Sunell SN-TPC6406KT-F User Manual
  1. Manuals
  2. Brands
  3. Sunell Manuals
  4. Security Camera
  5. SN-TPC6406KT-F
  6. User manual

Sunell SN-TPC6406KT-F User Manual

Thermal imaging integrated network camera
Hide thumbs Also See for SN-TPC6406KT-F:
Table of Contents

Advertisement

Quick Links

Download this manual
Thermal Imaging Integrated Network Camera
User Manual
Issue
V1.0
Date
2022-09-07

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SN-TPC6406KT-F and is the answer not in the manual?

Questions and answers

Related Manuals for Sunell SN-TPC6406KT-F

Summary of Contents for Sunell SN-TPC6406KT-F

  • Page 1 Thermal Imaging Integrated Network Camera User Manual Issue V1.0 Date 2022-09-07...

  • Page 3: Precautions

    Thermal Imaging Integrated Network Camera User Manual Precautions Precautions Precautions Fully understand this document before using this device, and strictly observe the rules in this document when using this device. If you install this device in public places, put a sign "You have entered the area of electronic surveillance" in an eye-catching place. Failure to correctly use electrical products may cause fire and severe injuries.
  • Page 4 Thermal Imaging Integrated Network Camera Precautions User Manual Strictly conform to local electrical safety standards and use power adapters which ⚫ are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged. Use accessories delivered with this device. The voltage must meet input voltage ⚫...
  • Page 5 Thermal Imaging Integrated Network Camera User Manual Precautions Clean the device body with a soft and dry cloth. In case that the dirt is hard to ⚫ remove, use a dry cloth dipped in a small amount of mild detergent and gently wipe the device, and then dry it again.

  • Page 6: Table Of Contents

    Thermal Imaging Integrated Network Camera Contents User Manual Contents Precautions ............................. i Contents ............................iv 1 Product Overview ........................1 Thermal Imaging Principles and Advantages ..............1 Device Structure ......................1 Out Wire Connection ....................... 3 1.3.1 The Multi-connector Cables.................. 3 1.3.2 Integrated Cable Management Bracket ..............
  • Page 7 Thermal Imaging Integrated Network Camera User Manual Contents Mode ..........................52 Images ........................... 53 Scene ..........................54 Set Pseudocolor ......................56 FFC Control ........................57 Noise Reduction ......................59 5 AI Multiobject .......................... 61 Parameters of AI Multiobject ..................61 6 Intelligent Analysis ........................

  • Page 9: Product Overview

    Thermal Imaging Integrated Network Camera User Manual Product Overview Product Overview Thermal Imaging Principles and Advantages For any object, as long as its temperature is above the absolute zero (-273.15°C), although the object does not give out light, it can radiate infrared. The infrared is also known as thermal radiation.
  • Page 10 Thermal Imaging Integrated Network Camera Product Overview User Manual Appearance and Interfaces of the Camera Interfaces of Device Physical Interface Connection Reset button The configuration resumes to the factory settings (RESET) after you press the reset button for 5s. The default value is 192.168.0.121.

  • Page 11: Out Wire Connection

    Thermal Imaging Integrated Network Camera User Manual Product Overview Out Wire Connection There are two ways to connect the thermal imaging integrated network camera, the multi-connector cables and the integrated cable management bracket. Users can choose the corresponding method and installation method according to their bracket. 1.3.1 The Multi-connector Cables Figure 1-2 the multi-connector cable of the thermal imaging integrated network camera.
  • Page 12 Thermal Imaging Integrated Network Camera Product Overview User Manual Core of Cable Functions Connection Network interface Connect to the standard Ethernet cable. Orange Alarm out com 2 Connect to the alarm devices. Yellow Alarm out 2 Grey Alarm in com 2 Purple Alarm in 2 Brown...

