Table of Contents
Advertisement
Quick Links
Designed, Manufactured and Supported in the USA
VIKING
C O M M U N I C A T I O N & S E C U R I T Y S O L U T I O N S
Add Entry Phones and Door Strike Control to an
Existing Line Or Securely Operate Multiple Door Strikes
The C-2000B offers two operational modes for flexibility
in operation.
In the Single Line Ring Through Mode, the C-2000B
allows single line phones to share a phone line with 1 to
4 entry phones. Tenants may converse with visitors and
activate a contact closure to control gates or strikes. The
C-2000B provides entry phone "Caller ID" and "Call
Waiting Caller ID" and a "Call Waiting" tone when the
phone line is in use. Tenants can enter at each location
by entering a keyless entry code.
In the Analog Station Dial Through Mode, the C-2000B
allows 1 to 4 entry phones to share one analog PABX
extension or telephone line and place outgoing calls.
When a remote party answers, they can converse with
visitors and activate a contact closure to control gates or
strikes. Monitoring entry phones, forcing door strike relays
to operate or remote programming of the C-2000B can be
accomplished by calling the analog PABX extension or
telephone line connected. Authorized personnel can enter
at each location by entering a keyless entry code.
Features
• Allows 1-4 entry phones to share a single telephone line
with a residential or business telephone system
• Compatible with the following Viking entry phones:
- E-10A, E-20B, E-30, E-35, E-40, E-50, E-60, E-65,
E-70, and E-75 Phones
- K-1500-7 Stainless Steel Panel Phone
- K-1700-3 and K-1705-3 Phone with Keypad
- K-1900-8 Stainless Steel Panel Phone with Keypad
- Or use with any analog touch tone phone
• Provides entry phone activated chimes and whole house
paging when used with an SLP-1 or SLP-4
• Up to 6 different keyless entry codes / "one time use"
keyless entry codes per entrance
• Up to 6 master keyless entry codes for use at any entry
• Analog Station Dial Through Mode allows entry phones to
connect to an analog PABX station or telephone line
• Optional "Privacy Number" allows only selected visitors to
call from an entry phone
• Provides "Caller ID" and "Call Waiting Caller ID"
• Produces "Call Waiting" tones
• Programmable entry phone Caller ID messages
• Lighted doorbell switch input to activate entry phone call
• One set of normally open and normally closed contacts
available for each entry phone
• Programmable door strike activation code
• Programmable contact activation time
• Auxiliary input to activate timed auxiliary contacts
PRODUCT MANUAL
In either operational mode, the secure relay control of the
C-2000B prevents the entry phone from dialing the
activation code on the keypad of the entry phone or using
a hand held touch tone dialer. An auxiliary input is
available for connecting a lighted doorbell switch, a
common garage door opener/receiver or an auxiliary
keyless entry keypad.
Applications
• Add one to four entry phones to your standard home or
office phones to provide:
- Door communication
- Door entry
- Gate entry
- Keyless entry
• Provide commercial or residential security via two-way
handsfree communication at the door and gate
• Connects in series with a single phone line or to a
phone system's unused line input (loop start trunk input)
• High security building entry systems
• Door strikes and gates in conjunction with entry phones
or hot-line/panel phones
www.VikingElectronics.com
Information: (715) 386-8861
Specifications
Power: 120VAC / 13.8VAC 1.25A, UL listed adapter provided
Dimensions: 210mm x 159mm x 45mm (8.25" x 6.25" x 1.75")
Shipping weight: 1.5kg (3.2 lbs.)
Environmental: 0°C to 32°C (32°F to 90°F) with 5% to 95%
non-condensing humidity
Relay Contacts: 5A @ 30VDC/250VAC
Ring Output: 8 REN, capable of ringing (16) 0.5 REN phones
Talk Battery: 40V DC
REN: 0.1A
Connections: (32) cage clamp screw terminals
C-2000B
Advanced Door/Gate
Entry Phone Controller
September 20, 2017
Advertisement
Table of Contents
Related Manuals for Viking C-2000B
Summary of Contents for Viking C-2000B
- Page 1 Monitoring entry phones, forcing door strike relays activation code on the keypad of the entry phone or using to operate or remote programming of the C-2000B can be a hand held touch tone dialer. An auxiliary input is accomplished by calling the analog PABX extension or available for connecting a lighted doorbell switch, a telephone line connected.
-
Page 2: Features Overview
IMPORTANT: Please read the following sections to determine which C-2000B mode works best for your application. The C-2000B has two operational modes built in, called the “Single Line Ring Through Mode” and “Analog Station Dial Through Mode”. The “Single Line Ring Through Mode” is the residential “line sharing”... - Page 3 If one of the entry phones is using the line and a second entry phone goes off hook, it will receive a busy signal (generated by the C-2000B) until the line becomes available.
