Advertisement
Quick Links
Gigabit PoE Plus Injector & Splitter
Quick Installation Guide
English
Dansk
Slovenščina
POI-2001 & POS-1001
Gigabit PoE Injector & Splitter
POI-2002 & POS-1002
PoE Injector & Splitter
POI-3004
Gigabit PoE Injector
POI-3000 & POS-3000
POI-3002 & POS-3000
PoE Plus Injector & Splitter
Deutsch
Français
Ελληνικά
Italiano
繁體中文
한국어
Españ ol
Nederlands
Português
Svenska
Русский
Polish
Advertisement
Related Manuals for LevelOne POI-2001
Summary of Contents for LevelOne POI-2001
- Page 1 POI-2001 & POS-1001 Gigabit PoE Injector & Splitter POI-2002 & POS-1002 PoE Injector & Splitter POI-3004 Gigabit PoE Injector POI-3000 & POS-3000 Gigabit PoE Plus Injector & Splitter POI-3002 & POS-3000 PoE Plus Injector & Splitter Quick Installation Guide English Deutsch Français...
-
Page 2: Installation Steps
Installation Steps Step 1. Connect AC Power cord to the PoE Injector, and "Power" LED will light up. Schließ en Sie das Netzkabel an den PoE-Injektor an und die "Power"-LED leuchtet auf. Connectez le cordon d’alimentation secteur sur l’injecteur PoE, le voyant DEL "Power" (Alimentation) s’allume. - Page 3 Step 2. Connect "Data/In" port of Injector to Non PoE switch via Cat.5e/6/7 cable, and set the correct voltage (5V, 9V or 12V) by adjustable DIP switch on the side of PoE Splitter. (default setting 5V) Verbinden Sie den "Data/IN"-Port des Injektors über ein Cat.5e/6/7-Kabel mit dem Nicht-PoE-Switch.
- Page 4 Conecte a porta "Data/In" (Dados/Entrada) do injector ao switch não PoE através de um cabo Cat.5e/6/7 e defina a voltagem correcta (5V, 9V ou 12V) através do comutador DIP regulável situado na parte lateral do PoE Splitter. (a definição padrão é de 5V) ...
- Page 5 Συνδέστε την “Power + Data” θύρα του Splitter και την “P+D/out” θύρα του Injector με ένα Ethernet καλώδιο, και σιγουρευτείτε πως το “Power” LED Splitter είναι αναμμένο. Ligue a porta "Power+Data" (Entrada de Dados) do Separador e a porta "P+D/Out" (P+D/Saí...
- Page 6 (gegevensuitgang) van de splitter aan op de RJ45-poort van het netwerkapparaat. (Zorg dat u de juiste verwisselbare pen kiest voor het aandrijven van niet-PoE-apparaten.) Forbind “Power OUT” kablet på splitter til power jack på den tilknyttede netværks enhed og forbind “Data OUT” kablet på splitter til RJ45 port på netværks enheden. (væ r sikker på...
- Page 7 Step 5. Check whether the network device is on. If not, please make sure that power is on for Injector and Splitter, and all cables are connected correctly. Prüfen Sie, ob das Netzwerk-Gerät eingeschaltet ist. Wenn dies nicht der Fall ist, stellen Sie bitte sicher, dass die Stromversorgung für Injektor und Splitter hergestellt ist und alle Kabel richtig angeschlossen sind.