HMS Anybus 021440 User Manual

HMS Anybus 021440 User Manual

Wireless bridge ethernet-wlan

Advertisement

Quick Links

Anybus
®
Wireless Bridge
Ethernet–WLAN
USER MANUAL
HMSI-27-205 2.5 ENGLISH

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Anybus 021440 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for HMS Anybus 021440

  • Page 1 Anybus ® Wireless Bridge Ethernet–WLAN USER MANUAL HMSI-27-205 2.5 ENGLISH...
  • Page 2 Important User Information Liability Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks AB of any inaccuracies or omissions. The data and illustrations found in this document are not binding. We, HMS Industrial Networks AB, reserve the right to modify our products in line with our policy of continuous product development.
  • Page 3: Table Of Contents

    Table of Contents Page About This Document ....................3 Document history......................3 Conventions ........................4 Product Description ....................... 5 LED Indicators .......................5 WLAN Network Modes ....................6 Wireless Bridge Operating Modes ...................6 WLAN Security ......................7 Installation ........................8 Startup and Configuration .................... 9 Options for Device Configuration..................9 Factory Reset ........................9 SMART Configuration ....................10...
  • Page 4 This page intentionally left blank...
  • Page 5: About This Document

    About This Document 3 (38) About This Document This manual describes how to install and configure the Anybus Wireless Bridge Ethernet to WLAN 2.4 GHz, 5 GHz, and Dual-band models. For additional related documentation and file downloads, please visit the support website at www.anybus.com/support.
  • Page 6: Conventions

    This is a cross-reference within this document: Conventions, p. 4 This is an external link (URL): www.hms-networks.com This is additional information which may facilitate installation and/or operation. This instruction must be followed to avoid a risk of reduced functionality and/or damage to the equipment, or to avoid a network security risk.
  • Page 7: Product Description

    Product Description 5 (38) Product Description LED Indicators 2.1.1 Status LED Indicators Fig. 1 Status LED indicators LED Indication Meaning No power or no application running Steady Green Unit has power and application is running No wireless activity Steady Blue A wireless connection has been established Flashing Blue Wireless data activity...
  • Page 8: Wlan Network Modes

    Product Description 6 (38) WLAN Network Modes WLAN networking can be set up in two basic connection modes: Infrastructure (managed) mode Used when wireless devices connect through a WLAN access point. In infrastructure mode, all transmission speeds and encryption and authentication methods sup- ported by the hardware can be used, i.e.
  • Page 9: Wlan Security

    Product Description 7 (38) WLAN Security The following combinations of authentication and encryption methods are supported: Open Shared WPA/WPA2 LEAP PEAP Connection Secret No encryption WEP 64 WEP 128 TKIP x (WPA) AES/CCMP x (WPA2) • WPA/WPA2 PSK with TKIP encryption is considered a WPA connection. •...
  • Page 10: Installation

    Installation 8 (38) Installation Caution This equipment emits RF energy in the ISM (Industrial, Scientific, Medical) band. Make sure that all medical devices used in proximity to this device meet appropriate susceptibility specifications for this type of RF energy. This product contains parts that can be damaged by electrostatic discharge (ESD). Use ESD protective measures to avoid equipment damage.
  • Page 11: Startup And Configuration

    Startup and Configuration 9 (38) Startup and Configuration Options for Device Configuration SMART Configuration Basic use cases can be set up quickly using the MODE button and the A-B-C-D LEDs to select one of the SMART configuration modes. SMART Configuration, p. Web Configuration The built-in web server gives access to status information and configuration settings via a graphical user interface.
  • Page 12: Smart Configuration

    Startup and Configuration 10 (38) SMART Configuration Fig. 4 MODE button and LED indicators Power on the Wireless Bridge, then immediately press and release MODE. Press MODE repeatedly to cycle through the configuration modes until the desired mode is indicated by the LED combination. Press and hold MODE until the LEDs go out or blink, then release the button.
  • Page 13: Web Configuration