  • Page 13: Integrated Cable Management Bracket

    Thermal Imaging Integrated Network Camera User Manual Product Overview 1.3.2 Integrated Cable Management Bracket Integrated Cable Management Bracket Port Integrated Cable Management Bracket Port Port Name Description Remark COM OUT 1 Alarm out com 1 ALARM OUT1 Alarm out 1 COM IN 1 Alarm in 1 com ALARM IN1...

  • Page 14: Packing List

    Thermal Imaging Integrated Network Camera Product Overview User Manual CVBS GND Analog video output ground port。 COM OUT2 Alarm out com 2 ALARM OUT2 Alarm out 2 COM IN2 Alarm OUT com 2 ALARM IN2 Alarm in 2 RS485+ RS485+ Applied for connecting to RS485-...

  • Page 15: Device Dimensions

    Thermal Imaging Integrated Network Camera User Manual Product Overview bracket Cable gland Configured for B bracket Junction box and accessories Configured for B bracket Device Dimensions The different brackets of device are having different dimensions, please refer to actual product. Issue V1.0（2022-09-07）...
  • Page 16 Thermal Imaging Integrated Network Camera Product Overview User Manual The A Bracket With Junction Box Dimensions (unit: mm) Longer Sun-shaded The A Bracket With Junction Box Dimensions (unit: mm) Shorter Sun-shaded Issue V1.0（2022-09-07）...
  • Page 17 Thermal Imaging Integrated Network Camera User Manual Product Overview Issue V1.0（2022-09-07）...
  • Page 18 Thermal Imaging Integrated Network Camera Product Overview User Manual The B Bracket Dimensions (unit: mm) Longer Sun-shaded The B Bracket With Junction Box Dimensions (unit: mm) Shorter Sun-shaded Issue V1.0（2022-09-07）...
  • Page 19 Thermal Imaging Integrated Network Camera User Manual Product Overview Issue V1.0（2022-09-07）...

  • Page 20: Installation

    Thermal Imaging Integrated Network Camera Product Overview User Manual Installation 1.6.1 Preparations Tools needed (Not included) and supplied parts are shown in Table 1-5. Installation Tools Tools Appearance Phillips screwdriver (Not included) Claw hammer (Not included) Hammer drill (Not included) Spirit level (Not included) T15 ring spanner (Included) Self-tapping screw (Included)

  • Page 21: Installing Bracket Without Junction Box

    Thermal Imaging Integrated Network Camera User Manual Product Overview NOTE  The wall where the support is mounted must be able to withstand at least three times of the total weight of the support and the camera.  The different brackets have different installation methods, please choose the corresponding method according to the purchased product.
  • Page 22 Thermal Imaging Integrated Network Camera Product Overview User Manual Fixing Camera Connect the multi connector cable. Loosen the screw 1 and screw 2, adjust the surveillance angle, as shown in Figure 1-10 After adjusting angle, fix screw 2 and screw 1 in turn to finish installation, as shown in Figure 1-10.

  • Page 23: Installing Bracket With Junction Box

    Thermal Imaging Integrated Network Camera User Manual Product Overview Adjust the Surveillance Angle ----End 1.6.2.2 Installing Bracket With Junction Box Take out the installation location label from the package, stick it on the ceiling or the wall. According to the location hole positions shown in the installation location label, punch four location holes on the ceiling or the wall.
  • Page 24 Thermal Imaging Integrated Network Camera Product Overview User Manual Fixing the Junction Box Wiring of junction box. Align the holes in bracket with the box and fix the camera to the box with self-tapping screws, as shown in Figure 1-12. Fix the Camera to the Junction Box Issue V1.0（2022-09-07）...
  • Page 25 Thermal Imaging Integrated Network Camera User Manual Product Overview Connect the multi connector cable. Loosen screw 1 and screw 2, adjust the surveillance angle, as shown in Figure 1-13. Adjust the Surveillance Angle After adjusting angle, fix screw 2 and screw 1 in turn to finish installation. ...

  • Page 26: Quick Configuration

    Thermal Imaging Integrated Network Camera Quick Configuration User Manual Quick Configuration Login and Logout To access the web interface through Microsoft Edge browser (IE Mode); Otherwise, some functions may be unavailable. Login system Open the Microsoft Edge, enter the IP address of IP camera (default value: 192.168.0.121) in the address box, and press Enter.

