Anti-corrosive agents are kind to the tools for pulling the flywheel. environment and degrade fast. Using ecologically safe bio-lubricants and bio-anti-corrosives, you contribute to environmental protection and to the wellbeing of humans, animals and plants. agria Hydrostatic Tool Carrier 5900 Bison...
-20°C app. - 9°C As a last resort, you can add up to 30% of regular petrol to avoid paraffine de- posits. However, this has negative ef- fects on consumption rate and performance. agria Hydrostatic Tool Carrier 5900 Bison...
Due use includes compliance with agria Hydrostatic Tool Carrier 5900 Bison...
Page 9
Never adjust the operating handles dur- For operation in enclosed areas, ensure ing work – danger! that a safety distance is kept to enclo- sures to prevent damage to tools. agria Hydrostatic Tool Carrier 5900 Bison...
Page 10
Secure tool carrier against unauthorized Do not transport the dismounted cutter use. If tool carrier is equipped with igni- bar without knife guards. tion key, remove the key. For all other versions, remove spark plug connector. agria Hydrostatic Tool Carrier 5900 Bison...
Page 11
For grinding the mowing knives, always Only use original agria spare parts. All wear safety goggles and gloves. other commercial spare parts must cor- Weights respond to quality and technical require- ments specified by agria.
Page 12
Any repairs are to be carried out by Dispose of oil, greases, and filters trained mechanics only and with the seperately and properly. appropriate tools. Regularly check tyre air pressure. Ex- cessive pressure may cause bursts. agria Hydrostatic Tool Carrier 5900 Bison...
Page 13
Persons having a pacemaker may not touch live parts of the ignition system Signs when the engine is running. When working with the machine, wear individual protective ear plugs. Wear protective gloves. Wear solid shoes. agria Hydrostatic Tool Carrier 5900 Bison...
Air filter: ..Dry filter element with Engine is suited for use on slopes foamed preliminary filter (oil level at “max” = upper mark) and cyclone pre-separator Continuous operation possible up to ....20° inclination (37 %) agria Hydrostatic Tool Carrier 5900 Bison...
3. Devices and Operating Elements The tool carrier agria type 5900 Bison Even after break-in period never use is a base power machine and is always engine at higher speed than necessary operated with an implement mounted. for the work in hand.
Position “I” = Operation Position “0” = Engine off The engine shut-off switch also serves to shut off the engine in an emergency situation. Set the switch to “0” for fast shut-off. agria Hydrostatic Tool Carrier 5900 Bison...
Do not fasten safety circuit lever. The safety circuit lever also serves to shut off the engine in an emergency. Release the safety circuit lever for fast engine shut-off. The lever automatically goes to STOP position. agria Hydrostatic Tool Carrier 5900 Bison...
PTO-Shaft Connection The speed-independent PTO (A/22) is connected with a connection mechanism (B/7). With the connection mechanism drawn backwards, the PTO-drive is con- nected, when slid forwards, the PTO-drive is disconnected. agria Hydrostatic Tool Carrier 5900 Bison...
3. Devices and Operating Elements Transmission The agria tool carrier is equipped with a hydrostatic drive. Setting the Driving Speed and Direction Lever shift model The driving speed forward or reverse is steplessly set or changed with the forefinger or the thumb at the driving lever (B/10).
When the lock is opened, the hydraulic steering is connected again. Use: Operation at the slope! – similar to a differential lock! or for lifting out an implement. agria Hydrostatic Tool Carrier 5900 Bison...
Pull ball handle (B/1) upwards and keep it in position; then turn steering handle to the left or right into the desired position. Release ball handle and slightly move steering hand- le to the left and right until the fixing bolt is engaged. agria Hydrostatic Tool Carrier 5900 Bison...
3490 411 20x8.00-10 grass tyre grass maintenance 3490 511 21x11.00-8 terra tyre general maintenance 3490 611 23x8.5-12 wide-track field tyre general maintenance 5990 611 23x10.5-12 wide-track field tyre general maintenance 5990 711 agria Hydrostatic Tool Carrier 5900 Bison...
Page 27
4 Track-width adjuster (item 5519 031) 10 Ball spring washer Drive-Wheels for Slopes 11 Wheel bolt It is recommended to use twin wheels or strake wheels for mow- ing areas on extremely steep slopes. agria Hydrostatic Tool Carrier 5900 Bison...
