Page 2
BOC Smootharc Advance III MIG 225C & 255C Operating manual Welcome to a better way of welding. This operating manual provides the basic knowledge required for MIG Welding, as well as highlighting important areas of how to operate the Smootharc ADVANCE machines.
BOC Smootharc Advance III MIG 225C & 255C Operating manual Contents. 1.0 Recommended Safety Guidelines and Precautions 9.0 Warranty Information Health Hazard Information Terms of Warranty Personal Protection Limitations on Warranty Cylinder Safety Warranty Period Electrical shock Warranty Repairs User Responsibility 10.0 MIG Process...
BOC Smootharc Advance III MIG 225C & 255C Operating manual 1.0 Recommended Safety Guidelines and Precautions Diagram and safety explanation Electrical safety alert Welding electrode causing electric shock Fumes and gases coming from welding process Some safety precautions BOC recommends are as follows: Welding arc rays →...
BOC Smootharc Advance III MIG 225C & 255C Operating manual Health Hazard Information stainless steel, nickel, nickel alloys or galvanised steel, further precautions are necessary. The actual process of MIG welding is one that can cause a variety of hazards.
BOC Smootharc Advance III MIG 225C & 255C Operating manual Cylinder Safety Cylinder valve hand-wheel Back-plug Bursting disc Back view of typical cylinder valve Operator wearing personal protective equipment (PPE) in safe position Before operating a cylinder valve Ten points about cylinder safety Ensure that the system you are connecting the cylinder into is suitable for the gas and pressure involved.
BOC Smootharc Advance III MIG 225C & 255C Operating manual Electrical shock BOC stock a huge range of personal protective equipment. This combined with BOC’s extensive Gas and Gear network ensures fast, reliable service → Never touch ‘live’ electrical parts throughout the South Pacific.
BOC Smootharc Advance III MIG 225C & 255C Operating manual Switch on to electrical safety for single-phase equipment BOC welding machines are designed and manufactured to conform to IEC 60974 or AS 60974. This Standard not only covers the machine but also the input cable and plug requirements including the size of the plug that should be used.
Page 9
BOC Smootharc Advance III MIG 225C & 255C Operating manual How important is the correct input cable and plug on a welding machine? The size of the plug depends on a formula that to understand input and output currents and to...
BOC Smootharc Advance III MIG 225C & 255C Operating manual 2.0 Package Contents MIG 225C Package Contents MIG 255C Package Contents ✓ ✓ Power source with 15A input cable Power source with 15A input cable and and plug plug fitted for demonstration and 32A input cable and plug unfitted ✓...
BOC Smootharc Advance III MIG 225C & 255C Operating manual 3.0 Technical Specifications Specifications 225C 255C Part No. ADVANCEIII225C ADVANCEIII255C Main Voltage Single Phase AC240V±15% Single Phase AC240V±15% Frequency 50/60Hz 50/60Hz Rated input current (I ) (A) 14.6 13.3 13.5 27.2...
BOC Smootharc Advance III MIG 225C & 255C Operating manual 4.0 Quick Overview IMPORTANT Front and back of power source 225C & 255C The 225C and 255C machines come fitted with a 15A rated single phase plug. The 255C machine also includes a 32A plug for compliance to AS/NZ electrical regulations.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 5.0 Installation Installation for MIG/MAG process 8 For torch positive (DCEP), plug the short mechanical connector (link plug) IMPORTANT on the front panel into the positive (+) terminal and the work return lead into the negative (–) terminal...
BOC Smootharc Advance III MIG 225C & 255C Operating manual Installation for TIG process Installation for MMA process 5.2 Installation for TIG process 5.3 Installation for MMA process 1 Connect the TIG torch power into the negative (–) terminal to be DCEN.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 6.0 Control panel Home Screen – Screen showing welding parameters and job mode Ar CO 0.80 16.5 m/min SAVE Main functions Wire Inch Button Gas Test Button Back Button Adjusting Knob - Left...
BOC Smootharc Advance III MIG 225C & 255C Operating manual 6.4 Main Settings (Welding parameters) In the Home Screen, select the welding mode through the left knob, rotate the right knob, select Main SET, and then press the right to enter this screen.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 6.5 Second Settings screen (Level 2 parameters) Please refer to Section 6.8 on following page for a trigger latch NOTE Available in synergic mode only, need to select explanation. ‘Synergic mode’ to access ‘Second Settings’ screen.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 6.6 JOB Screen In the Main SET/Welding screen of MIG mode, long press (5 seconds left knob to pop up SELECT JOB dialog box. As shown in the figure below. Selecting JOB 1.