  • Page 27: Browsing Video

    Thermal Imaging Integrated Network Camera User Manual Quick Configuration Internet Explorer Compatibility  The default name and password are both admin. Modify the password when you login the system for first time to ensure system security.  After modifying password, you need to wait at least three minutes then power off to make sure modifying successfully.
  • Page 28 Thermal Imaging Integrated Network Camera Quick Configuration User Manual Preparation In order to view live video normally, the following steps are performed for the first access. Open the Microsoft Edge. Choose Control panel > Internet options > Security > Trusted sites > Sites. In the display dialog box, click Add, as shown in Figure 2-3.

  • Page 29: Install Plugins

    Thermal Imaging Integrated Network Camera User Manual Quick Configuration Configuring ActiveX Control and Plug-ins Download and install the player control as prompted. The login page is displayed when the control is loaded. 2.2.1 Install Plugins You will be prompted with a message “Download and install the new plugin” will show as in Figure 2-5, when you log in to the web management system for the first time.

  • Page 30: Main Page Layout

    Thermal Imaging Integrated Network Camera Quick Configuration User Manual Main Page Layout On the main page, you can view Live Video, Playback, People Counting and Configuration. Parameter setting, Video control, Web login and logout can be performed by PC. The main page layout shown in Figure 2-6. For more details, please refer to Table 2-1.
  • Page 31 Thermal Imaging Integrated Network Camera User Manual Quick Configuration Function Description Sign Out You can click to return to the login page. Stream There are three streams. Choose one type from drop-down list. Pause/Start Click to pause or play live video. Live/Smooth Switch image quality.

  • Page 32: People Counting

    Thermal Imaging Integrated Network Camera Quick Configuration User Manual The Icon : The lowest temperature of the full screen. : The highest temperature of the full screen. : The lowest temperature of the area. : The highest temperature of the area. People Counting At people counting interface, you can view the people counting throughout setting query condition (choose the detail time at date’s pop up window).

  • Page 33: Changing The Password

    Thermal Imaging Integrated Network Camera User Manual Quick Configuration People Counting Interface Users can choose the querying mode (year, month, day). The data can be viewed directly, or downloaded them. The statistic can be showed by line chart, histogram, or list. ----End Changing the Password Description...

  • Page 34: Setting Local Network Parameters

    Thermal Imaging Integrated Network Camera Quick Configuration User Manual Change Password Dialog Box The change password page will be displayed if you don’t change the default password when you log in the system for the first time. Enter the old password, new password, and confirm password. Click OK.
  • Page 35 Thermal Imaging Integrated Network Camera User Manual Quick Configuration Procedure Choose Configuration > Device >Local Network. The Local Network page is displayed, as shown in Figure 2-10. Device Information Set the parameters according to Table 2-2. Local Network Parameters Parameter Description Setting IP Protocol...
  • Page 36 Thermal Imaging Integrated Network Camera Quick Configuration User Manual Parameter Description Setting DHCP IP IP address that the DHCP server assigned to the device. IP Address Device IP address that can be [Setting method] set as required. Enter a value manually. [Default value] 192.168.0.121 Subnet Mask...
  • Page 37 Thermal Imaging Integrated Network Camera User Manual Quick Configuration  If you set only the Subnet Mask, Default Gateway, Preferred DNS Server, and Alternate DNS Server parameters, you do not need to log in to the system again.  You can click Refresh to set the parameters again if required. ----End Issue V1.0（2022-09-07）...

