 LM3210A Maintenance When the reel cutter (cutting cylinder) Reel cutter (cutting cylinder) blade becomes worn and its shape conical, or Reel cutter (cutting cylinder) disc when blade engagement adjustment cannot Reel cutter (cutting cylinder) shaft be performed Outer diameter of reel cutter (cutting...
  • Page 123 LM3210A Maintenance Type_R Replacement of Bed Knife (Bottom Blade) Usage limit Caution Dimension B Dimension B (Distance (Distance Dimension A Dimension A Both the reel cutter (cutting cylinder) and the from blade from blade bed knife (bottom blade) are edged tools.
  • Page 124 LM3210A Maintenance Replacement of Tires Replacement of Rear Tire Replacement of Front Tires Removing rear tires Follow the steps below to remove the rear Removing front tires tire. Follow the steps below to remove the front Loosen the bolts. tires: Loosen the bolts.
  • Page 125 LM3210A Maintenance Be sure to tighten the bolts A and B Adjustment of Belt Tension securely after adjustment. Warning Be sure to stop the engine before adjusting the belts. Important Before making sure of belt tension, rotate the belt several times.
  • Page 126 LM3210A Maintenance Be sure to tighten the bolts A and B Tension pulley adjustment bolt securely after adjustment. Belt Change of Coolant Caution Do not touch the radiator or coolant during engine operation or immediately after the engine has been turned off.
  • Page 127 LM3210A Maintenance Remove the reserve tank. LLC concentration Freezing temperature (volume %) Down to -10 °C (14 °F) 20 % Down to -15 °C (5 °F) 30 % Down to -20 °C (-4 °F) 35 % Down to -25 °C (-13 °F)
  • Page 128 LM3210A Maintenance Remove the drain plug of the hydraulic Change of Hydraulic Oil tank, and then drain the old oil into a container. Caution Wind new sealing tape on the drain plug, Be careful with hot oil, which could cause and then attach it to the hydraulic tank.
  • Page 129 LM3210A Maintenance Check underneath the machine for oil Firmly tighten the filter cartridge by hand leakage. until the packing contacts the mounting surface. Attach the left tank cover. And then tighten it with a half more turn. Change of Hydraulic Oil Filter...
  • Page 130 LM3210A Maintenance Install the intake hose joint fitting to the Change of Hydraulic Oil Suction Filter hydraulic tank. Caution Be careful with hot oil, which could cause burns if it contacts your skin. Important When replacing the hydraulic oil filter, be sure to drain the oil into a container and discard it in accordance with local laws and regulations.
  • Page 131 LM3210A Maintenance Through the oil filling port, supply new Change of Engine Oil engine oil until the oil reaches a level in between the upper and lower limit lines on Caution the oil level gauge. Engine oil quantity is approximately 9.7 dm Be careful with hot oil, which could cause (9.7 L).
  • Page 132 LM3210A Maintenance Make sure that there is no oil leakage at the Replacement of Engine Oil Filter sealing surface of the filter cartridge. Check the engine oil level. Caution If it is low, supply engine oil until it reaches Be careful with hot oil, which could cause the specified level.

  • Page 133: Storage

    LM3210A Maintenance Lightly coat the packing of the new Storage location cartridge with fuel, and then firmly hand- Cover the machine and store it in a dry ･ tighten the cartridge, without using the place where it will not be exposed to rain.
  • Page 134 LM3210A Maintenance Page 6-34 Storage...

  • Page 135: Repair

    LM3210A Repair Precautions for Repair ......Page 7-2 Adjustment and Replacement ....Page 7-2 Adjustment of Brake ......Page 7-2 Adjusting the Neutral Position of the Piston Pump .......... Page 7-4 Change of Fuse ........Page 7-4 Towing ............ Page 7-5 Towing The Machine in An Emergency ..........Page 7-5...

  • Page 136: Precautions For Repair

    Make sure that the lever is maintained in the open position (neutral). Important For each wheel, fully tighten the adjustment Use Baroness genuine parts for replacement bolt on the brake disc side. and accessories. Our product warranty may be void if you use non-genuine parts for replacement or accessories.
  • Page 137 LM3210A Repair Reduce the clearance by loosening the lock Inner wire nut, then tightening the adjustment nut. Adjustment bolt Tighten the adjustment nut until the friction Lock nut material contacts the friction surface of the Connection disc. 1.0 mm (0.039 in)

  • Page 138: Adjusting The Neutral Position Of The Piston Pump

    LM3210A Repair Adjusting the Neutral Position of the Piston Lock nut A (Left-hand thread) Pump Neutral adjustment rod Lock nut B (Right-hand thread) Caution Find the position where the front wheels Make sure not to touch rotating tires. stop, and then tighten the lock nuts.

  • Page 139: Towing

    LM3210A Repair Towing Towing The Machine in An Emergency If the machine does not travel due to engine A B C D E trouble, etc., you can move it by towing it. H I J Caution Before towing, check that the brake is applied effectively.
  • Page 140 LM3210A Repair Front right side Depress the brake pedal to release the parking brake. Warning While towing, always keep your foot on the brake pedal and depress the brake pedal at any time to stop. Tow the machine slowly. gay3t1-025...

  • Page 141: Appended Table

    LM3210A Appended Table Tightening Torques ....... Page 8-2 Standard Tightening Torques ....Page 8-2 Principal Tightening Torques ....Page 8-5 Maintenance Schedule ......Page 8-7 List of Adjusted Value ......Page 8-11 List of Fault Codes ......Page 8-12 Page 8-1...

