Wildfire CERALIS User Instructions
  1. Manuals
  2. Brands
  3. Wildfire Manuals
  4. Indoor Fireplace
  5. CERALIS
  6. User instructions

Wildfire CERALIS User Instructions

Hide thumbs Also See for CERALIS:
Table of Contents

Advertisement

Quick Links

CERALIS GAS FIRE
CERALIS XE GAS FIRE
USER INSTRUCTIONS
INSTALLATION INSTRUCTIONS
SERVICE INSTRUCTIONS
It is a regulaon that these instrucons be handed to the customer aer installaon is complete. It is
also the responsibility of the installaon engineer to ensure that the customer is able to fully operate
the appliance and is aware of any cleaning or maintenance requirements.
This product is not suitable for primary heang purposes.
Model numbers: F-011XX1 Manual Control for use on Natural Gas (G20) at a supply pressure of 20 mbar in GB / I.E.
Model numbers: F-011XX2 Slide Control for use on Natural Gas (G20) at a supply pressure of 20 mbar in GB / I.E.
(XX denotes Fuel Bed Type & Trim Type)
P-XX1500 ISSUE7

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CERALIS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Wildfire CERALIS

Summary of Contents for Wildfire CERALIS

  • Page 1  CERALIS GAS FIRE CERALIS XE GAS FIRE USER INSTRUCTIONS INSTALLATION INSTRUCTIONS SERVICE INSTRUCTIONS It is a regulaon that these instrucons be handed to the customer aer installaon is complete. It is also the responsibility of the installaon engineer to ensure that the customer is able to fully operate the appliance and is aware of any cleaning or maintenance requirements.

  • Page 2: Table Of Contents

      CONTENTS Regulatory Informaon and Installaon Requirements …………………………... 3 Installaon Requirements (connued) ………………………………………………….. 4 Sing the Appliance ……………………………………………………………………………… 5 Fixing the Appliance ...………………………………………………………………………...… 7 Connecng the Appliance to the Gas Supply ……………………………………….. 8 Checking Operaon of Appliance ………………………………………………………… 8 Compleng the Installaon ……………………………………………………………………...

  • Page 3: Regulatory InformaOn And InstallaOn Requirements

    REGULATORY INFORMATION AND INSTALLATION REQUIREMENTS  THE FOLLOWING MUST BE NOTED PRIOR TO THE INSTALLATION OF THIS APPLIANCE. This gas appliance MUST be installed by a GAS SAFE registered installer by law. It must be installed in accordance to these installaon instrucons and the GAS SAFETY (Installaon & Use) REGULATIONS 1998 as amended.

  • Page 4: InstallaOn Requirements (ConNued)

    No purpose made venlaon is normally required for this appliance when installed in G.B. If the appliance is being installed in I.E then refer to I.S 813:1996 (Domesc Gas Installaon—Naonal Standards Authority of  Ireland). Venlaon areas (if applicable) should be checked periodically to ensure there is no obstrucon, even though none is normally required for this appliance.

  • Page 5: SiNg The Appliance

    SITING THE APPLIANCE  Fireplace Opening The fireplace opening must be between 405mm and 450mm wide and between 555mm and 570mm high. If the opening intended for the appliance is in excess of these dimensions then a suitable surround must be constructed of non-combusble material to produce an opening within this range of dimensions.
  • Page 6 Installaon into a PRE-CAST FLUE Installaon—connued…  If a dimension of 125mm cannot be achieved to provide such debris collecon then the fire surround can be packed away from the wall—ensuring that that a suitable non combusble material is used and the integrity of the fireplace opening is maintained.

  • Page 7: Fixing The Appliance

    Fixing the Appliance. If the appliance is being installed with a spacer kit, this should be aached to the appliance using the screws included and the second foam length which is supplied with the spacer kit should be affixed to the rear face of the spacer. Do ...

  • Page 8: ConnecNg The Appliance To The Gas Supply

    Connecng the Appliance to the Gas Supply The gas supply can be connected to the appliance by a concealed fing from the rear. In all installaon condions the gas  connecon should be provided using 8mm (O/D) copper tubing. If the concealed installaon method is chosen, there are three oponal entry points at the rear/side of the appliance.

  • Page 9: CompleNg The InstallaOn

    Compleng the Installaon of the Appliance  Remove the protecve covering (if applicable) from the face of the decorave trim. Fit the trim to the appliance with the magnets provided. One magnet should be placed in each corner of the trim at the top of the appliance and on each side about 120mm from the base of the appliance.