BOC Smootharc Advance III MIG 225C & 255C Operating manual Service Screen In the Home Screen, select the MIG/SYN mode through left knob, rotate right knob, select Main SET, and then press right knob to enter the MIG/ SYN welding screen.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 6.11 Gas Test Screen 1. Short press the Gas Test Button the system will START gas testing 2. Short press the Gas Test Button again to STOP gas testing. The GAS TEST will be displayed on the LCD screen, and it will flash continuously, as shown in the figure below.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 7.0 Operating your machine Operation Instructions for MIG Starting up Setting second parameters Turn the power switch to the ON position. In the Home Screen, turn the Right knob to select Second SET, and then press Right knob to confirm to enter the Second SET Screen.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 7.1.1 Inductance 7.1.2 4T/2T Trigger Latch Selection Inductance in welding is the control of current surges during short circuits. On all MIG machines there is no current or wire feed until the trigger on the The wire touches the weld pool 50 to 150 times per second.
BOC Smootharc Advance III MIG 225C & 255C Operating manual Operation instruction of TIG Operation instruction of MMA Starting up Starting up Turn the power switch to the ON position. Turn the power switch to the ON position. Connections Connections Connect TIG torch to the negative (–) terminal.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 8.0 Periodic Maintenance & Troubleshooting The working environment and amount of use the machine receives should be taken into consideration when planning maintenance frequency of your Smootharc Advance III welder.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 9.0 Warranty Information Terms of Warranty Warranty Period The Smootharc ADVANCE III machine has a limited warranty that covers The warranty is valid for 5 years from date of purchase provided the machine manufacturing and material defects only.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 10.0 MIG Process Typical MIG set up Torch Torch trigger Shroud Gas diffuser Contact tip Welding wire Shielding Weld Droplets Weld pool 10.1 Introduction to Metal Inert Gas (MIG) dioxide shielding gas, or using self-shielding flux-cored wire, requiring no shielding gas.
Page 28
BOC Smootharc Advance III MIG 225C & 255C Operating manual Extended self shielded flux cored wire nozzle In terms of gas shielding, there are two different ways in which this may be To bring the welding current back to 250 amps it is necessary to increase the achieved with the FCAW process.
BOC Smootharc Advance III MIG 225C & 255C Operating manual Process Schematic Diagram for MIG / FCAW and MCAW Gas hose Continous wire Wire feed unit Power cable Torch conduit Gas cylinder Welding torch Workpiece Earth clamp Power source Return cable If no external gas shield is required, then the flux fill must provide sufficient specific product being used.
Page 30
BOC Smootharc Advance III MIG 225C & 255C Operating manual Schematic of Dip Transfer Short circuit Necking Arc re-ignition Arc established Arc gap shortens Short circuit Time Current (A) Voltage (V) Short circuit cycle Arcing cycle Modes of Metal Transfer Metal-cored wires transfer metal in dip mode at low currents just like solid MIG wires.
BOC Smootharc Advance III MIG 225C & 255C Operating manual Schematic of Globular Transfer Schematic of Spray Transfer Gas shroud Shielding gas Wire Droplets Weld Splatter Large droplet Workpiece Workpiece 10.4 Fundamentals of MIG, FCAW and MCAW The current flows continuously because of the high voltage maintaining a long arc and short-circuiting cannot take place.
Page 32
BOC Smootharc Advance III MIG 225C & 255C Operating manual Typical Metal Transfer Mode Cast and Helix Globular Spray Transfer Transfer Transfer Process Cast Metal Inert Gas ✓ ✕ ✓ Helix (MIG) Flux Cored ✓ ✓ ✓* (Gas Shielded) Cast – Diameter of the circle Flux Cored ✓...
Page 33
BOC Smootharc Advance III MIG 225C & 255C Operating manual Selection of the Correct Shielding Gas The selection of the shielding gas has a direct influence on the appearance and quality of the weldbead. The thickness of the material to be welded will determine the type of shielding gas that has to be selected.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 11.0 Gas tungsten arc welding (GTAW/TIG) Schematic of the TIG welding process Collet Shielding gas Tungsten electrode TIG filler rod Weld pool Workpiece 11.1 Introduction The Tungsten Inert Gas, or TIG process, uses the heat generated by an...
