Related Manuals for Linde RYVAL 60 PLASMA
Summary of Contents for Linde RYVAL 60 PLASMA
- Page 1 PLASMA CUTTING MACHINE RYVAL 60 PLASMA OPERATING MANUAL Linde AG, Linde Gas Deutschland © RYVAL 60 PLASMA manual EN 06...
-
Page 2: Table Of Contents
TECHNICAL DATA ..................8 MAIN PARTS OF THE MACHINE .............. 9 ACCESSORIES ..................11 GETTING STARTED ................13 CUTTING ....................15 MAINTENANCE ..................18 10. STATEMENT OF WARRANTY ..............19 11. DISPOSAL ....................20 Linde AG, Linde Gas Deutschland ©... -
Page 3: Introduction
Machine RYVAL 60 PLASMA is designed for cutting metal on the basis of modern technology cutting material through a thin beam plasma gas. RYVAL 60 PLASMA is designed for high-quality cutting of materials up to 25 mm thick carbon steel (for more information, see instructions below). Productive... -
Page 4: Safety Instructions And Warnings
The kinds of fumes and gases from the plasma arc depend on the kind of metal being used, coatings on the metal, and the different processes. You must be very careful when cutting or welding any metals which may contain Linde AG, Linde Gas Deutschland ©... - Page 5 In our generator this voltage is 310V. The maximum open-circuit voltage of the plasma machines is established by national and international standards (EN 60974-1) depending on the type Linde AG, Linde Gas Deutschland ©...
- Page 6 3. Welding apron and cloth 4. Welding boots RISK OVERVIEW 1. Risk of electric shock. 2. Ultraviolet light and light radiation 3. Risk of inhaling gas fumes and dust particles 4. Burns 5. Noise Linde AG, Linde Gas Deutschland ©...
-
Page 7: Conditions Of Use
7/20 NOTE The Machine Torches (AUT) must not be used with RYVAL 60 PLASMA. It may only be used together with RYVAL 60 PLASMA CNC. NOTE 1. It is forbidden to operate a machine with damaged insulation of the cutting torch or supply cable. -
Page 8: Technical Data
Cutting current (DZ=100%) I Cutting current (DZ=60%) I Cutting current (DZ=90%) I 90%=65 Max. productive cutting thickness – carbon steel Max. cutting thickness – carbon steel Carbon steel Stainless steel Quality cutting thickness Aluminium Copper Working pressure Linde AG, Linde Gas Deutschland ©... -
Page 9: Main Parts Of The Machine
Picture 1 – The main parts Pos. Description Quick connector - earthing cable Connector - remote control – in standard doesn’t work – only on request Connector - torch Potenciometer - set cut current Linde AG, Linde Gas Deutschland ©... - Page 10 Switch Setting of gas flow Continuous cutting Cutting material with gaps – Caution! Higher wear of nozzles and electrodes Manometer Gas fitting Controler Mains cable Switch ON/OFF Linde AG, Linde Gas Deutschland ©...
-
Page 11: Accessories
Adapter for AT 1000 PEGAS PLASMA S777c. Welding Helmet Barracuda S777C Black 7037 Torch Plasma SVH-105 hand 75° 7042 Cable Package 6,0 m SV-125 6 PIN 7101 Silicone Lubricant Brutto 6 g 7102 Silicone Lubricant Brutto 9 g Linde AG, Linde Gas Deutschland ©... - Page 12 Shield Cup body 80-105A SVH/SVM-105 7073 Shield Cup 20-70A SVH-105 7072 Shield Cup 85-105A SVH-105 7074 Tip gouging 45A SVH-105 (pkg.10) 7075 Tip gouging 70A SVH-105 (pkg.10) 7000 Tip TM-105, SVH/SVM-105 (pkg.10) 7001 Tip 105A TM-105, SVH/SVM-105 (pkg.10) Linde AG, Linde Gas Deutschland ©...
-
Page 13: Getting Started
7. Connect the mains plug to the mains socket. 8. After turning on the ON/OFF switch A14 the display A5 will illuminate. 9. Connect the work lead cable to the material being cut and to the connector A1. Linde AG, Linde Gas Deutschland ©... - Page 14 Pos. Item No Description 5302 Air filter AT 1000 5304 Set for filter AT 1000 to RYVAL Plasma NOTE Max. allowable pressure of filter AT 1000 is 8,5 bar. Linde AG, Linde Gas Deutschland ©...
-
Page 15: Cutting
4. To achieve a good cutting quality make sure the distance between the tip and Linde AG, Linde Gas Deutschland ©... - Page 16 6. Unplug the machine from the mains before any intervention inside the machine. 7. RYVAL 60 PLASMA is adapted for use with torch Plasma SVH-105. This combination comply with EN 60974-7 Article 10.1.4. Using any other type and design of a torch must be approved by Linde AG, Linde Gas...
- Page 17 2. Damaged cutting tip and electrode 3. The position of the torch is not perpendicular to the material. 4. Too large distance from the cutting tip to the material. Max 15 Picture 6 Picture 7 Picture 8 Linde AG, Linde Gas Deutschland ©...
-
Page 18: Maintenance
8. The person carrying out the servicing needs and repairs must know what to look at, what to look for and what to do. Linde AG, Linde Gas Deutschland ©... -
Page 19: Statement Of Warranty
3. Linde AG, Linde Gas Deutschland will repair or replace, at its discretion, any warranted parts or components that fail due to defects in material or workmanship within the warranty period. -
Page 20: Disposal
20/20 4. If warranty is being sought, please contact your Linde AG, Linde Gas Deutschland product supplier for the warranty repair procedure. 5. Linde AG, Linde Gas Deutschland warranty will not apply to: a) Equipment that has been modified by any other party other than Linde AG, Linde Gas Deutschland’s own service personnel or with prior...
Need help?
Do you have a question about the RYVAL 60 PLASMA and is the answer not in the manual?
Questions and answers