Table of Content 1. Introduction ......................2 2. Appearance ......................3 3. Main Features ...................... 3 4. Set up Instruction ....................4 5. Data Report ......................5 5.1 Example of ReportDataCmd ................6 5.2 Example of ConfigureCmd ................7 5.3 Example for MinTime/MaxTime logic ............8 6.
1. Introduction R718DB2 is a 2-way long-range wireless spring-loaded vibration device for Netvox ClassA-type devices based on the LoRaWAN open protocol and is compatible with the LoRaWAN protocol. LoRa Wireless Technology: LoRa is a wireless communication technology dedicated to long distance and low power consumption. Compared with other communication methods, LoRa spread spectrum modulation method greatly increases to expand the communication distance.
Applicable to third-party platforms: Actility / ThingPark, TTN, MyDevices / Cayenne Low power consumption and long battery life Note: Battery life is determined by the sensor reporting frequency and other variables. Please refer to http://www.netvox.com.tw/electric/electric_calc.html On this website, users can find various types of battery lifetime in different configurations.
4. Set up Instruction On/Off Power on Insert batteries (Users may need a screwdriver to open) Turn on Press and hold the function key for 3 seconds and the green indicator flash once. Turn off (Restore to factory setting) Press and hold the function key for 5 seconds and the green indicator flashes 20 times. Power off Remove Batteries.
2. The device report interval will be programmed based on the default firmware which may vary. 3. The interval between two reports must be the minimum time. Please refer Netvox LoRaWAN Application Command document and Netvox Lora Command Resolver http://cmddoc.netvoxcloud.com/cmddoc to resolve uplink data.
Version– 1 byte –0x01——the Version of NetvoxLoRaWAN Application Command Version DeviceType– 1 byte – Device Type of Device The devicetype is listed in Netvox LoRaWAN Application Devicetype doc ReportType – 1 byte –the presentation of the NetvoxPayLoadData,according the devicetype NetvoxPayLoadData– Fixed bytes (Fixed =8bytes) Tips 1.
Example 2 of Uplink: 013D01A000010000000000 byte (01): Version byte (3D): DeviceType 0x3D - R718DB2 byte (01): ReportType byte (A0): Battery - 3.2V, 20(HEX)=32(DEC),32*0.1v=3.2v // Low battery byte (00): Status - off byte (01): Status - on byte (0000000000): Reserved 5.2 Example of ConfigureCmd FPort:0x07...
(2)Read Configuration: Downlink: 023D000000000000000000 Response: 823D003C003C0100000000(Current configuration) 5.3 Example for MinTime/MaxTime logic Example#1 based on MinTime = 1 Hour, MaxTime= 1 Hour, Reportable Change i.e. BatteryVoltageChange=0.1V MaxTime MaxTime Sleeping(MinTime) Sleeping(MinTime) Wake up and collects data Wakes up and collects data Wakes up and collects data REPORTS 3.6V REPORTS 3.6V...
This product comes with waterproof function. It can be attached to the iron surface, or the two ends can be fixed to the wall with screws. 1. The figure shows the vibration sensor (R718DB2) 3. When the sensor senses the vibration and the spring deforms, an applied to the scene of the mousetrap in the restaurant.
7. Information about Battery Passivation Many of Netvox devices are powered by 3.6V ER14505 Li-SOCl2 (lithium-thionyl chloride) batteries that offer many advantages including low self-discharge rate and high energy density. However, primary lithium batteries like Li-SOCl2 batteries will form a passivation layer as a reaction between the lithium anode and thionyl chloride if they are in storage for a long time or if the storage temperature is too high.
8. Important Maintenance Instruction Your device is a product of superior design and craftsmanship and should be used with care. The following suggestions will help you use the warranty service effectively. • Keep the equipment dry. Rain, moisture, and various liquids or moisture may contain minerals that can corrode electronic circuits.