Table of Contents
Advertisement
Quick Links
Wingspan
Length
Weight with Ba�.
Ba�ery
Flight Time
Transmi�er
Airplane Control
Motor
On-Board-Electronics
Specifications
15.75" (400mm)
11.25" (285mm)
1.4 oz. (40g)
1S 3.7v 400mAh LiPo
Up to 15 minutes
4-channel capable, 2.4GHz system
3-Channel - thro�le, rudder, elevator
8mm Coreless
Combina�on RX/ESC with Integrated 1.3-gram Servos
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Rage Micro Sport Cub S2
Summary of Contents for Rage Micro Sport Cub S2
- Page 1 Specifications Wingspan 15.75” (400mm) Length 11.25" (285mm) Weight with Ba�. 1.4 oz. (40g) Ba�ery 1S 3.7v 400mAh LiPo Flight Time Up to 15 minutes Transmi�er 4-channel capable, 2.4GHz system Airplane Control 3-Channel - thro�le, rudder, elevator Motor 8mm Coreless On-Board-Electronics Combina�on RX/ESC with Integrated 1.3-gram Servos...
-
Page 2: General Precautions
General Precautions • Never operate your model if the voltage is too low. • Always operate your model in an open area away from obstacles, people, vehicles, buildings, etc. • Carefully follow the and warnings for this and any support equipment. -
Page 3: Lipo Battery Warning
Micro Sport Cub RTF Contents LiPo Battery Warning warnings must be followed exactly to prevent property damage and/or personal injury Charging the LiPo Battery It is important to fully charge the LiPo before your first flight. The USB charger can be powered by the USB port on your computer or a wall plug USB port. -
Page 4: Install Transmitter Batteries
Micro Sport Cub Assembly The Micro Sport Cub comes nearly ready-to-fly. All that is required to complete is the installa�on of the landing gear. Insert the landing gear wire into the slot at the rear of the box. The wheels should be raked for- ward. -
Page 5: Control Functions
Binding Instructions Binding is the process of programming the receiver to recognize the GUID (Globally Unique fier) code of a single specific When a receiver is bound to a receiver will only respond to that specific If you need to rebind for any reason, please follow these steps: •... - Page 6 Center Control Surfaces With both the and the powered on and the PASS switch in the "No Assist" check the control surfaces for correct centering. If the surface is not centered, make the adjustment to the pushrod length by either opening or closing the gap at the U-shaped of the pushrod.
- Page 7 Control Movement Transmi�er Swing the Reac�on PASS Reac�on Opera�on Plane Elevator S�ck Pitch Reac�on Rudder S�ck Yaw Reac�on With the aircra� power on and the PASS With the aircra� power on and the PASS system system in Expert, check the elevator and in Par�al or Full Assist, check the elevator and rudder response as shown above.
-
Page 8: First Flight
Prop Saver Instructions Motor Prop Shaft Adapter Base Spinner Spinner Base Prop Screw Propeller Adapter Propeller Each Prop/Spinner set includes the propeller, spinner and prop adapter. See page 10 for specific part numbers for this airplane. The prop saver keeps the propeller and prop sha� from damage, along with preven�ng the electronic components from over current. -
Page 9: Parts List
Calibration The PASS system used in the Micro Sport Cub is pre-calibrated from the factory. Recalibration is only necessary if the aircraft does not respond correctly (pitches up or down) when the PASS switch is activated. With the aircraft sitting on a level surface and the tail raised to a “wings level”... -
Page 10: Limited Warranty
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Rage R/C exceed the individual price of the Product on which liability is asserted. As Rage R/C has no control over use, setup, final assembly, modifi... - Page 11 Notes...
- Page 12 Rage R/C, an exclusive brand of: © HRP Inc. Inc. Printed in China 12/22 2034 South 3850 West Salt Lake City, Utah 84104...
Need help?
Do you have a question about the Micro Sport Cub S2 and is the answer not in the manual?
Questions and answers