  • Page 38: Thermal Settings

    Thermal Imaging Integrated Network Camera Thermal Settings User Manual Thermal Settings Temperature Parameters Temperature parameters include: temperature unit, ambient temperature, cavity temperature, correctional coefficient area temperature display mode, and so on. The temperature and length unit are used for all parameters which occur at the software. The Open Temperature Measure should be enable in advance, if not there are no temperature showing on screen, and the alarms settings are invalid.
  • Page 39 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Temperature Parameters Interface Set the parameters according to Table 3-1. Temperature Parameters Parameter Description Setting Temperature Enable to open temperature [Setting method] Measurements measure. Enable Temperature Units Celsius and Fahrenheit [Setting method] temperature units are available.
  • Page 40 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Parameter Description Setting Length Units Meters and Feet [Setting method] Select a value from the drop-down list box. [Default value] Meters Cavity Temperature The cavity temperature of camera. Correction Correction coefficient is refer to [Setting method] Coefficient the deviation of measured...
  • Page 41 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Parameter Description Setting Font Size Custom font size. There are [Setting method] three sizes can be chosen. Select a value from the drop-down list box. Area Temperature There are three types of area [Setting method] Type temperature.
  • Page 42 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Parameter Description Setting Temper Duration(5- Prevent over heat’ mode is auto, [Setting method] 60s) the control cover will block for Enter a value manually duration time automatically if ranges from 5 to 60. over heat.

  • Page 43: Ambient Temperature

    Thermal Imaging Integrated Network Camera Thermal Settings User Manual ----End Ambient Temperature Set the ambient temperature of camera, click “Apply” to save the setting, click “Refresh” the cavity temperature will be refresh based on ambient temperature. Ambient Temperature parameter of Ambient Temperature Parameter Description Setting...
  • Page 44 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Temperature Alarm Configuration Set the parameters according to Table 3-4 Temperature Alarm Configuration Parameter Description Setting Channel [Setting method] Select a value from the drop-down list box. [Default value] Issue V1.0（2022-09-07）...
  • Page 45 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Parameter Description Setting Measure Mode Set at temperature parameter interface. Enable Tick to enable the area alarm [Setting method] Tick Name Area name of temperature area. [Setting method] Enter a value manually. Type Type of temperature area.
  • Page 46 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Parameter Description Setting Choose temperature rise alarm, Duration (1-10s) set the duration, the temperature rise the value and it is kept for duration setting, the alarm is triggered successfully. The emission rate is the Emission Rate [Setting method] capability of an object to emit...
  • Page 47 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Parameter Description Setting Group ID The ID can be chosen into one [Setting method] of six groups, or no group. The Select a value from the group will be alarm following drop-down list box.

  • Page 48: Privacy Zone Masking

    Thermal Imaging Integrated Network Camera Thermal Settings User Manual Temperature Area Setting Interface Click Apply, the message “Apply success” pops up, the temperature area is set successfully. Delete a temperature area: Select an area ID. Click the temperature area and right-click. Click Apply, the message “Apply success”...

  • Page 49: Schedule Linkage

    Thermal Imaging Integrated Network Camera Thermal Settings User Manual Privacy Zone Masking Enable the Privacy Zone Masking. Enable Privacy Zone Masking Display, then the setting masking areas will show on live video. Left-click to select polygon area, right-click to save. Click Apply to save the settings.
  • Page 50 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Schedule Linkage Tick the output channel. Enable “Alarm Record”, “SMTP”,”FTP Upload” , “Audible Alarm” button. Set schedule linkage. Method 1：Left click to select any time point within 0:00-24:00 from Monday to Sunday as shown in Figure 3-7.
  • Page 51 Thermal Imaging Integrated Network Camera Thermal Settings User Manual  Alarm output: Users should connect the external alarm device (such as siren) to alarm output cables. The parameter can be set at “ Configuration > Alarm > Alarm Output” interface, as shown in Figure 3-8.
  • Page 52 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Parameter Description Setting Alarm Output When the device receives I/O alarm [Setting method] Mode signals, the device sends the alarm Select a value from the information to an external alarm device drop-down list box.
  • Page 53 Thermal Imaging Integrated Network Camera Thermal Settings User Manual  Alarm Record: Users insert the SD card in camera. The recording time is set at “ Configuration > Device Record > Record Policy” interface. SMTP: At “ Configuration > Network > SMTP” interface, users should set the parameters of ...
  • Page 54 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Parameter Description Setting Recipient_E- (Mandatory) Email address of [Setting method] mail_Address recipient 1. Enter a value manually. Recipient_E- (Optional) Email address of mail_Address recipient 2. Recipient_E- (Optional) Email address of mail_Address recipient 3.
  • Page 55 Thermal Imaging Integrated Network Camera Thermal Settings User Manual FTP Upload: At “ Configuration > Network > FTP” interface, users should set the parameters  of FTP upload in advance, as shown in Figure 3-10. FTP Upload FTP Upload Parameters Parameter Description Setting...
  • Page 56 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Audible Alarm output: At “ Configuration > Alarm > Audible Alarm Output” interface, users  should set the parameters of Audible Alarm output in advance, as shown in Figure 3-11. Audible Alarm Output to upload the audible file (The type should User can set the audio file manually.