-
Page 4: Installation And Applications
A. One to Four Entry Phones Sharing a Single Phone Line with House Phones Note: The C-2000B is not recommended to be installed in combination with the TR-1 Toll Restrictor. Contact your local C.O. for toll restriction requirements. - Page 5 Entry Phones and Door Strikes from a Single Phone Line with the Viking C-2000B and SLP-4 The SLP-4 can be used with the Viking C-2000B entry phone controller. The phone line first runs through the SLP-4, then runs through the C-2000B before continuing on to the house phones. The C-2000B ’s normally open Aux Contact Output connections, when wired to the SLP-4’s Trig1 input, will play the SLP-4’s DIP Switch selected...
- Page 6 D. Using a C-2000B without a C.O. Line The C-2000B can also be used without a C.O. line. This is ideal for connecting the C-2000B to an unused trunk/line input of your phone system or connecting to phones used only for doorbox communication.
-
Page 7: Accessing Programming
Step 5. When finished programming, hang up and move DIP switch 2 to the OFF position. 3. Accessing the Programming Mode Remotely Call into the C-2000B from a touch tone phone. Note: Call in from another line to Step 1. - Page 8 *** Note: The entry phone 1 position can not be programmed in the No Entry Phone Mode while the C-2000B is in the Doorbell Mode (DIP switch 1 ON, see page 9), as the Doorbell Mode relies on entry phone 1. The C-2000B will provide 3 error beeps if you attempt to...
- Page 9 Normal Operation Mode (factory setting) Security Code Bypass Mode Entry Phone automatic disconnect (CPC) disabled Note: Viking handsfree entry phones require CPC for 1 2 3 4 5 6 7 8 9 10 11 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32...
- Page 10 Notes: 1. Entry phone 1 ringing the house phones can be disabled in this doorbell mode, if it is desirable to have the doorbell chime but not the house phones ring. This option can only be used if there is only one entry phone on the C-2000B.
- Page 11 If a master keyless code is entered with Global Keyless Entry enabled, the C-2000B will activate the relay for the entry phone the user is connected to, just as it would if Global Keyless Entry was not enabled.
-
Page 12: Outside Line Access
“0” in place of the “1” in the memory location for that entry phone. Note: The entry phone 1 position cannot be programmed in the No Entry Phone Mode while the C-2000B is in the Doorbell Mode (DIP switch 1 ON), as the Doorbell Mode relies on entry phone 1 being connected in order to operate correctly. -
Page 13: Operation
A. Visitors When a visitor presses the call button (comes off-hook) on the entry phone, the C-2000B will begin ringing the house phones and entry phone “Caller ID” information is sent. If a house phone is on a C.O. call, call waiting tones and entry phone “Call Waiting Caller ID”... -
Page 14: Operation Commands
C-2000B to not accept the command. This problem can be corrected by enabling the “# Conflict Mode”... - Page 15 30A, etc.). An external dialer or ringdown feature must be used. In the doorbell mode, a K-1900-30 dialer can not be installed on the entry phone side of the C-2000B. It must be installed on the analog extension or telephone...
- Page 16 Door Strikes with the Viking C-2000B and SLP-4 The SLP-4 can be used with the Viking C-2000B entry phone controller. The C-2000B ’s normally open Aux Contact Output connections, when wired to the SLP-4’s Trig1 input, will play the SLP-4’s DIP Switch selected recorded door chime whenever Entry Phone 1, 2, 3 or 4 calls in.
- Page 17 1. Accessing the Programming Mode with a security Code Step 1. Call the station/extension the C-2000B is connected to. The C-2000B will answer the call after the programmed ring delay (factory set to 1) and output a Step 2. single beep.
-
Page 18: Dip Switch Programming
Erase all keyless codes * Note: The entry phone 1 position can not be programmed in the No Entry Phone Mode while the C-2000B is in the Doorbell Mode (DIP switch 1 ON, see page 18), as the Doorbell Mode relies on entry phone 1. The C-2000B will provide 3 error beeps if you attempt to program “1#81”... - Page 19 (causing the doorbell to chime again). 3. A K-1900-5 dialer can not be installed on the entry phone side of the C-2000B. It must be installed on the analog extension or telephone line before the C-2000B.
- Page 20 L. Analog Station Ring Delay (#63) If the C-2000B is called, it will answer on the first ring and give a single beep. This factory-set ring delay can be changed, to a ring delay from 1 to 99. The Analog Station Ring Delay must be 2 digits and is stored in location #63.
- Page 21 M. Analog Station Inbound Call Timer (#64) After the C-2000B answers an incoming call, it is possible to enter #1, #2, #3, or #4 to monitor one of the entry phones. When monitoring an entry phone, an inbound call timer starts. The default value for this timer is 1 minute, but it can be changed in programming to 1-99 minutes.
- Page 22 “Q” or “#” touch tone is dialed. “#” is a hang up command to the C-2000B, so it disconnects the entry phone from the line and hangs up the extension or telephone line when a “#”...
- Page 23 If a privacy number has been programmed, an off-hook entry phone is given 4 seconds of simulated dial tone to allow the visitor to enter the privacy number. If the visitor enters the correct privacy number, the C-2000B will connect the entry phone to the analog PABX extension or telephone line. If they enter an incorrect number, they will be disconnected.
-
Page 24: Warranty
This number is valid for fourteen (14) calendar days from the date of issue. 3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your distributor will then replace the Viking product using the same R.A. number.