  • Page 10: Appliance Technical InformaOn

    Maintenance of the Appliance The following procedures can and should be performed by the customer at regular intervals depending upon use of the  appliance. Appliance Technical Informaon Gas Type : Natural Gas Category : I2H Inlet Pressure: (Cold) 20mbar Heat Input Gross : 6.75kW Injector : 77 Desnaon Countries : GB/ IE...

  • Page 11: Service InstrucOns

    Cleaning the Appliance (connued)  Trim, Fret and Painted Metal Parts There are a variety of trim and fret opons which may have been supplied with your appliance and these are normally a plated material on a steel substrate. It is important that no abrasive cleaners or chemical agents are used in the cleaning of these components.
  • Page 12 Removal / Replacement of Gas Carrying Components (connued) Replacement of the Gas Control Valve  Manual Control Valve Remove the control knob from the valve. Remove the locknut from the front of the valve. Undo the three nuts around the periphery of the valve body—Gas Inlet / Burner / Pilot Remove the thermocouple nut from the back of the valve.

  • Page 13: User InstrucOns

    OPERATING INSTRUCTIONS This appliance is available with two operang methods, namely manual control and slide control. The following  instrucons detail both methods of operaon however the basic operaon of the appliance involves the ignion of a pilot burner (See page 7 for spillage monitoring details—ODS), then the control of the main burner with LOW and HIGH sengs.

  • Page 14: Coal Layout InstrucOns

    FUEL BED LAYOUT (COAL)  The following instrucons detail how the ceramic fuel bed and loose components are to be installed onto the appliance. Great care should be taken when handling these ceramic parts as they are fragile and can easily be broken. Do not force any component into posion, if it does not fit easily then you are not fing the part correctly.
  • Page 15 Step 3  Fit the two side cheeks into posion as shown in the picture below. These are marked L and R for le hand and right hand. Step 4 Carefully place 2 larger coals from the bag marked ’B’ on the front row le and right posions. Place two standard coals from the bag marked ’A’...
  • Page 16 Step 5  Fit three standard coals from bag marked ’A’ into posion as shown in the picture below. Step 6 Fit four standard coals from bag marked ’A’ into posion as shown in the picture below.

  • Page 17: Pebble Layout InstrucOns

    FUEL BED LAYOUT (PEBBLE) The following instrucons detail how the ceramic fuel bed and loose components are to be installed  onto the appliance. Great care should be taken when handling these ceramic parts as they are fragile and can easily be broken. Do not force any component into posion, if it does not fit easily then you are not fing the part correctly.
  • Page 18 Step 3 Fit the two side cheeks into posion as shown in the picture below.  These are marked L and R for le and right hand. Step 4 Carefully place 2 large round pebbles from the bag marked ’A’ on the front row le and right posions. Place two oval pebbles from the bag marked ’B’...
  • Page 19 Step 5 Fit three oval pebbles from bag marked ‘B’ into posion as shown in the picture below.  Step 6 Fit four small pebbles into posion as shown in the picture below.

  • Page 20: Product Fiche

     Product Fiche Manufacturer : Hearth Products Ltd F-011XX1 F-011XX2 Model No. Fuel Type Natural Gas I2H Natural Gas I2H Energy Efficiency Class Indirect Heang Funconality Direct Heat Output kW 3.2kW 3.2kW Indirect Heat Output kW Useful Energy Efficiency (NCV) High : 52.3% High : 52.3% Useful Energy Efficiency (NCV)

  • Page 21: Spare Parts List

    User Replaceable Parts  Part Number Descripon P-XX1101 Ceramic Fuel Bed-Coal P-XX1102 Ceramic Front Rail-Coal P-XX1103 Ceramic Sidecheek LH-Coal P-XX1104 Ceramic Sidecheek RH-Coal P-XX1105 Ceramic Loose Fuel Pack-Coal P-XX1111 Ceramic Fuel Bed—Pebble P-XX1112 Ceramic Front Rail—Pebble P-XX1113 Ceramic Sidecheek LH-Pebble P-XX1114 Ceramic Sidecheek RH-Pebble P-XX1115...
  • Page 22 ...

  • Page 23: Manufacturer's Contact Details

     Hearth Products Ltd Unit 14 Tollgate Industrial Estate, Stafford, ST16 3SU Www.hearthproducts.co.uk Tel: 01785 225401 Fax: 01785 225501 Email: info@hearthproducts.co.uk Due to our policy of connual product improvement, some diagrams and small details may not be accurate however if there is any concern or maer of understanding that you feel needs to be clarified please contact us directly.

This manual is also suitable for:

Ceralis xe

Table of Contents