  • Page 57: Defect Pixel Correction

    Thermal Imaging Integrated Network Camera Thermal Settings User Manual Defect Pixel Correction Description The points that can’t move when the environment or scenario change is defect pixel. You can correct the these points manually. Procedure Choose Configuration > Thermal > Defect Pixel Correction. The Defect Pixel Correction page is displayed, as shown in Figure 3-13.
  • Page 58 Thermal Imaging Integrated Network Camera Thermal Settings User Manual Recover Defect Pixel Click Reset to return the previous settings. Click Apply. The message "Apply success" is displayed, the system saves the settings. ----End Issue V1.0（2022-09-07）...

  • Page 59: Image Settings

    Thermal Imaging Integrated Network Camera Image Settings User Manual Image Settings Image Settings Interface Operation Procedure On the Microsoft Edge IE mode interface or the client software interface, select and right-click the surveillance image to set, as shown in Figure 4-1. Right-click Configuration Parameters of Right-click parameters...

  • Page 60: Mode

    Thermal Imaging Integrated Network Camera Image Settings User Manual Thermal Channel Image Settings Choose Image settings. The dialog box is displayed, as shown in Figure 4-3. ----End Mode Figure 4-3 shows the Mode interface. Issue V1.0（2022-09-07）...

  • Page 61: Images

    Thermal Imaging Integrated Network Camera Image Settings User Manual Mode Interface Operation Procedure Click in the lower left corner of Image Settings, and choose Debug Mode. Choose switch mode form drop-down list. Set the Start Time. Set the End Time. Click Save, the message "Save succeed"...

  • Page 62: Scene

    Thermal Imaging Integrated Network Camera Image Settings User Manual Image Interface Click in the lower left corner of Image Settings, and choose Debug Mode. Drag the slider to adjust parameter of image. Brightness: It indicates the total brightness of an image. As the value increases, the image becomes brighter.
  • Page 63 Thermal Imaging Integrated Network Camera Image Settings User Manual Scene Interface Click in the lower left corner of Image Settings, and choose Scene Choose mirror mode from drop-list. Click Save, the message "Save succeed" is displayed, the system saves the settings. NOTE ...

  • Page 64: Set Pseudocolor

    Thermal Imaging Integrated Network Camera Image Settings User Manual Set Pseudocolor Figure 4-6 shows the Set Pseudocolor interface. Set Pseudocolor Interface Click in the lower left corner of Image Settings, and choose Set pseudocolor Choose Pseudo-colors modes from the drop-down list. Enable or disable the Legend of Temperature Value.

  • Page 65: Ffc Control

    Thermal Imaging Integrated Network Camera Image Settings User Manual The temperatures of the temperature fields detected by the thermal imaging camera are separately mapped to values ranging from 0 to 255 by the algorithm. In the black/white display mode, this range is converted to the gray scale tones. For example, 0 indicates completely black, and 255 indicates completely white.
  • Page 66 Thermal Imaging Integrated Network Camera Image Settings User Manual Table 4-2 lists the parameters on the FFC control interface. Parameters on the FFC Control Interface Parameter Description Setting The internal of the thermal imaging camera may comprise the mechanical action correction mechanism that can periodically improve the image quality.

