Dip Switch Programming; Mode Descriptions - Viking C-1000B Technical Practice

E. Dip Switch Programming
Switch Position Description
1 OFF Doorstrike Activation = 0.5 seconds (factory setting)
1 ON Doorstrike Activation = 10 seconds
2 OFF Normal Mode (factory setting)
2 ON Security Code Bypass Mode
3 OFF Line Concentrator Mode
3 ON Normal Operation (factory setting)
F. Mode Descriptions
Entering these codes while in programming will switch the C-1000B into the corresponding mode.
Disable Special Modes (✱0): This command disables (clears) all the special modes listed below. Enter this command before pro-
gramming the rest of the selections to be sure no unwanted modes are set.
Doorbell Mode (✱1): In this mode, the ring signal from either doorbox is prevented from going through to the "LINE OUT TO
PHONES" terminals. This is useful when a conventional door bell is connected to the auxiliary contacts. Now when someone acti-
vates a doorbox, the doorbell will chime rather than the phone ringing (see Programming section B).
Custom Ring Mode (✱2): With this mode selected, the ring signal from the device ports are interrupted in a double burst pattern,
making it easier to determine if the incoming call is from a doorbox or the C.O. line. Note: Some telephones and phone systems
are not compatible with this feature.
Multiple Relay Activation Mode (✱3): If selected, after a door strike command is entered, the phone is switched back to the door-
box port so additional doorstrike (relay activation) commands can be entered.
gate with the first command then unlocking your front doorstrike with a second command. To return to the call on hold, enter "#".
Paging Mode (✱4): In this mode a paging system that provides talk battery (Viking PA-2A or CPA-7B) can be connected to one of
the doorbox ports. When the person on the phone wants to make a page, they can enter "#" and a "1" or "2" depending on which
port the paging amplifier is on. After the announcement is made another "#" will return them to the phone conversation.
Analog PABX/KSU Station Mode (✱5): This mode is ideal when installing the C-1000B on a phone system that does not have a
spare trunk port but does have an unused analog station port. This mode allows any standard (POTS) telephone such as the E-10,
E-20A, E-30 or K-1700-3 to be used in place of Doorbox 1. Only one door phone can be used in this mode. When the door phone
goes off-hook, a hot-line dialer or ringdown station will call the desired phone system extension. The phone on that extension can
then communicate with the door phone and activate doorstrikes as needed. Note: Only a single door phone may be used. Multiple
relay activation mode cannot be used with Viking door phone models E-30 or any 1600A Series phone.
Inhibit Latching Commands Mode (✱6): In some installations it is critical that the door strike or door actuator not be turned on for
long periods of time. To prevent this from happening, enter ✱6 when in programming. In this mode, the toggle command (✱#) and
the continuous activation command (✱1) are ignored.
O p e r a t i o n
O p e r a t i o n
A. Doorbox Controller
1. Communicating with the Doorbox
a. Visitor Initiated Call
A visitor pressing the "Call" button will cause the phones connected to the "LINE OUT TO PHONES" terminals to ring. Simply
answer your phone to converse with the visitor. After answering the call, a single or double beep will be heard in the phone,
indicating which doorbox has called - a single beep for doorbox 1 and a double beep for doorbox 2.
b. Monitoring Doorboxes
A doorbox may be monitored from any phone connected to the C-1000B by Touch Tone dialing a "#" followed by a Touch
Tone "1" or "2" to monitor doorbox 1 or doorbox 2 respectively. This feature is not available for pulse dialing phones. Note:
Do not attempt doorbox monitoring while a call is in progress, the call will be disconnected. Note: When monitoring, the
auxiliary contact will only work on the Continuous Mode (11).
2. Placing C.O. Line Calls on Hold
If a C.O. line call is in progress and a doorbox is activated, a single or double "call waiting" tone will be heard indicating doorbox
1 or doorbox 2 is calling. To place the in-progress call on hold and answer the calling doorbox, simply dial a Touch Tone "#",
pulse dial a "2" or hook flash twice.
3. Activating a Doorstrike, Magnetic Lock or Gate Controller
To activate a relay contact, you must be communicating with a doorbox. Simply Touch Tone dial "✱✱", pulse dial a "3" or hook
flash three times. Two confirmation tones will be heard and the relay will be activated for the programmed doorstrike activation
time. The phone will then be returned to the C.O. line. If a call was in progress, the original caller will be taken off hold to con-
tinue the conversation. To return to the original call without activating a relay, Touch Tone dial "#", pulse dial a "2" or hook flash
twice.
VIKING
MODEL C-1000B
©
VIKING
ELECTRONICS
HUDSON, WI 54016
DOOR ENTRY / CCTV VIDEO
/ PAGING CONTROLLER
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
COM N.O. N.C. - - - - AUX.
CONTACT
OUTPUT
ON
SIG GND SIG GND SIG GND
VIDEO 1 IN VIDEO 2 IN VIDEO OUT
1 2 3
C C C
TALK BATTERY
LED1 LED2 LED3
OFF ON
EARTH C.O. LINE OUT TO KEYLESS DOOR DOORBOX DOOR N.O. COM N.C. N.O. COM N.C.
GND INPUT PHONES C.C. INPUT BOX 1 13VAC PWR BOX 2 DOOR STRIKE 1 DOOR STRIKE 2
This is useful when letting someone through your
DIP Switches shown
in the factory default
positions
ON
ON
OFF
1 2 3
(7)