Download Print this page
Mendota ML39- AA-11-04391 Installation And Operating Instructions Manual

Mendota ML39- AA-11-04391 Installation And Operating Instructions Manual

Fullview direct vent gas fireplace heater
Hide thumbs Also See for ML39- AA-11-04391:

Advertisement

Quick Links

l
MODEL NO. ML39- AA-11-04391, ML47- AA-11-04390, ML54- AA-11-04283, ML60- AA-11-04281, AND
ML72- AA-11-04593 FULLVIEW DIRECT VENT GAS FIREPLACE HEATER
WARNING: If the information in these instructions
is not followed exactly, a fire or explosion may
result causing property damage, personal injury or
loss of life.
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not
use any phone in your building.
Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call
the fire department.
- Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by local
codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gasses, unless a
certified kit is used.
A barrier designed to reduce the risk of burns from
the hot viewing glass is provided with this appliance
and must be installed.
85-03-01205-M
Installation and Operating Instructions
ML-SERIES FIREPLACE
AVERTISSEMENT. Assurez-vous de bien suivre les
instructions données dans cette notice pour réduire au
minimum le risque d'incendie ou d'explosion ou pour
éviter tout dommage matériel, toute blessure ou la mort.
Ne pas entreposer ni utiliser d'essence ni d'autres vapeurs
ou liquids inflammables dans le voisinage de cet appareil
ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucun interrupteur. Ne pas vous servir des
téléphones se trouvant dans le bâtiment où vous trouvez.
• Appelez immédiatement votre fournisseur de gaz depuis
un voisin. Suivez les instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incendies.
- L'installation et l'entretien doivent être assurés par un
installateur ou un service d'entretien qualifié ou par le
fournisseur de gaz.
Cet appareil peut être installé dans une maison
préfabriquée (É.-U. seulement) ou mobile déjà installée à
demeure si les règlements locaux le permettent.
Cet appareil doit être utilisé uniquement avec les types de
gaz indiqués sur la plaque signalétique. Une trousse de
conversion est fournie avec cet appareil.
Une barrière conçue pour réduire le risque de brûlures
du verre chaud est fournie avec cet appareil et doit être
installée.
Page 1