  • Page 67: Noise Reduction

    Thermal Imaging Integrated Network Camera Image Settings User Manual Parameter Description Setting temperature of the camera sharply changes when the camera is powered on. The FFC is relatively frequent, which is normal. Manual: In the manual FFC mode, the camera does not automatically perform the FFC based on the temperature change or the specified period.
  • Page 68 Thermal Imaging Integrated Network Camera Image Settings User Manual Noise Reduction Interface Table 4-3 lists the Noise reduction parameters. Parameters on the Noise Reduction Interface Parameter Description Setting [How to set] Select from the drop-down list box. Decrease the image 2DNR noise.

  • Page 69: Ai Multiobject

    Thermal Imaging Integrated Network Camera AI Multiobject User Manual AI Multiobject Parameters of AI Multiobject To enable full body detection and vehicle detection, when the device detects the object, it will be triggered alarm. AI Multiobject Parameters of AI Multiobject Parameter Description How to set...
  • Page 70 Thermal Imaging Integrated Network Camera AI Multiobject User Manual Parameter Description How to set confidence, the better the detecting quality. If the target is static, the device will filter this Static Target target. For example, if a car stop for long time, Enable Filter the device will be filtered.

  • Page 71: Intelligent Analysis

    Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Intelligent Analysis Intrusion The Intrusion function refers to that an alarm is generated when the targets of specified types (such as person, car, and both person and car) enter the deployment area. Operation Procedure Select Intelligent Analysis >...
  • Page 72 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Intrusion Parameter Description Parameter Description Setting Enable Enable the button to enable the alarm. [How to set] Click Enable to enable. [Default value] Sensitivity The sensitivity of detecting the target, when [How to set] the value is high, the target can be detected Choose from the...
  • Page 73 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Parameter Description Setting FTP Upload Enable the button to enable File Transfer [How to set] Protocol. Click to enable FTP The parameters of FTP can be set at Upload. Configuration > Network Service > FTP [Default value] interface.

  • Page 74: Single Line Crossing

    Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Deployment Time Setting Interface ----End Single Line Crossing A Single Line Crossing is a line that is set at a concerned position within the monitored field of view and specifies the forbidden travel direction, an alarm is generated when the targets of specified types (such as person or car) cross this line.
  • Page 75 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Single Line Crossing Interface Set all parameters for the Single Line Crossing. Table 6-2 describes the specific parameters. Parameters of Single Line Crossing Parameter Description Setting Enable Enable the button to enable the alarm. [How to set] Click Enable to enable .
  • Page 76 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Parameter Description Setting Output If you check to set the Output Channel and the [How to set] Channel device is connected to an external alarm Click to select an ID. indicator, the alarm indicator signals when an alarm is triggered.

  • Page 77: Double Line Crossing

    Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual NOTE  A Single Line Crossing is not within any deployment area, therefore, when an alarm is generated, the trace always exists. Only when the target object moves out of the field of view, the trace disappears.
  • Page 78 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Double Line Crossing Interface Set all parameters for the Double Line Crossing. Table 6-3 describes the specific parameters. Parameters of Double Line Crossing Parameter Description Setting Enable Enable the button to enable the alarm. [How to set] Click to enable.
  • Page 79 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Parameter Description Setting Output If you check to set the Output Channel and the [How to set] Channel device is connected to an external alarm Click to select an indicator, the alarm indicator signals when an alarm is triggered.

  • Page 80: Multi-Loitering

    Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual endpoint of a virtual fence and move the mouse to modify the position and length of this virtual fence. You can right-click to delete the double line crossing. NOTE  The two virtual fences are in sequential order. An alarm is generated only when a target crosses virtual fence 1 and then virtual fence 2 within the set maximum passing time.
  • Page 81 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Multi-Loitering Setting Interface Set all parameters for multiple loitering. Table 6-4 describes the specific parameters. Parameters of Multiple Loitering Parameter Description Setting Enable Enable the button to enable the alarm. [How to set] Click Enable to enable.
  • Page 82 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Parameter Description Setting Limit Numbers When Limit Numbers is set to OFF, an alarm [How to set] is generated no matter how many people Click to enable loiter. When Limit Numbers is set to ON, if Limit Numbers.