20 mm Min. clearance to attachment drive wheels 20 mm! Pull ball handle lever Ball handle lever must not point downward Press ball handle lever axially inward - until it unlocks - and turn upward agria Hydrostatic Tool Carrier 5900 Bison...
Tighten cap nuts evenly. For PTO-driven implements: Set shift lever (4) at the implement to “I” – shifting takes place at the base machine. For dismounting, proceed in reverse order. agria Hydrostatic Tool Carrier 5900 Bison...
Replace the fuse if it is defective. To do this, open the fuse holder (version petrol engine: take out the battery beforehand) - ensure to provide another spare fuse in time. agria Hydrostatic Tool Carrier 5900 Bison...
Check transmission oil level (see page 53). Note: For reasons of transport, the engine is not filled completey with engine oil! Before you operate the engine the first time, fill in engine oil (see page 46)! agria Hydrostatic Tool Carrier 5900 Bison...
Page 34
Check transmission oil level (see page 53). Note: For reasons of transport, the engine is not filled completey with engine oil! Before you operate the engine the first time, fill in engine oil (see page 48)! agria Hydrostatic Tool Carrier 5900 Bison...
Page 35
Do not touch the hot engine - danger of burns! Do not touch or remove the ignition line and spark plug connector while the engine is running. agria Hydrostatic Tool Carrier 5900 Bison...
Page 36
Do not let snap. Trailing is not permitted! Once the engine has started, set speed control lever to min. and let engine warm up for some time. Slowly push choke back into operating position, if necessary. agria Hydrostatic Tool Carrier 5900 Bison...
Page 37
This ensures carburetor to be empty and no resin residue to deposit. agria Hydrostatic Tool Carrier 5900 Bison...
(re-start lock). Trailing is not permitted! Once the engine has started, set speed control lever to min. and let engine warm up for some time. Slowly push choke back into operating position, if necessary. agria Hydrostatic Tool Carrier 5900 Bison...
This ensures carburetor to be empty and no resin residue to deposit. Turn key back to position “0” and disconnect it. agria Hydrostatic Tool Carrier 5900 Bison...
Once the engine has started, slowly push speed control lever to centre position and let engine warm up for some time. In case the engine does not start, repeat the starting procedure. agria Hydrostatic Tool Carrier 5900 Bison...
This en-sures continued and reliable operation. 1 Min. Set speed control lever (B/9) to “STOP”. For shutting off the engine never activate decompression,as this might damage the valves. Close the fuel tap (D/3). agria Hydrostatic Tool Carrier 5900 Bison...
Page 42
If the engine does not start and re-start is necessary, turn key back to position “0” to repeat start (re-start lock). Slowly move speed control lever to centre po- sition (half throttle) and let engine warm up for some time. agria Hydrostatic Tool Carrier 5900 Bison...
Page 43
For shutting off the engine never activate decompression, as this might damage the valves. Turn key back to position “0” – warning signal goes out. Close the fuel tap (D/3). Secure tool carrier against unauthorized use – remove ignition key. agria Hydrostatic Tool Carrier 5900 Bison...
Proceed vice versa for direction change from reverse to forward. Never leave tool carrier unattended with the engine running. Danger zone Danger Zone Keep out of the machine’s danger zone during starts and operation. agria Hydrostatic Tool Carrier 5900 Bison...
Re-start engine. If cleaning becomes necessary during operation, the engi- ne must be shut off and the spark plug connector disconnected or the igni- tion key removed for safety reasons. agria Hydrostatic Tool Carrier 5900 Bison...
Ensure the waste oil is disposed of properly! Check sealing washer for good condition and exchange, if necessary. Tighten oil drain plug! Fill in fresh engine oil. - For engine oil quality refer to “Specifications”. agria Hydrostatic Tool Carrier 5900 Bison...
Otherwise danger of fire results. Check each time before you put the tool carrier into operation. All other maintenance on the engine Briggs & Stratton Engine agria Hydrostatic Tool Carrier 5900 Bison...
Check sealing washer for good condition and exchange, if necessary. Tighten oil drain plug! Refer to Specifications for oil quantity and quality. Use a funnel or a similar device to fill the oil reservoir. agria Hydrostatic Tool Carrier 5900 Bison...
Reposition air filter cap and fasten with wing nut. Replace paper filter element af- ter every 400 operating hours or at least once a year. Replace immediately damaged filter elements. agria Hydrostatic Tool Carrier 5900 Bison...