Advertisement

loading

Summary of Contents for Mendota ML39- AA-11-04391

  • Page 1 Installation and Operating Instructions MODEL NO. ML39- AA-11-04391, ML47- AA-11-04390, ML54- AA-11-04283, ML60- AA-11-04281, AND ML72- AA-11-04593 FULLVIEW DIRECT VENT GAS FIREPLACE HEATER WARNING: If the information in these instructions AVERTISSEMENT. Assurez-vous de bien suivre les is not followed exactly, a fire or explosion may instructions données dans cette notice pour réduire au...
  • Page 2 See chapter 3.1.1 Fireplace Curing Instructions. Read and follow all instructions given in this Chapter and perform the 3-step Mendota curing cycle. After the 3-step curing cycle has been completed, all smoking will have stopped. Some slight odors may remain. With subsequent use of this Fireplace, odors will slowly dissipate and disappear.
  • Page 3 URING ROCEDURE 1.3 H ........2 URFACES ARE ORMAL 1.4 P ..2 ERIODIC AND ANNUAL CLEANING ARE REQUIRED 3.2.4.3.1 Mendota Cool Wall33 3.2.4.3.2 Versiheat 2.1 SAFETY AND WARNING INFORMATION ....5 3.2.4.3.3 FlexHeat 2.2 S ..........6 AFETY ARNINGS 2.3 R...
  • Page 4 5.9 O ........76 PERATING NSTRUCTIONS 5.10 T ......76 AS TO IREPLACE 5.11 FREQUENTLY ASKED QUESTIONS ..... 77 4.10 ML72 DIRECT VENTING ........66 4.11 ML-SERIES POWER VENTING ......66 6.1 R ......81 4.12 V ........ 68 EQUIRED ERIODIC NSPECTIONS AMPER...
  • Page 5 Building Permit & Inspection Requirements All installations of Mendota Fireplaces must comply with all the requirements stated in this Installation and Operating Manual. The dealer and/or installer must obtain all required building permits and inspection approvals from the local building inspection department or the local jurisdiction.
  • Page 6 2.2 SAFETY WARNINGS HIGH-ALTITUDE INSTALLATION INFORMATION: Prior to installing at altitudes higher than 7,500 ft., understand the need for gas input derating. Contact Mendota Technical Service for support. INSTALLER NOTE: These instructions are to remain with homeowner. Be sure to read and understand all instructions carefully before starting the fireplace. Failure to follow these instructions may result in a possible fire hazard leading to property loss, injury or even death and will void all warranty.
  • Page 7 Never obstruct the flow of combustion and ventilat ion air. Keep the front of the fireplace clear of all obstacles and materials for servicing and proper operation. Use only Mendota approved Screens, Fronts and Trim Kits. Due to high temperature, the fireplace should be located out of traffic areas and away from furniture and draperies.
  • Page 8 été plongée dans l’eau. Do not use any fronts or doors with this fireplace unless they are certified by Mendota and installed by a certified installer.
  • Page 9 2.3 REQUIREMENTS FOR THE COMMONWEALTH OF MASS. The information in this section applies to all installations performed in the Common Wealth of Massachusetts only. For all side wall, horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes and where the side wall exhaust vent termination is less than seven (7) feet above grade, the following requirements shall be satisfied: 1.
  • Page 10 ATTENTION It is important that the blowers are turned on during this step to prevent the curing smoke from staining the wall finish above the fireplace. Mendota recommends completing Step 1 prior to installation of wall finish materials. Visible smoke and strong odor are to be expected during this step. If desired, disable smoke alarms before this step, smoke from the initial curing c ycle will set off smoke alarms.
  • Page 11 Please be aware that materials used around the fireplace will heat up and have the potential to cause odor issues. Adhesives, glue, wall substrate, wall finish material, paints and polishes are common materials that if used incorrectly will cause odor issues. Mendota is not responsible for any odor issues caused by materials used around the fireplace. 85-03-01205...
  • Page 12 3.2 MECHANICAL TECHNICAL REFERENCES Planning the installation This Mendota Fireplace must be installed and serviced by a qualified installer, service agency, or the gas supplier. When planning on appliance installation, it is necessary to determine the following information before installing: •...
  • Page 13 Listing Labels The listing label is located under the firebox. Remove the right-side access grill and locate the listing plate. It is chained to the shut off valve handle. Figure 3-1 Listing Labels 85-03-01205 ML-SERIES FIREPLACE Page 13...
  • Page 14 Other Warning and Caution Labels A few warnings or caution labels are attached to this appliance body as required per code to inform you of important facts. You can find these labels on the outer surface of this appliance. Make certain you heed all the warning and caution statements during installation and maintenance of this appliance. Figure 3-3 Figure 3-2 Figure 3-5...
  • Page 15 Figure 3-9 Figure 3-10 85-03-01205 ML-SERIES FIREPLACE Page 15...
  • Page 16 ML-SERIES Fireplace Ratings Information This Mendota Fireplace can be installed directly on top of a metal, masonry, or wood structural surface. ELECTRICAL REQUIREMENTS: 120 Volts AC, 3.5 Amps (minimum line voltage allowed 110 Volts AC) REQUIRED GAS SUPPLY PRESSURE: NAT. GAS: 7" W.C. [5.0" W.C. MIN., 11" W.C. MAX.] L.P.
  • Page 17 HINT: To greatly reduce surface temperatures surrounding this Fireplace during operation, Mendota recommends operating the integrated convection air blowers which aid in cooling all surrounding surfaces. Mendota Fireplaces comply with ANSI Z21.88-2017/CSA 2.33-2017 Standards for maximum surface temperatures on exposed “combustible” surfaces adjacent to the Fireplace.
  • Page 18 Fireplace Dimensions and Clearances ML39 ML47 ML54 ML60 ML72 MIN. ENCLOSURE FRAMING WIDTH ENCLOSURE SIDE TO VENT CENTER 34 1/2 37 1/2 MINIMUM FRAMING DEPTH 19 1/2 19 1/2 19 1/2 19 1/2 FINISHED FRAMING WIDTH MIN. ENCLOSURE CEILING 64 1/4 64 1/4 MIN.
  • Page 19 Convection Blower System Dual blowers are provided as standard equipment on the Mendota ML-Series Fireplaces. The dual blowers have an air output rating of 190 CFM (in free air). This Fireplace is designed to operate with the blowers turned off or on. Turning the blower on aids in distributing and circulating heat to the room this Fireplace is installed in.
  • Page 20 Lifting Handles Two lifting handles, one on each side are provided. The lifting handles make it possible to lift the unit onto a cart for transport. WARNING : The lifting handles are designed only for lifting and moving the fireplace short distances. Such as lifting the fireplace onto a transport cart or shifting the fireplace during installation.