ZTE MF279T - 4G LTE Mobile WiFi Hotspot Quick Start Guide

ZTE MF279T - 4G LTE Mobile WiFi Hotspot Quick Start Guide

Also See for MF279T:

Advertisement

ZTE MF279T - 4G LTE Mobile WiFi Hotspot Quick Start Guide

Getting to Know Your Device

Getting to Know Your Device

Indicators

Indicator State Description
Power
Green steady On AC power
Green blinking On battery power
Off No power
Voicemail
Green blinking New voicemail waiting
Off No new voicemail
Wi-Fi
Green steady Wi-Fi on, no data transferring
Green flickering Wi-Fi on, data transferring
Off Wi-Fi off
Information
Green blinking Check the MF279T Web UI — New messages
Off No unread messages
Battery
Green steady More than 50% battery power
Yellow steady 20%-50% battery power
Red blinking Less than 20% battery power
Off Battery needs to be installed or replaced
Signal Strength
Blue steady Strong signal 3G/4G/HSPA+( antenna and 1,2,3,4bars)
Blue blinking 3G/4G/HSPA+ roaming ( antenna and 1,2,3,4bars)
Green steady Strong signal LTE( antenna and 1,2,3,4bars)
Green blinking LTE roaming ( antenna and 1,2,3,4bars)
Red steady No service, limited service, or searching for signal (antenna with RED and 0 bar)
Red blinking SIM checking, SIM error or other abnormal (antenna with RED and 0 bar. Blinking period: 2s )

Before You Begin

The MF279T uses the TELUS cellular network and DOES NOT use your home phone wall jacks.
Your device should be located:

  • Where you have a strong signal from a cell tower, typically near a window or outside wall. Signal strength may vary in different parts of your home.
  • Near an electrical wall outlet.
  • In the general area where you'll be using your home phone, computer, or Wi-Fi enabled device.
    Before You Begin - Device Location

Installation Guide

Install the Back-up Battery and nano-SIM Card (Optional)

  1. Remove the bottom of the device by pushing the entire cover in the direction of the arrow.
  2. Install the nano-SIM card (Optional).
    Installing the nano-SIM Card

  • Your device only supports a nano-SIM card.
  • To avoid damaging the device, please only use the card that is provided by TELUS and ensure that the nano-SIM card contacts are facing up when inserting it into the nano-SIM slot.
  1. Insert the back-up battery.
  2. Replace the cover.

Turn on Your Device

  1. Plug the power cord into an electrical wall outlet.
  2. Connect the other end of the power cord into the Power Input port on the back of your device.
  3. Slide the ON/OFF button to the ON position and you'll see the power light stays steady green.
    Turning on Your Device

Check the Wireless Signal

Wait a few seconds for the signal strength light to turn on, while your device connects to the cellular network.
Confirm signal strength light is green for optimal performance. Blue indicates a moderate signal and may be sufficient.
Checking the Wireless Signal

Connect Your Phone

Unplug Your Phone from the Wall Jack

Don't plug the MF279T directly to your home phone wall jack.
NOTE: If you have a cordless phone, keep it plugged into a power outlet.
Connect your phone - Unplug it from the Wall Jack

Connect Your Phone to the Device

Plug your phone into the "PHONE" port on the MF279T, using your existing phone cable or the included phone cable.
NOTE: Do not plug the device into your home phone wall jack.
Connecting your phone to the device

Place a Test Call

Place a test call from your connected home phone. Make sure to dial the 10-digit phone number, including area code.
For best results, place the cordless phone base at least 12 inches from the MF279T.

Important Phone Tips

  • Voicemail is included with your service. Dial "1" to set up and access. If you choose to use an answering machine instead, set it to fewer than 4 rings.
  • To place phones throughout your home, use a cordless phone system with multiple handsets. Wall jacks cannot be used with the MF279T.

Connect to the Internet

Select Your Internet Connection

To Connect via Wi-Fi:

  1. Open the Wi-Fi network manager on your computer or Wi-Fi enabled device.
  2. Find and select the Wi-Fi network name (SSID) (e.g., ZTE MF279T/2.4GXXXX or ZTE MF279T/5GXXXX, XXXX is the last 4 digits of MAC address).

To Connect via Ethernet:
Use an Ethernet cable (not included) to connect your computer or other device to the Ethernet port on the back of your device. Go to Telus.com (or your favorite website) to confirm your Internet connection.

Enter Wi-Fi Network Password

When prompted, enter the Wi-Fi password found on the bottom of the device.

Confirm Internet Connection

Go to Telus.com (or your favorite website) to confirm your Internet connection.
When your device is transmitting to and from the Internet, the Wi-Fi light will flicker green.
Confirmation of the Internet connection

Accessing the Configuration Page

To customize your device or view important messages about your device and data usage, use the configuration page.

  1. Make sure the connection between your devices is active (either by cable or Wi-Fi).
  2. Launch the Internet browser, and then enter http://192.168.0.1 (or other IP if you have changed it from the default) or http://telus.ztesmarthub directly into your browser address field and use "admin" as your login.

NOTE: The information light will blink green when you have a message.
Viewing important messages about your device

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download ZTE MF279T - 4G LTE Mobile WiFi Hotspot Quick Start Guide

Advertisement

Need help?

Need help?

Do you have a question about the MF279T and is the answer not in the manual?

Questions and answers

Table of Contents