Related Manuals for Linde RYVAL 200 MIG MAN PFC
Summary of Contents for Linde RYVAL 200 MIG MAN PFC
- Page 1 WELDING MACHINE RYVAL 200 MIG MAN PFC OPERATING MANUAL Linde AG, Linde Gas Deutschland. © Ryval 200 MIG MAN PFC Manual EN 04...
-
Page 2: Table Of Contents
OPERATOR CONTROLS ................8 GETTING STARTED MIG/MAG .............. 12 GETTING STARTED TIG ................ 18 GETTING STARTED MMA ..............19 ROUTINE MAINTENANCE & INSPECTION ..........19 10. STATEMENT OF WARRANTY .............. 20 11. DISPOSAL ..................... 21 Linde AG, Linde Gas Deutschland ©... -
Page 3: Introduction
Manual represents the Manufacturer's best judgement, the Manufacturer assumes no liability for its use. The model of RYVAL 200 MIG MAN PFC is the multi-function inverter power generators welding by those methods MIG/MAG in 2T, 4T, wires SG2 or stainless steel 0,6 - 1,0 mm, Al wires 1,0 mm, flux cored wires shelf shielding or standard. -
Page 4: Safety Instructions And Warnings
The operator must NEVER weld containers that have previously contained petrol, lubricants, gas or similar flammable materials, even if the container has been empty for a considerable time. THERE IS A VERY HIGH RISK OF EXPLOSION. Linde AG, Linde Gas Deutschland ©... - Page 5 The welding machines of this type can be marked with the symbol: Before opening the machine switch off the machine and disconnect it from the power socket. Linde AG, Linde Gas Deutschland ©...
-
Page 6: Technical Data
40%=200 (DC=x%) I Protection IP 23S Standards EN 60974-1; EN 60974-10 class A Dimensions (w x l x h) 251x540x395 generator Weight 16,5 Linde AG, Linde Gas Deutschland continuously strives to produce the best Linde AG, Linde Gas Deutschland ©... -
Page 7: Equipment
4. EQUIPMENT MODELS Item No Description 5.G-19 RYVAL 200 MIG MAN PFC ACCESSORIES TO ORDER Item No. Description VM0253 Welding Cable Set 2x 3m 35-50 160A 5.0156 Roll 0.6-0.8/1.0 RYVAL MIG 4281 Valve Red.AR /CO2, 2 manometers,MINI... -
Page 8: Operator Controls
8/21 5. OPERATOR CONTROLS Fig. 1. RYVAL 200 MIG MAN PFC Pos. Description Control panel Handle Gas connector for TIG torch (-) terminal of welding cables TIG torch connector Central MIG/MAG torch connector TIG torch control connector (+) terminal of welding cables... - Page 9 LED. If it lights the display 23 shows the time of down slope LED. If it lights the display 23 shows the voltage LED. If it lights display 23 shows the value of ARC FORCE Linde AG, Linde Gas Deutschland ©...
- Page 10 OFF – of the remote control Switch Spool Gun. In the ON position one can weld with the Spool Potentiometer for the Burnback time setting Potentiometer for the initial wire speed setting Potentiometer for the Pre Gas time setting Linde AG, Linde Gas Deutschland ©...
- Page 11 Pressure arm Inlet liner EURO connector Roll OVERVIEW OF ROLLS FOR WIRE FEED a = 22 mm b = 30 mm Groove type Wire diameter Item No 0,6-0,8 2187 Steel 0,8-1,0 2188 0,8-1,0 2270 Aluminum Linde AG, Linde Gas Deutschland ©...
-
Page 12: Getting Started Mig/Mag
Getting started must be consistent with technical data and conditions of use. CHOOSING THE FEEDING ROLL In all machines (Linde AG, Linde Gas Deutschland MIG / MAG) rolls with two grooves are used. These grooves are intended for two different wire diameters (e.g. - Page 13 Fig. 7 Connecting the ground cable and the torch 1. Connect the torch B6 to connector B8 on the machine while the machine is turned off. 2. Connect the ground cable to the terminal of welding cables (-) B4 Linde AG, Linde Gas Deutschland ©...
- Page 14 10-15l/min. 4. After long-term shutdown of the machine or replacement of the torch it is suitable to blow the pipes with protective gas before welding. Fig. 8 - Gas flow setting Linde AG, Linde Gas Deutschland ©...
- Page 15 Table of approximate parameter settings ADJUSTING THE MACHINE FOR ANOTHER WIRE DIAMETER In all machines Linde AG, Linde Gas Deutschland MIG / MAG are used rolls with two grooves. These grooves are intended for two different wire diameters (e.g. 0,8 a 1,0 mm). Groove can be replaced by removing the rolls and rotating them, or use a different roll grooves with required dimensions.
- Page 16 6. Connect the ground cable to the (+) panel socket, fig. 1, pos. 7. Fig. 9 Terminals for changing the polarity of the MIG/MAG torch Pos. Description Upper terminal (+) Bridge Middle terminal Lower terminal (-) Linde AG, Linde Gas Deutschland ©...
- Page 17 Fig. 10 Customization of the feed for the aluminium wire Pos. Description EURO connector Rolls Liner terminal for 4,0mm, 4,7mm outer diameter O-ring 3,5 x1, 5mm to prevent escape of gas Liner tefl. Sustain pipe for teflon and plastic liner Linde AG, Linde Gas Deutschland ©...
-
Page 18: Getting Started Tig
Slope down. 8. By means of the potentiometers 36 you can change the time of Gas. 9. By means of the potentiometers 37 you can change the time of Post Gas. Linde AG, Linde Gas Deutschland ©... -
Page 19: Getting Started Mma
Welder. If these parts are damaged for any reason, replacement is recommended. CAUTION Do not blow air into the welder during cleaning. Blowing air into the welder can cause metal particles to interfere with sensitive electronic components and cause damage to the welder. Linde AG, Linde Gas Deutschland ©... -
Page 20: Statement Of Warranty
3. Linde AG, Linde Gas Deutschland will repair or replace, at its discretion, any warranted parts or components that fail due to defects in material or workmanship within the warranty period. The warranty period begins on the date of sale to the end user. -
Page 21: Disposal
NOTE Warranty repairs must be performed by either an Linde AG, Linde Gas Deutschland Service Centre, an Linde AG, Linde Gas Deutschland distributor or an Authorised Service Agent approved by the company Linde AG, Linde Gas Deutschland.
Need help?
Do you have a question about the RYVAL 200 MIG MAN PFC and is the answer not in the manual?
Questions and answers