Page 50
Although the engine is equipped with an automatic fuel hoses immediately bleeding system, proceed as follows: Fill diesel fuel into fuel tank. Crank engine several times with recoil starter or electric starter and start engine. Let engine run for approx.1 minute. agria Hydrostatic Tool Carrier 5900 Bison...
After every 400 operating hours, clean and check injection jet. - Service Idling Speed Always ensure that idling engine speed is adjusted correctly. At low speeds, the engine is supposed to run smoothly, with speed control lever at stop in neutral. - Service agria Hydrostatic Tool Carrier 5900 Bison...
Careful when 50 h handling battery acid – etching! Only use speci- fied fuses. If fuses are too strong, the electric sys- > tem will be destroyed – danger of fire! agria Hydrostatic Tool Carrier 5900 Bison...
(A/9) with 140 Nm and counter it again. - Service Loading Belt Check loading belt for damage before each use and each time you maintain the machine, replace it not later than 10 years. agria Hydrostatic Tool Carrier 5900 Bison...
Page 55
- Service Wheel Motors Always after 200 operating hours, check for straight driving with the steering handle in neu- tral position. - Service agria Hydrostatic Tool Carrier 5900 Bison...
If necessa- ry, correct engine speed cable or Check electric lines and connections STOP-Bowden ca- ble on Bowden cable set screws. and exchange. - Service - Service agria Hydrostatic Tool Carrier 5900 Bison...
X or idle is present in position 0. Screw set pin in to reduce play, screw out to in- crease play. Place cable end adjusting pin back into bracket and check, fit retaining spring (2). agria Hydrostatic Tool Carrier 5900 Bison...
Clean engine only with a cloth. Avoid spraying with air- compressed water jets, as water might leak into ignition and fuel system causing malfunctions. agria Hydrostatic Tool Carrier 5900 Bison...
Clutch Petrol Engine Drain fuel completely or fill fuel tank Always park two- Petrol and add fuel stabilizer (agria No. 799 wheel tractor with 09). - Observe enclosed instructions. clutch lever pulled Let engine run for approx. 1 minute.
(Option set 786 44) Connection at the engine 1 Regulator 12 V 2 Condenser Al-ELKO 2200µF-10+30% 40 V br = brown 3 Socket 12 V DIN 9680-A ro = red 4 Connection engine ge = yellow agria Hydrostatic Tool Carrier 5900 Bison...
Page 61
9 Socket 12 V DIN 9680-A 10 Start switch (2x ge) Regulator 11 Battery 12 E-Starter 12 V Idle circuit (Oil Gard) 13 Start relay 14 Beeper 15 Electric rectifier 16 Relay change-over-contact 12 VDC 30 A agria Hydrostatic Tool Carrier 5900 Bison...
Page 62
= red 9 Socket 12 V DIN 9680-A sw = black 10 Start switch sw/ro = black-red 11 Battery ws = white 12 E-Starter 12 V 0,8 kW 14 Beeper 17 Operating Hours Counter agria Hydrostatic Tool Carrier 5900 Bison...
6. Troubleshooting Observe safety instructions! Have all serious malfunctions on the machine or engine repaired by your agria workshop. They have the proper tools. Improper repairs can only add to the damage. Problem Possible cause Remedy Page Petrol Engine: Engine...
Page 64
Move start switch to ”I” signal - Beeper is defective Replace beeper sounds - Fuse is defective Replace fuse when engine - Harness is damaged Check harness stops - Regulator is defective Check regulator agria Hydrostatic Tool Carrier 5900 Bison...
Page 65
- Idle shift is operated Activate hydraulic drive Excessive - Loosened attachment bolts Tighten attachment bolts vibration = For this purpose contact your agria workshop! BM = see separate engie operating instructions 6 6 6 agria Hydrostatic Tool Carrier 5900 Bison...
200 h, J, B 100 h, (5 h) (25 h) 50 h Diesel 25 h 600 h (50 h) 200 h (50 h) 200 h (50 h) yearly after each cleaning with a high-pressure cleaner agria Hydrostatic Tool Carrier 5900 Bison...
A = Each time before you take up operation workshop B = After each cleaning, especially with a high- F = Maintenance should be carried out by your pressure cleaner agria workshop J = min. yearly * = after 2 years agria Hydrostatic Tool Carrier 5900 Bison...
Assembly: A Clip roller guard support (1) to draw spindle of wheel motors B Push roller guard (2) over wheel motors - Note notch for brake lever. Fasten with screws (4) and washers (3) agria Hydrostatic Tool Carrier 5900 Bison...