Delta DVP-SX Instruction Sheet page 2

Warning
EN DVP-SX is an OPEN-TYPE device. It should be installed in a control cabinet free of airborne dust, humidity,

electric shock and vibration. To prevent non-maintenance staff from operating DVP-SX, or to prevent an accident
from damaging DVP-SX, the control cabinet in which DVP-SX is installed should be equipped with a safeguard.
For example, the control cabinet in which DVP-SX is installed can be unlocked with a special tool or key.
EN DO NOT connect AC power to any of I/O terminals, otherwise serious damage may occur. Please check all wiring

again before DVP-SX is powered up. After DVP-SX is disconnected, Do NOT touch any terminals in a minute.
Make sure that the ground terminal
interference.
FR DVP-SX est un module OUVERT. Il doit être installé que dans une enceinte protectrice (boitier, armoire, etc.) saine,

dépourvue de poussière, d'humidité, de vibrations et hors d'atteinte des chocs électriques. La protection doit éviter
que les personnes non habilitées à la maintenance puissent accéder à l'appareil (par exemple, une clé ou un outil
doivent être nécessaire pour ouvrir a protection).
FR Ne pas appliquer la tension secteur sur les bornes d'entrées/Sorties, ou l'appareil DVP-SX pourra être

endommagé. Merci de vérifier encore une fois le câblage avant la mise sous tension du DVP-SX. Lors de la
déconnection de l'appareil, ne pas toucher les connecteurs dans la minute suivante. Vérifier que la terre est bien
reliée au connecteur de terre
 Introduction
Thank you for choosing the Delta DVP series PLC. The DVP-SX series PLC is a 10-point (4DI+2DO+2AI+2AO)
mixed PLC. İt has four digital input points, two digital output points, two 12-bit analog (voltage/current) input
channels, and two 12-bit analog (voltage/current) output channels. Besides, the DVP-SX series PLC has
bipolar voltage/current output capacity. It has a built-in two-digit seven-segment display corresponding to
internal specail registers. The two-digit seven-segment dispaly is used to display a station address or a
user-defined code. If an error occurs, the display will show "Er" and "01" or "02" alternately. ("01" indicates a
syntax error, and "02" indicates a PLC program loss).
 Product Profile and Outline
POWER indicator, RUN indicator,
ERROR indicator, BAT.LOW
1
indicator, AD indicator,
*1
ALARM *2 indicator
2 RUN/STOP switch
3 Two-digital seven-segment display 11 Nameplate
4 Digital I/O terminals
5 DIN rail clip
6 Analog I/O terminals
7 Input/Output indicators
8 COM1 (RS-232) (Rx) indicator
on DVP-SX is correctly grounded in order to prevent electromagnetic
afin d'éviter toute interférence électromagnétique.
Unit: mm
9 COM2 (RS-485) (Tx) indicator
COM1 (RS-232 port)
10
(Slave)
12 Extension port
Mounting hole of the extension
13
unit
14 DIN rail groove (35mm)
15 Extension unit clip
COM2 (RS-485 port)
16
(Master/Slave)
Terminal layout
A/D
D/A
17 DC power input
2-pin removable terminal
18
block (standard accessory)
Power input cable
19
(standard accessory)
20 Battery cover
21 Battery connector
22 Battery holder
ENGLISH
V0+
I0+
V1+
I1+
V0+
I0+
V1+
I1+
COM
S/S
X0
X1
X2
X3
C0
Y0
Y1
*3