  • Page 142: Tightening Torques

    LM3210A Appended Table Tightening Torques Important Refer to the Tightening Torque table. Note that the Baroness product warranty may not apply to defects caused by incorrect or overtorque tightening, etc. Standard Tightening Torques Bolts and Nuts Important A number of bolts are used in each part of this machine.
  • Page 143 LM3210A Appended Table General bolt Strength classification 4.8 Nominal diameter tib3yb-001 kgf-cm lb-in 3 - 5 30.59 - 50.99 26.55 - 44.26 7 - 9 71.38 - 91.77 61.96 - 79.66 14 - 19 142.76 - 193.74 123.91 - 168.17 29 - 38 295.71 - 387.49...
  • Page 144 LM3210A Appended Table Hydraulic Hose The tightening torques for union joints and union adaptors with parallel pipe threads (G, PF) are shown in the table below. A union joint or adaptor will not become loose or leak as long as it is tightened by the specified torque.
  • Page 145 LM3210A Appended Table Principal Tightening Torques Tightening Torque by Model LM3210A Tighten the following bolts and nuts at the torque specified in the table. For thread locking adhesive, apply a middle strength thread locker (ThreeBond 1322 or equivalent anaerobic sealant).
  • Page 146 LM3210A Appended Table Tightening torque Thread locking Location Code Part name adhesive kgf-cm lb-in Bolt, w/hexagon hole, K001A100401 815.76 708.08 － M10-40 Joint 458.87 - 398.30 - K0010100352 Bolt, heat-treated M10-35 45 - 76 － 774.97 672.68 530.24 - 460.25 -...

  • Page 147: Maintenance Schedule

    LM3210A Appended Table Maintenance Schedule LM3210A ●・・・Inspect, adjust, supply, clean (first time) ○・・・Inspect, adjust, supply, clean ▲・・・Replace (first time) △・・・Replace Maintenance Item Remarks Check engine oil level ○ 　 　 　 　 　 　 　 　 　 　 　 　 　 　 　...
  • Page 148 LM3210A Appended Table Maintenance Item Remarks Clean inside of CR only if fitted 　 　 　 　 ○ 　 　 　 　 　 　 　 　 　 　 　 　 brush belt cover Check and Adjust 　 　 　 　 ○ 　 　 　 　 　 　 　 　 　 　 　 　...
  • Page 149 LM3210A Appended Table Maintenance Item Remarks whichever comes Check battery fluid level 　 　 　 　 ○ 　 　 　 　 　 　 ○ 　 　 　 　 earlier Adjust fan belt tension 　 　 　 　 ○ 　 　 　 　 　 　 　 　 　 　 　...
  • Page 150 LM3210A Appended Table Maintenance Item Remarks *2.*3.* Replace DPF filters 　 　 　 　 　 　 　 　 　 　 △ 　 　 　 　 　 　 *2.*3.* Check EGR system 　 　 　 　 　 　 　 　 　 　 ○ 　 　 　 　 　...

  • Page 151: List Of Adjusted Value

    *1: When biodiesel fuel is used, change the fuel filter cartridge, fuel hose and clamp bands with new ･ ones at　intervals half of the usual ones. *2: Consult your local Baroness Dealer or　local KUBOTA Dealer　for this service. ･ The items above (*3 marked) are registered as emission related critical parts by KUBOTA in the ･...

  • Page 152: List Of Fault Codes

    LM3210A Appended Table List of Fault Codes Important When the fault code appears in the monitor display, refer to "Kubota DIAGNOSIS MANUAL COMMON RAIL SYSTEM" or contact your dealer. The fault codes (DTC) and corresponding information that appear in the monitor display are listed below.
  • Page 153 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Insufficient output Stop ENG Fuel leak (in - Worsening consumption is To minimize PM Key switch turn...
  • Page 154 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Insufficient output - Worsening exhaust gas Open circuit or +B Stop ENG emissions short circuit of...
  • Page 155 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Engine speed See Service Diagnostic Engine overrun P0219 exceeds - Overrun 　 Manual counter = zero...
  • Page 156 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 (At low temperature) Ground short of Ground short of See Service Key switch turn glow relay...
  • Page 157 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Insufficient output Injector charge Stop ENG voltage: Low Injector charge - Worsening Key switch turn...
  • Page 158 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Faulty starting - Insufficient output Sensor supply Sensor supply See Service Key switch turn - Worsening...
  • Page 159 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Accelerator position sensor Diagnostic Accelerator signal error counter = zero See Service - Insufficient Position Sensor...
  • Page 160 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Insufficient output CAN2 +B or GND See Service Key switch turn CAN2 Bus off U0075...
  • Page 161 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Exhaust gas Open circuit or +B See Service Key switch turn temperature P0544 3242 short circuit of None 　...
  • Page 162 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Differential Ground short See Service Key switch turn pressure P2454 3251 circuit of sensor None 　...
  • Page 163 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Stop engine!! PM accumulation To minimize PM - Insufficient Diagnostic Excessive PM4 Contact dealer P3007 3701...
  • Page 164 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 - Worsening exhaust gas Over heat pre- See Service Diagnostic P3025 523603 15 Coolant temp. 　...
  • Page 165 LM3210A Appended Table Corrective J1939-73 DTC name ISO 14229 Behavior During Recovery from action Detection item Remark Malfunction error Text 1 P-Code Text 2 Loss of DPF See Service Loss of functon of P3015 3936 Function Manual Open Circuit of...
  • Page 166 LM3210A Appended Table Page 8-26 List of Fault Codes...
  • Page 167 1-26, Miyuki-cho, Toyokawa-city, Tel : +81 - 533 - 84 - 1390 Head Office Fax : +81 - 533 - 84 - 1220 Aichi-pref, 442-8530 JAPAN LM3210A-UM--GBZ/23D-00-S.K...

Table of Contents