  • Page 83: Wrong-Way

    Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Parameter Description Setting Video Stream Enable, the deployment frame will show on [How to set] Draw Line the live video. Click to enable Video Stream Draw Line. [Default value] Set a deployment area. Move the cursor to the drawing interface and click to generate a point, move the cursor to draw a line, and then click to generate another point.
  • Page 84 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Wrong-way Setting Interface Set all parameters for Wrong-way. Table 6-5 describes the specific parameters. Parameter of Wrong-way Parameter Description Setting Enable Enable the button to enable the alarm. [How to set] Click Enable to enable.
  • Page 85 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Parameter Description Setting Output If you check to set the Output Channel and the [How to set] Channel device is connected to an external alarm Click to select an indicator, the alarm indicator signals when an alarm is triggered.

  • Page 86: People Counting

    Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual NOTE  A drawn line cannot cross another one, or the line drawing fails.  Any shape with 8 sides at most can be drawn .  The quantity of deployment areas is not limited yet and will be described in future when a limit is applied.
  • Page 87 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual People Counting Set all parameters for illegal parking. Table 6-6 describes the specific parameters. Issue V1.0（2022-09-07）...
  • Page 88 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Parameters of People Counting Parameter Description Setting Enable Enable the button to enable the alarm. [How to set] Click Enable to enable. [Default value] OSD Enable Enable the OSD, the count data will show on live [How to set] video screen.

  • Page 89: Enter Area

    Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Parameter Description Setting Output If you check to set the Output Channel and the [How to set] Channel device is connected to an external alarm indicator, Click to select an the alarm indicator signals when an alarm is triggered.
  • Page 90 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Operation Procedure Select Intelligent Analysis > Enter Area to access the Enter Area setting interface, as shown in Figure 6-8. Enter area Set all parameters for illegal parking. Table 6-7describes the specific parameters. Parameters of Enter Area Parameter Description...
  • Page 91 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Parameter Description Setting Sensitivity The sensitivity of detecting the target, when the [How to set] value is high, the target can be detected easily, Choose from the but the accuracy will be lower. drop-down list [Default value] Limit Target...

  • Page 92: Leave Area

    Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Parameter Description Setting Video Stream Enable, the deployment frame will show on the [How to set] Draw Line live video. Click to enable Video Stream Draw Line. [Default value] Set a deployment area Move the cursor to the drawing interface and click to generate a point, move the cursor to draw a line, and then click to generate another point.
  • Page 93 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Leave Area Set all parameters for illegal parking. Table 6-8 describes the specific parameters. Parameters of Leave Area Parameter Description Setting Enable Enable the button to enable the leave area alarm. [How to set] Click Enable to enable.
  • Page 94 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Parameter Description Setting Limit Target Effective alarms are set based on target type, [How to set] Type with options of Person or Car, person, car. When Click to enable the device is used indoors, because of small Limit Target Type.
  • Page 95 Thermal Imaging Integrated Network Camera Intelligent Analysis User Manual Move the cursor to the drawing interface and click to generate a point, move the cursor to draw a line, and then click to generate another point. This is how a line is generated. In this way, continue to draw lines to form any shape, and right-click to finish line drawing.

  • Page 96: Advanced Intelligent Analysis

    Thermal Imaging Integrated Network Camera Advanced Intelligent Analysis User Manual Advanced Intelligent Analysis At advanced intelligent analysis interface, users can set the parameters of smoker detection, fire spot detection. Enable the linkage actions, the alarm information can be sent to users by the linkage. The advanced intelligent analysis can be used for detecting the smoking, if someone smoke in the indoor where is forbidden smoking.
  • Page 97 Thermal Imaging Integrated Network Camera Advanced Intelligent Analysis User Manual Smoker Detection Interface Set all parameters for Intrusion. Table 7-1 describes the specific parameters. Parameters of Smoker Detection Parameter Description Setting Enable At thermal channel, Enable the button to [How to set] enable the alarm.
  • Page 98 Thermal Imaging Integrated Network Camera Advanced Intelligent Analysis User Manual Parameter Description Setting Audible alarm Enable, when the alarm happens, it will [How to set] be play audio to alarm. Click to enable Audio Choose the audible alarm file (set at the Detection Alarm “Configuration >...

