Moxa Technologies NPort 5000AI-M12 Series Quick Installation Manual

NPort 5000AI-M12
Quick Installation Guide
First Edition, May 2010
Overview
NPort 5000AI-M12 device servers are designed to make serial
devices network-ready in an instant. It is complaint with EN
50155/EN 50121-4. So it can work on rolling stock and way side for
needing high level vibration environment. Use the NPort
5000AI-M12 device servers to give your PC software direct access to
serial devices from anywhere on the network.
Package Checklist
Before installing the NPort 5000AI-M12 series device servers, verify
that the package contains the following items:
• 1 NPort 5000AI-M12 series Device Server
• Documentation and Software CD
• Quick Installation Guide (printed)
• Warranty Card
Optional Accessories
• DR-45-24 45W/2A DIN-Rail 24 VDC Power Supply with
universal 85 to 264 VAC input
• DR-75-24 75W/3.2A DIN-Rail 24 VDC Power Supply with
universal 85 to 264 VAC input
• DR-120-24 120W/5A DIN-Rail 24 VDC Power Supply with
88 to 132 VAC/176 to 264 VAC input
• DK-TN-5308 DIN-Rail kit
Notify your sales representative if any of the above items is
missing or damaged.
Hardware Introduction
The NPort 5150AI-M12 series has a 3-in-1 (RS-232/422/485) DB9
serial port for serial data communication, the NPort 5250AI-M12
series has two 3-in-1 (RS-232/422/485) DB9 serial ports for serial
data communication, and the NPort 5450AI-M12 has four 3-in-1
(RS-232/422/485) DB9 serial ports for serial data communication.
P/N: 1802051503010
– 1 –
NPort 5150AI-M12 Appearance
NPort 5250AI-M12 Appearance
– 2 –
NPort 5450AI-M12 Appearance
The Reset to Default Button—Depress the Reset to default button
for 5 continuous seconds to load the factory default settings. Use a
pointed object, such as a straightened paper clip or toothpick, to
depress the Reset to default button. This will cause the Ready LED to
blink on and off. The factory default settings are loaded once the
Ready LED stops blinking (after about 5 seconds). At this point, you
can release the Reset to default button.
NPort 5000AI-M12 LED Indicators (front panel)
Name Color Function
PWR green Power is being supplied to the power input.
Steady on: Power is on and NPort is booting up.
Blinking: Indicates an IP conflict, or
red
DHCP/BOOTP server did not respond
properly.
Ready Steady on: Power is on and NPort is functioning
normally.
green
Blinking: The NPort has been located by NPort
Administrator's Location function.
off Power is off, or a power error condition exists.
orange 10 Mbps Ethernet connection.
10M,
green 100 Mbps Ethernet connection.
100M
off Ethernet cable is disconnected.
orange Serial port is receiving data.
P1, P2, green Serial port is transmitting data.
P3, P4
No data is being transmitted or received through
off
the serial port.
– 3 –
Hardware Installation Procedure
Panel/Wall Mounting
Mounting the NPort 5000AI-M12 on the wall requires 3 screws.
Please use the 3 screws packed in.
STEP 1: Prepare the 3 screw holes on the wall according to the
positions of the 3 screw holes on the device server shown on the
mounting dimension diagram.
STEP 2: Use one screw to go through the top-middle screw hole on
the device server and screw it into the wall.
STEP 3: Screw in the remaining 2 screws through the bottom-left
and bottom-right holes on the device server to the wall.
NOTE Please use the screws (M3 x 40 mm) included.
DIN-Rail Mounting (optional)
With the optional DIN-Rail mounting kit DK-TN-5308 (must be
purchased separately), you can mount the NPort 5000AI-M12 on a
35mm DIN-Rail.
STEP 1: Fix the DIN-Rail attachment plate onto the rear panel of the
device server as shown in the figure at the right.
- 4 -