    Startup and Configuration 11 (38) Web Configuration The web configuration interface can be accessed by entering the IP address of the Anybus Wireless Bridge in any web browser that supports HTML5. The computer used for configuration must be in the same subnet as the Wireless Bridge. The default IP address is 192.168.0.98.
  • Page 14 Startup and Configuration 12 (38) 4.4.1 Settings – Standard View Fig. 7 Standard view Top Menu Info Return to the Info page but stay logged in. Logout Return to the Info page and log out. Advanced view Open the Advanced view (see Settings –...
  • Page 15 Startup and Configuration 13 (38) Network – IP Configuration IP Address The IP address of the Anybus Wireless Bridge. Default: 192.168.0.98 Subnet Mask Subnet mask. Default: 255.255.0.0 Default Gateway IP address of the transition point to other network segments. Must also be set when DHCP addressing is used.
  • Page 16 Startup and Configuration 14 (38) WLAN – WLAN Network Scan Search for available WLAN networks. The networks will be listed in the drop-down menu with their corresponding SSID and security modes. Assume & Set Confirm the WLAN network/SSID/security mode selection. WLAN Band Select either 2.4 or 5 GHz, or Auto (default) to scan both frequency bands.
  • Page 17 Startup and Configuration 15 (38) WLAN – Security Security Mode Select security profile. The security settings must be identical to those of the wireless network. Use Other to implement more unusual combinations of encryption and authentication. The settings are automatically taken from the network scan. Passkey Format Interprets the passkey as text (ASCII) or hexadecimal characters (0…F).
  • Page 18 Startup and Configuration 16 (38) SMART Mode Configuration SMART Modes SMART Configuration, p. Execute Apply the selected SMART configuration mode and reboot. Service – Change Password New Password Enter a new password for the web configuration interface. Confirm Password Enter the new password again. Confirm the new password (it will be required on the next login attempt).
  • Page 19 Startup and Configuration 17 (38) 4.4.2 Settings – Advanced View Fig. 8 Advanced view AT Commands AT Commands Enter AT commands into the field, then click on Set to upload them to the Anybus Wireless Bridge. AT Response Shows a log of the latest AT commands and their responses. Clear Clears the log window.
  • Page 20: Configuration Examples

    Configuration Examples 18 (38) Configuration Examples The following configuration examples require a basic understanding of how to install and power up Anybus Wireless Bridge and how to access and use SMART configuration modes. Read sections Product Description Startup and Configuration before you continue.
  • Page 21 Configuration Examples 19 (38) 5.1.3 Manual Configuration If any of the predefined IP addresses 192.168.0.98 and 192.168.0.99 are already in use on your network, or if the network uses DHCP addressing, the setup must be configured manually in the web interface for each unit. In the following example, static addressing is used and the two units are assigned IP addresses 192.168.0.101 and 192.168.0.102.
  • Page 22: Udp Tunnel Via Wlan Access Point

    Configuration Examples 20 (38) UDP Tunnel via WLAN Access Point 5.2.1 Overview Fig. 10 UDP Tunnel via WLAN Access Point This example describes two Wireless Bridges using UDP tunneling to connect two Ethernet net- work segments via a WLAN access point. Using an access point and infrastructure mode will result in higher performance than when con- necting directly in ad-hoc mode.
  • Page 23 Configuration Examples 21 (38) 5.2.3 Manual Configuration If any of the predefined IP addresses 192.168.0.98 and 192.168.0.99 are already in use on your network, the setup must be configured manually in the web interface for each unit. In the follow- ing example, IP addresses 192.168.0.101 and 192.168.0.102 are used.
  • Page 24: Two Single Clients Connected Via Ad-Hoc Network

    Configuration Examples 22 (38) Two Single Clients Connected via Ad-Hoc Network 5.3.1 Overview Fig. 11 Two Single Clients Connected via Ad-Hoc Network This example describes two Ethernet devices connecting via two Wireless Bridges in Single Cli- ent mode using an ad-hoc network. Single Client mode has higher performance than UDP Tun- neling since no encapsulation of the Ethernet packages is required.
  • Page 25 Configuration Examples 23 (38) 5.3.3 Manual Configuration Automatic configuration requires that a Wireless Bridge can send spontaneous ARP requests to retrieve the MAC address of the device at the other end. If this is not possible, the setup must be configured manually in the web interface for each unit. Device MAC should be set to the MAC address of the device connected to the Wireless Bridge.
  • Page 26: Multiple Single Clients Connecting Via Ad-Hoc Network