  • Page 99: Fire Spot Detection

    Thermal Imaging Integrated Network Camera Advanced Intelligent Analysis User Manual ⚫ A drawn line cannot cross another one, or the line drawing fails. ⚫ Any shape with 32 sides at most can be drawn. ⚫ The quantity of deployment areas is not limited yet and will be described in future when a limit is applied.
  • Page 100 Thermal Imaging Integrated Network Camera Advanced Intelligent Analysis User Manual Procedure Select Configuration > Advanced Intelligent Analysis > Fire Spot Detection to access the Fire Spot Detection interface, as shown in Figure 7-3. Fire Spot Detection Interface Set all parameters for Intrusion. Table 7-2 describes the specific parameters. Fire Spot Detection Description Parameter Description...
  • Page 101 Thermal Imaging Integrated Network Camera Advanced Intelligent Analysis User Manual Parameter Description Setting Output Channel If you check to set the Output Channel [How to set] and the device is connected to an external Click to select an ID. alarm indicator, the alarm indicator signals when an alarm is triggered.
  • Page 102 Thermal Imaging Integrated Network Camera Advanced Intelligent Analysis User Manual Set Deployment Area ⚫ A drawn line cannot cross another one, or the line drawing fails. ⚫ Any shape with 32 sides at most can be drawn. ⚫ The quantity of deployment areas is not limited yet and will be described in future when a limit is applied.
  • Page 103 Thermal Imaging Integrated Network Camera Advanced Intelligent Analysis User Manual Deployment Time Setting Interface ---End Issue V1.0（2022-09-07）...

  • Page 104: A Troubleshooting

    Thermal Imaging Integrated Network Camera A Troubleshooting User Manual A Troubleshooting Common Possible Cause Solution Trouble Unable to Network is not Connect the network cable of the camera to ⚫ access the connected. the PC to check whether the network cable is in good contact.
  • Page 105 Thermal Imaging Integrated Network Camera A Troubleshooting User Manual Common Possible Cause Solution Trouble Upgrade No network cable Ensure the upgrade network is connected. ⚫ ⚫ failed. is connected. Check whether the network setting is correct. ⚫ The network ⚫ setting is incorrect.

  • Page 106: B Common Emission Rate

    Thermal Imaging Integrated Network Camera B Common Emission Rate User Manual B Common Emission Rate Emission Rate The emission rate is the capability of an object to emit or absorb energy. An ideal transmitter provides an emission rate of emitting 100% of intake energy. An object with an emission rate of 0.8 can absorb 80% of intake energy, and reflect the remaining 20%.
  • Page 107 Thermal Imaging Integrated Network Camera B Common Emission Rate User Manual Cobalt 599/1110 0.19 199/390 0.52 Steel 599/1110 0.57 Tinned iron sheet (Light) 28/82 0.23 Brass(High-polish) 247/476 0.03 Brass (Tough rolled, polished 21/70 0.04 metal wire) Tinned Iron (Light) 0.13 Iron plate (Rust eaten) 20/68 0.69...
  • Page 108 Thermal Imaging Integrated Network Camera B Common Emission Rate User Manual Glass (Glossy) 22/72 0.94 Granite (Surfaced) 21/70 0.85 0/32 0.97 Marble (I Polished, grey) 22/72 0.93 Asbestos board 23/74 0.96 38/100 0.93 Asbestos paper 371/700 0.95 Asphalt ( Paving the road) 4/39 0.97 Paper ( Black tar)

Table of Contents