BOC Smootharc Advance III MIG 225C & 255C Operating manual 11.3 Process variables Process variable Explanation Usage DCEN When direct-current electrode-negative (straight polarity) For a given diameter of tungsten electrode, higher Narrow bead, is used: amperage can be used with straight polarity. Straight deep penetration...
BOC Smootharc Advance III MIG 225C & 255C Operating manual 11.4 Shielding gas selection 11.5 Welding wire selection The following table includes the recommended welding consumable for Material Shielding gas Benefits the most commonly welded materials. Brass Argon Stable arc Base material...
BOC Smootharc Advance III MIG 225C & 255C Operating manual 11.6 Tungsten electrode selection Thickness Welding Base metal type range Desired results current Electrode type Shielding gas Tungsten performance characteristics Copper alloys, General purpose DCSP 2% Thoriated 75% Argon/ Best stability at medium currents. Good arc...
Page 38
BOC Smootharc Advance III MIG 225C & 255C Operating manual Tungsten electrode tip shapes and current ranges Tungsten tip preparation Thoriated, ceriated, and lanthanated tungsten electrodes do not ball DCSP (EN) or DCRP (EP) ACHP General Purpose as readily as pure or zirconiated tungsten electrodes, and as such are typically used for DCSP welding.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 11.7 Welding techniques 11.8 Torch movement during welding TIG Welding techniques Tungsten Without Filler Rod Tungsten With Filler Rod Welding direction Welding Vertical 75° direction Welding Rod 60–75° Form pool Form pool 75°...
Page 42
BOC Smootharc Advance III MIG 225C & 255C Operating manual Condition Result Long arc length Undercut Porosity Wide bead profile Loss of gas Acute angle coverage Oxides Unsymmetrical bead Angular profile mis-alignment Incomplete Mis-alignment penetration Filler rod removed from gas shield...
BOC Smootharc Advance III MIG 225C & 255C Operating manual 12.0 MMA Process Schematic of MMA process in operation 12.1 Process 12.2 Welding Machine Manual Metal Arc welding is the process of joining metals where an electric The most important consideration when contemplating the use of arc welding arc is struck between the metal to be welded (parent metal) and a flux- for the first time is the purchase of a suitable welding machine.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 12.3 Welding Technique operating qualities which appeals to the beginner and experienced operator alike. Successful welding depends on the following factors: Electrodes and Typical Applications → selection of the correct electrode...
Page 45
BOC Smootharc Advance III MIG 225C & 255C Operating manual Electrode Size current, set on the current range specified. The limits of this range should not normally be exceeded. The size of the electrode is generally dependent on the thickness of the...
BOC Smootharc Advance III MIG 225C & 255C Operating manual Layers Weld Beads Butt Welding Electrode Angle for 1st and 2nd Layers Electrode Angle for Subsequent Layers Face Reinforcement Weld Face Layers Weld Beads Layers Weld Beads Root Face Root Gap...
Page 47
BOC Smootharc Advance III MIG 225C & 255C Operating manual Welding Progression Angle General notes on Butt Welds Double ‘V’ Butt Weld The first run in a prepared butt weld should be deposited with an electrode Used on plate of 12 mm and over in thickness when welding can be applied from both sides.
BOC Smootharc Advance III MIG 225C & 255C Operating manual Slag Inclusions Undercutting Lack of Fusion Correct selection of electrodes is important for vertical welding. → letting slag run ahead of the arc. In overhead fillet welds, careful attention to technique is necessary to obtain This defect can be prevented by: a sound weld of good profile.
Page 51
BOC Smootharc Advance III MIG 225C & 255C Operating manual Lack of Fusion Lack of fusion is when the weld metal is not fused to the base metal. This can occur between the weld metal and the base metal or between passes in a multiple pass weld.
BOC Smootharc Advance III MIG 225C & 255C Operating manual 14.0 Correct Application Techniques Electrical stickout Contact Tube Setback Standoff Distance Visible Stickout Arc length Electrical Stickout Gas Nozzle Contact Tube Consumable Electrode Workpiece Correct Application Techniques Flux cored welding with cored wires takes place normally with the drag technique.
Page 55
BOC Smootharc Advance III MIG 225C & 255C Operating manual Electrical stickout Travel speed Short Normal Long Slow Normal Fast Slow Normal Fast Short Normal Long Electrical stickout The electrical stickout is the distance between the end of the contact tip and the end of the wire.