    Configuration Examples 24 (38) Multiple Single Clients Connecting via Ad-Hoc Network 5.4.1 Overview Fig. 12 Multiple Single Clients Connecting via Ad-Hoc Network This example describes three Ethernet devices connecting via Wireless Bridges in Single Client mode using an ad-hoc network. Only one Ethernet device can be connected to each Wireless Bridge.
  • Page 27: Single Clients Connected Via Wlan Access Point

    Configuration Examples 25 (38) Single Clients Connected via WLAN Access Point 5.5.1 Overview Fig. 13 Single Clients Connected via WLAN Access Point This example describes two Ethernet devices connecting using Wireless Bridges connected in Single Client mode via an access point. Only one Ethernet device can be connected to each Wireless Bridge.
  • Page 28: Pc Connected To Single Client Via Ad-Hoc Network

    Configuration Examples 26 (38) PC Connected to Single Client via Ad-Hoc Network 5.6.1 Overview Fig. 14 PC Connected to Single Client via Ad-Hoc Network This example describes a computer connecting to an Ethernet device via an ad-hoc network connection to a Wireless Bridge operating in single client mode. Ad-hoc connections between a Wireless Bridge and a Windows computer may be unstable and are normally not recommended.
  • Page 29: Pc Connected To Single Client Via Wlan Access Point

    Configuration Examples 27 (38) PC Connected to Single Client via WLAN Access Point 5.7.1 Overview Fig. 15 PC Connected to Single Client via WLAN Access Point This example describes a computer connecting to a single Ethernet device via a WLAN access point and a Wireless Bridge operating in single client mode.
  • Page 30: Single Clients Connected Via Wlan To A Wired Network

    Configuration Examples 28 (38) Single Clients Connected via WLAN to a Wired Network 5.8.1 Overview Fig. 16 Single Clients Connected via WLAN to a Wired Network This example describes two Ethernet devices connected via two Wireless Bridges and a WLAN access point to a wired network.
  • Page 31: Multiple Clients Connected Via Wlan Access Point

    Configuration Examples 29 (38) Multiple Clients Connected via WLAN Access Point 5.9.1 Overview Fig. 17 Multiple Clients Connected via a Wireless Bridge and a WLAN Access Point In the following example, two network segments are connected via a Wireless Bridge operating in Multiclient mode.
  • Page 32 This page intentionally left blank...
  • Page 33: A Wireless Technology Basics

    Appendix A: Wireless Technology Basics 31 (38) Wireless Technology Basics Wireless technology is based on the propagation and reception of electromagnetic waves. These waves respond in different ways in terms of propagation, dispersion, diffraction and re- flection depending on their frequency and the medium in which they are travelling. To enable communication there should optimally be an unobstructed line of sight between the antennas of the devices.
  • Page 34: B Technical Data

    Appendix B: Technical Data 32 (38) Technical Data Technical Specifications Model 2.4 GHz 5 GHz Dual-band Order code 021440 021450 024120 Dimensions (L x W x H) 91 x 66 x 36.2 mm Weight 120 g 130 g Operating temperature -30 to +65 °C Storage Temperature -40 to +85 °C...
  • Page 35: Internal Antenna Characteristics

    Appendix B: Technical Data 33 (38) Internal Antenna Characteristics Fig. 19 Longitudinal Axis Fig. 20 Transverse Axis Anybus ® Wireless Bridge Ethernet–WLAN User Manual HMSI-27-205 2.5...
  • Page 36: Regulatory Compliance

    When this product reaches its end of life, contact local authorities to learn about disposal and recycling options, or simply drop it off at your local HMS office or return it to HMS. For more information, see www.hms-networks.com.
  • Page 37 This equipment contains FCC ID: PVH0941 Any changes or modifications not explicitly approved by HMS Industrial Networks AB could cause the module to cease to comply with FCC rules part 15, and thus void the user's authority to operate the equipment.
  • Page 38: Licenses

    Appendix B: Technical Data 36 (38) Licenses This product contains software under the following licenses: Copyright (c) 2001–2004 Swedish Institute of Computer Science. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: Redistribution of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  • Page 39 This page intentionally left blank...
  • Page 40 HMSI-27-205 2.5.1578 / 2016-07-14 16:33 © 2016 HMS Industrial Networks AB...

This manual is also suitable for:

Anybus 021450Anybus 024120

Table of Contents