Subscribe to Our Youtube Channel
Related Manuals for Linde Ryval 40 PLASMA PFC ovo
Summary of Contents for Linde Ryval 40 PLASMA PFC ovo
- Page 1 PLASMA CUTTING MACHINE Ryval 40 PLASMA PFC ovo OPERATING MANUAL Linde AG, Linde Gas Deutschland © 2015 Ryval 40 PLASMA PFC ovo Manual EN 1...
-
Page 2: Table Of Contents
REQUIREMENTS FOR SOURCE OF COMPRESSED AIR ....15 OPTIONAL AIR FILTERS ..............15 CUTTING ..................16 IMPORTANT RULES ................ 17 SOURCES OF POOR QUALITY CUTS ..........17 MAINTENANCE ..................18 STATEMENT OF WARRANTY .............. 19 DISPOSAL ..................... 20 © Linde AG, Linde Gas Deutschland... -
Page 3: Introduction
Manual represents the Manufacturer's best judgement, the Manufacturer assumes no liability for its use. Machine Ryval 40 PLASMA PFC ovo is designed for cutting metal on the basis of modern technology cutting material through a thin beam plasma gas. -
Page 4: Safety Instructions And Warnings
The kinds of fumes and gases from the plasma arc depend on the kind of metal being used, coatings on the metal, and the different processes. You must be very careful when cutting or welding any metals which may contain © Linde AG, Linde Gas Deutschland... - Page 5 In our generator this voltage is 380V. The maximum open-circuit voltage of the plasma machines is established © Linde AG, Linde Gas Deutschland...
-
Page 6: Electromagnetic Compatibility (Emc)
Pacemakers and hearing aids. All very sensitive electrical equipment. 2. The operator is responsible for the installation and use of the cutting machine. If there should be any fault in operations of other systems located © Linde AG, Linde Gas Deutschland... -
Page 7: Protective Uttilities
4. Place the machine the way that the cooling air can enter the vents without restriction to. It is necessary to ensure that no impurities, especially metal particles, are not drawn into the machine. 5. Cutting machine in terms of interference suppression is intended primarily © Linde AG, Linde Gas Deutschland... -
Page 8: Technical Data
Copper Working pressure Max. Input pressure Air consumption l/min Arc ignition pneu-mechanic Curent regulation Continuous Protection IP 23S Standards EN 60974-1 Dimensions (w x l x h) 215 x 470 x 387 Weight 16,8 © Linde AG, Linde Gas Deutschland... -
Page 9: Operator Controls
2. LED illuminates and the air valve regularly opens and closes - the cutting tip and the electrode are not fitted properly. 3. LED flashes – there is not shield cup or the shield cup is © Linde AG, Linde Gas Deutschland... -
Page 10: Accessories
742.D121.1 Circular Cutting Attachment ABICUT 45 5302 Air filter AT 1000 5304 Set for filter AT 1000 S777a Light Reactive Welding Helmet ALFA IN S777 Fig. 2 Circular Cutting Attachment Fig. 3 Air filter AT 1000 ABICUT 45 © Linde AG, Linde Gas Deutschland... - Page 11 Shield Cup, 6 holes, max. life SCP2551 Cutting Buggy SCP 60 SCP2540 Double Pointed Spacer SCP 60 Note – the bold items are equipped on the torch Recommended starting kit for the Torch SCP 60 Pos. Item No Description © Linde AG, Linde Gas Deutschland...
- Page 12 Electrode Long ABI25/45 748.0033.2 Air diffuser ABI25/45 748.0034.10 Cutting Tip 0,65 Standard ABI25/45 748.0035.10 Cutting Tip 0,8 Standard ABI25/45 748.0061.10 Cutting Tip 1,0 Standard ABI25/45 748.0049.10 Cutting Tip 0,9 Long ABI25/45 748.0052.2 Shield Cup ABI 45-35A © Linde AG, Linde Gas Deutschland...
-
Page 13: Comments On Consumables
2. It is possible to drag the Long cutting tip directly on the cutting material up to thickness of 5.8 mm without the guiding spring. The Lifetime of the cutting tip and the electrode is reduced by 30% - 50%. 2.2.3 Standard electrode and standard cutting tips © Linde AG, Linde Gas Deutschland... -
Page 14: First Steps
4 bar. 8. Set potentiometer pos 3 to the cutting power you need. 9. Fit the torch with appropriate type of cutting tip electrode and shield cup according to the selected cutting current. © Linde AG, Linde Gas Deutschland... -
Page 15: Requirements For Source Of Compressed Air
To achieve high quality cutting and to avoid serious disturbances to the torch it is highly advised to include the air filter. Pos. Item No Description 5302 Air filter AT 1000 5304 Set for filter AT 1000 © Linde AG, Linde Gas Deutschland... -
Page 16: Cutting
3 mm. 7. In case of cutting in the corner or around the corner (see Figure 7), use the long electrode and cutting tip (pos. 17 and 20). The cutting power while © Linde AG, Linde Gas Deutschland... -
Page 17: Important Rules
7. Ryval 40 PLASMA PFC is adapted for use with torch ABICUT 45. This combination comply with EN 60974-7 Article 10.1.4. Using any other type and design of a torch must be approved by Linde AG, Linde Gas Deutschland . -
Page 18: Maintenance
2. To clean the plasma cut, disconnect it from the mains supply voltage then open the enclosure and use a vacuum cleaner to remove any accumulated dirt and dust. The plasma cut should also be wiped clean. If necessary, © Linde AG, Linde Gas Deutschland... -
Page 19: Statement Of Warranty
3. Linde AG, Linde Gas Deutschland will repair or replace, at its discretion, any warranted parts or components that fail due to defects in material or workmanship within the warranty period. -
Page 20: Disposal
20/20 distributor or an Authorised Service Agent approved by the company Linde AG, Linde Gas Deutschland DISPOSAL Only for EU countries. Do not dispose of electric tools together with household waste material. In accordance with European Council Directive 2002/96/EC on...
Need help?
Do you have a question about the Ryval 40 PLASMA PFC ovo and is the answer not in the manual?
Questions and answers