Removing The Battery (Figure F + K2 + N2 ); Before Initial Use; Charge The Battery; Battery Level Indicator (Figure U4 ) - Sabo 40-ACCU CLASSIC Operator's Manual

Removing the battery (figure F + K2 + N2 )

– Switch off the engine F .
– Open the battery cover and hold it open.
– Remove the safety key K2 .
– Press and hold the release button on the front of the battery and remove the
battery from the battery compartment N2 .
– For easier battery removal, press it into the battery compartment slightly before
pulling it out. Keep the release button pressed while doing this. The built-in
springs facilitate easier removal.
– Close the battery cover. Ensure that the cover closes automatically. Dirt and
grass residue can prevent this and must therefore be removed.

9 BEFORE INITIAL USE

Safety information!
For explanation of symbols, see the table on page 2
Check all screw connections for a tight fit. Tighten the screws, if necessary. You must
check the fastening of the cutter bar in particular (see chapter "Maintenance of the
cutter bar").
The blade fastening screw must always be tightened by an authorised workshop.
If the blade screw is tightened excessively or insufficiently, blade fastening and cutter
bar may be damaged or get loose, which can lead to serious injuries.
The lawn mower is fitted with an engine stop device.
Before using the equipment for the first time, make sure that the engine stop
safety control bar is working perfectly. When the safety control bar is released, the
cutter bar must come to a standstill within 3 seconds.
After release, the safety control bar must always return to the position shown in the
"Description of components" diagram.
If this is not the case, it must be checked immediately by an authorised workshop.
Risk of injury!
If the stopping time of the blade is longer, stop using the device and take it to an
authorised workshop.
Measuring the stopping time
After starting the engine, the blade rotates and a wind noise can be heard.
The stopping time corresponds to the duration of the wind noise after the engine has
been stopped; it can be measured with a stopwatch.
Machine safety and protective devices must not be manipulated or disabled.
Make sure that all protective devices have been attached properly and are not
damaged.

Charge the battery

The handling of the charger and battery is described
in the separate operating manual for the charger.
In particular, read and follow the safety information!
Charge the battery fully before initial use!
All safety information concerning the handling, storage,
safekeeping, transportation and disposal of the lithium-ion battery,
as well as first aid measures and measures for extinguishing
fires can be found in the "Product safety data sheet" on
www.sabo-online.com with the operating instructions.
Information hotline for lithium-ion batteries
+49 (0) 2261 704-0

Battery level indicator (figure U4 )

Pos: 10.22 /Innenteil/Batterie laden/Batteriestandanzeige Text neu @ 61\mod_1571832991676_6.docx @ 614904 @ @ 1
Press the battery level indicator button on the battery to check the available charge.
The indicator lamps light up according to the battery level:
Lamps
4 green lamps
3 green lamps
2 green lamps
1 green lamp
Lamps are off

10 STARTING THE ENGINE (FIGURE G2 + D )

Only start the engine when standing behind the mower.
Always place the mower on a level area which is not covered with high grass
(if the grass is too high it will block the start-up of the cutter bar and make the starting
process more difficult). When the engine is started, the machine must not be tilted on
end, if necessary it must be tilted by pressing the guide bar down so that the cutting
tool is pointing in the direction away from the user, but only as far as absolutely
necessary. As long as the device is not on all 4 wheels, both of your hands must be
on the top part of the bar.
– Open the battery cover and hold it open.
– Insert the safety key G2 .
– Close the battery cover. Ensure that the cover closes automatically.
Dirt and grass residue can prevent this and must therefore be removed.
– To switch on the engine, first press and hold the start button D .
– With your other hand, pull the control bar towards the top guide bar.
During operation, the control bar must remain held in this position.
– You can now let go of the start button.

11 SWITCHING OFF THE ENGINE (FIGURE F + K2 )

– Release the safety control bar F .
– Wait for the cutter bar to stop completely.
– Remove the safety key K2 .

12 EMERGENCY STOPPING

Release the safety control bar.
– The blade comes to a standstill.
– The engine will stop.
ATTENTION
Before every mowing job, make sure that the engine stop safety control bar is
working perfectly:
– When the safety control bar is released, the blade must come to a standstill
within 3 seconds.
If this is not the case, please consult your nearest authorised workshop.

13 GRASS COLLECTOR

Operation with grass collecting bag

WARNING
When operating the equipment with a grass collecting bag, the bag must be
completely assembled and in technically perfect condition.
When using the machine, ensure that the collecting bag is emptied in good time.
10
Capacity
Battery is fully charged
Battery has 70% charge or more
Battery has 45% charge or more
Battery has 10% charge or more and
must be charged again soon
Battery has less than 10% charge and
must be charged immediately to prevent
irreparable damage (total discharge)
Safety information!
For explanation of symbols,
see the table on page 2
Safety information!
For explanation of symbols, see the
table on page 2